EEWORLDEEWORLDEEWORLD

Part Number

Search

BSTC-239-D-130-06-G-120-LT

Description
Board Connector, 78 Contact(s), 2 Row(s), Male, Straight, 0.079 inch Pitch, Solder Kinked Leads Terminal, Black Insulator, Receptacle
CategoryThe connector    The connector   
File Size153KB,1 Pages
ManufacturerMajor League Electronics
Websitehttp://www.mlelectronics.com/
Download Datasheet Parametric View All

BSTC-239-D-130-06-G-120-LT Overview

Board Connector, 78 Contact(s), 2 Row(s), Male, Straight, 0.079 inch Pitch, Solder Kinked Leads Terminal, Black Insulator, Receptacle

BSTC-239-D-130-06-G-120-LT Parametric

Parameter NameAttribute value
Is it Rohs certified?incompatible
Reach Compliance Codecompliant
ECCN codeEAR99
Other featuresBOARD STACKING CONNECTOR
body width0.155 inch
subject depth0.12 inch
body length3.081 inch
Body/casing typeRECEPTACLE
Connector typeBOARD CONNECTOR
Contact to complete cooperationGOLD (10) OVER NICKEL (50)
Contact completed and terminatedGold Flash (Au) - with Nickel (Ni) barrier
Contact point genderMALE
Contact materialPHOSPHOR BRONZE
contact modeRECTANGULAR
Contact styleSQ PIN-SKT
Insulation resistance5000000000 Ω
Insulator colorBLACK
insulator materialGLASS FILLED POLYESTER
Manufacturer's serial numberBSTC
Plug contact pitch0.079 inch
Match contact row spacing0.079 inch
Installation methodSTRAIGHT
Installation typeBOARD
Number of connectorsONE
PCB row number2
Number of rows loaded2
Maximum operating temperature125 °C
Minimum operating temperature-65 °C
PCB contact patternRECTANGULAR
PCB contact row spacing2.0066 mm
Plating thickness10u inch
Rated current (signal)2 A
GuidelineUL
reliabilityCOMMERCIAL
Terminal length0.13 inch
Terminal pitch2.0066 mm
Termination typeSOLDER KINKED LEADS
Total number of contacts78
LinKIt ONE Review (2)
[i=s]This post was last edited by ihalin on 2017-2-28 08:35[/i] [font=Arial][size=5]Next post:[/size][/font][url=https://bbs.eeworld.com.cn/thread-521245-1-1.html]LinKIt ONE Evaluation (1)[/url] [font...
ihalin stm32/stm8
Matter Development Guide (V): Firmware Compilation and Burning
We have already set up the Matter compilation environment, so this time we can proceed with the compilation and burning steps.To compile the Matter firmware, you need to operate in the Matter root dir...
okhxyyo RF/Wirelessly
In circuit design, how to connect the "ground"
In addition to correctly designing and installing the grounding, it is also necessary to correctly handle the grounding of various different signals. In the control system, there are roughly the follo...
电子研发_lp 51mcu
4. "Wanli" Raspberry Pi car - C++ learning (compile and run, use geany)
In the past, when learning C language or embedded programming, there was an IDE. In the Windows environment, you hardly had to worry about compilation and linking. However, in the Linux environment, y...
lb8820265 Creative Market
Interruption problem during delay process
I wrote a test program in EWAVR, but I am confused about the interruption problem during the delay process: If there is no delay program, the light on the test board is almost always on. After adding ...
congyue Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1853  2699  358  570  316  38  55  8  12  7 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号