EEWORLDEEWORLDEEWORLD

Part Number

Search

BSTCR-202-S-090-22-G-100-LT

Description
Board Connector, 2 Contact(s), 1 Row(s), Male, Right Angle, 0.079 inch Pitch, Solder Kinked Leads Terminal, Black Insulator, Receptacle
CategoryThe connector    The connector   
File Size160KB,1 Pages
ManufacturerMajor League Electronics
Websitehttp://www.mlelectronics.com/
Download Datasheet Parametric View All

BSTCR-202-S-090-22-G-100-LT Overview

Board Connector, 2 Contact(s), 1 Row(s), Male, Right Angle, 0.079 inch Pitch, Solder Kinked Leads Terminal, Black Insulator, Receptacle

BSTCR-202-S-090-22-G-100-LT Parametric

Parameter NameAttribute value
Is it Rohs certified?incompatible
Reach Compliance Codecompliant
ECCN codeEAR99
Other featuresBOARD STACKING CONNECTOR
body width0.14 inch
subject depth0.109 inch
body length0.158 inch
Body/casing typeRECEPTACLE
Connector typeBOARD CONNECTOR
Contact to complete cooperationGOLD (10) OVER NICKEL (50)
Contact completed and terminatedGold Flash (Au) - with Nickel (Ni) barrier
Contact point genderMALE
Contact materialPHOSPHOR BRONZE
contact modeRECTANGULAR
Contact styleSQ PIN-SKT
Insulation resistance5000000000 Ω
Insulator colorBLACK
insulator materialGLASS FILLED POLYESTER
Manufacturer's serial numberBSTCR
Plug contact pitch0.079 inch
Installation methodRIGHT ANGLE
Installation typeBOARD
Number of connectorsONE
PCB row number1
Number of rows loaded1
Maximum operating temperature125 °C
Minimum operating temperature-65 °C
PCB contact patternRECTANGULAR
Plating thickness10u inch
Rated current (signal)2 A
GuidelineUL
reliabilityCOMMERCIAL
Terminal length0.09 inch
Terminal pitch2.0066 mm
Termination typeSOLDER KINKED LEADS
Total number of contacts2
Highlights of the week: 17.8.7-17.8.13
[size=4]Hi, good morning everyone. It's time for our weekly review~~ Come and see what kind of good posts there are in the past week. [/size][size=4] [/size] [size=4][color=#ff0000][b]Recommended wond...
okhxyyo Talking
An interesting phenomenon of 51 MCU IO port operation
I want to achieve synchronous output of P1.1 port following P1.4 port, both of which drive LEDs. P1.4 port uses [url=http://article.ednchina.com/word/178833.aspx]timer[/url] to flip regularly, and the...
maker Test/Measurement
The op amp output noise contains the switching frequency of DCDC, but the power supply is actually very clean. How to improve it?
[i=s]This post was last edited by samyang13 on 2020-10-11 15:08[/i]Hello everyone, I recently tested the output of the PA78 amplifier, which is only used for DC amplification, but found that the rippl...
samyang13 Analog electronics
I am completely helpless!
Hello everyone: I have recently done an experiment on sending and receiving text messages via GPRS. After receiving the text message, I parse the number and content, and then reply to the content requ...
mcmamman Embedded System
REMAP, Bootloader, Flashloader
1. REMAP:When it comes to REMAP, we should first think of what MAP is. I am not good at English, so I started with a quote out of context. MAP is a map, and Memory Map is a memory map. However, the re...
sdjntl MCU
Wind power introduction
Wind power  Wind energy is usually referred to as the kinetic energy of air flow. Wind power generation is the conversion of the kinetic energy of air flow into electrical energy. Strong winds contain...
beh Industrial Control Electronics

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1728  315  2217  2773  2330  35  7  45  56  47 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号