D-SUB-205AK09KANBBD3 datasheet, PDF

D-SUB-205AK09KANBBD3: DescriptionD Type Connector, 9 Contact(s), Female, 0.109 inch Pitch, Solder Terminal, #4-40, Plug; CategoryThe connector The connector; File Size124KB，1 Pages; ManufacturerPalPilot

Download Datasheet Parametric View All

D-SUB-205AK09KANBBD3 Overview

D Type Connector, 9 Contact(s), Female, 0.109 inch Pitch, Solder Terminal, #4-40, Plug

Parameter Name	Attribute value
Reach Compliance Code	compliant
ECCN code	EAR99
Other features	ROHS COMPLIANT
body width	0.492 inch
subject depth	0.492 inch
body length	1.213 inch
Body/casing type	PLUG
Contact to complete cooperation	AU ON NI
Contact completed and terminated	TIN OVER NICKEL
Contact point gender	FEMALE
Contact material	COPPER ALLOY
contact mode	STAGGERED
Contact resistance	15 mΩ
Contact style	RND PIN-SKT
Dielectric withstand voltage	1000VAC V
Insulation resistance	3000000000 Ω
Insulator color	BLACK
insulator material	POLYAMIDE
Manufacturer's serial number	205
Plug contact pitch	0.109 inch
Match contact row spacing	0.112 inch
Installation option 1	#4-40
Installation option 2	RIVET
Installation method	RIGHT ANGLE
Installation type	BOARD
PCB row number	2
Number of rows loaded	2
Maximum operating temperature	105 °C
Minimum operating temperature	-55 °C
PCB contact pattern	STAGGERED
PCB contact row spacing	2.8448 mm
Plating thickness	5u inch
Rated current (signal)	3 A
Guideline	UL
reliability	COMMERCIAL
Shell surface	NICKEL
Shell material	STEEL
Terminal length	0.125 inch
Terminal pitch	2.7686 mm
Termination type	SOLDER
Total number of contacts	9

High frequency small signal amplification: I am planning to amplify a small signal of about 5MHz, which is only a few to ten mV. I don't know how to choose a suitable op amp with an amplification factor of about 50. The op amp has a BW@Acl uni...; dlcnight Analog electronics

IPM input is normal, output has problems: [backcolor=rgb(239, 245, 249)]I use a 28335 chip to control an optocoupler. The rectangular wave is normal when it passes through the optocoupler and reaches the IPM. I add 15 or 20V to the IPM module...; 善如雪 DSP and ARM Processors

Newbie question! What is the problem if the displayed count does not move?: Question: What is the problem if the counter does not work? The boards have these chips: 74373 (02 08 10 21 07 32 175 154 138 245 573), 8155, 12887, cy7c136, W78E516B, oks1235, etc. I don't use 74193....; ddfood MCU

What are the ways for Windows CE to communicate with GPRS network?: Just as the title says, thank you!...; cfly Embedded System

LED drive precise control method (with photos): [b][color=black]When it comes to LED drive accuracy, constant current error usually comes to mind. In fact, drive accuracy is not limited to current accuracy. LED is a typical current-driven device. A...; qwqwqw2088 DIY/Open Source Hardware

Why can't the output power of the switching power supply be increased?: I made a dual-tube forward switching power supply, and I wanted the output power to be 150W, but when I actually measured it with a 1 ohm resistor, it was only about 6A, which means the actual output ...; reohad Power technology

Shortcut: A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 AA AB AC AD AE AF AG AH AI AJ AK AL AM AN AO AP AQ AR AS AT AU AV AW AX AY AZ B0 B1 B2 B3 B4 B5 B6 B7 B8 B9 BA BB BC BD BE BF BG BH BI BJ BK BL BM BN BO BP BQ BR BS BT BU BV BW BX BY BZ C0 C1 C2 C3 C4 C5 C6 C7 C8 C9 CA CB CC CD CE CF CG CH CI CJ CK CL CM CN CO CP CQ CR CS CT CU CV CW CX CY CZ D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 DA DB DC DD DE DF DG DH DI DJ DK DL DM DN DO DP DQ DR DS DT DU DV DW DX DZ

Popular Components