[size=4]1. Command explanation: [/size][size=2][size=3]$PROJ_DIR$ indicates the path of the project. $TOOLKIT_DIR$ indicates the path of the header file where the IAR installation directory is located...
I am a student. Some time ago, a teacher gave me a few 2430s from Tianyun Technology. I found it difficult to learn by myself. I don't know where to start and there is no order. Now I want to send tem...
High power converters supporting all standard industry input voltagesThe DCM ChiP is an isolated, regulated DC-DC converter that operates from an unregulated wide range input to produce an isolated ou...
rt, it seems that the withstand voltage and maximum current of digital resistors are not too large. Is it feasible to do this? Can I use a digital resistor to control a small thyristor first, and then...
Data memory and program memory experiment Experimental purpose: Understand the structure of DSP internal data memory and program memory Understand several addressing methods of DSP instructions Experi...
0. Preparation First use st-link to connect the stm32 core board and PC for burning St-link Stm32 3.3V 3.3V GND GND SWDIO PART SWCLK DCLK Then connect with USB serial port board to v...[Details]
Function List and Notes (lower-level driver part) 1. IO port initialization: control IO and communication IO. Control includes power control, reset and low power mode. Communication is the serial po...[Details]
In the development of artificial intelligence, talent reserve is undoubtedly an important part. Artificial intelligence should be a bottom-level technology that can be deeply embedded in any indust...[Details]
Different from 51, AVR and other single-chip microcomputers, the clock signal sources of msp430 include LFXT1, XT2 and DCO. 1. LFXT1: It can connect high-speed and low-speed crystal oscillators. In l...[Details]
When Amazon quietly launched a product called Elastic Computing Cloud 12 years ago, the Internet industry in China, across the ocean, also ushered in an unprecedented development opportunity. Let's...[Details]
On May 8,
Google
I/O 2018 Developer Conference was held as scheduled in Mountain View, California. In the second year of the full promotion of the "AI first" strategy, artificial intelligen...[Details]
The storage media corresponding to the three boot modes of STM32 are built-in to the chip, they are: 1. User Flash = Flash built into the chip 2.SRAM = RAM area built into the chip, which is the m...[Details]
The key is the configuration of registers. The T1 timer (16 bits) of CC2530 needs to configure three registers: T1CTL, T1STAT, IRCON Here is just a brief introduction. For more details, please refer ...[Details]
When the program starts running, light A turns on for 5 seconds, then turns off, light B turns on for 5 seconds, light B turns off, light C turns on for 5 seconds, light C turns off, the program ends...[Details]
****************************************************************** 1. The operand is in register, R0--R7 2. Operands are in internal RAM 3. Operands are in external RAM But they are all similar. For ...[Details]
;Question: The 80C51 single-chip microcomputer has a fosc = 6MHz. It is required to use the T1 timer working mode 1 to perform a timing of 40ms. And P1.7 periodically outputs a rectangular wave with ...[Details]
MCS-51 single-chip microcomputer timer/counter experiment programming program Programming requirements: 1. Connect a light-emitting diode LED to the P1.0 pin, light up for two seconds, turn off for o...[Details]
Design a second and minute pulse generator for a single-chip microcomputer using the interrupt method. Assume that P1.0 generates a positive pulse of one machine cycle per second, and P1.1 generates ...[Details]
Requirements: Set timer T1 as an external event counter, count 500 pulses every time, then switch T1 to timing mode and output a positive pulse with a width of 10ms at P1.2. Over and over again. A...[Details]
stm32/stm8
京公网安备 11010802033920号
EEWORLD
