EEWORLDEEWORLDEEWORLD

Part Number

Search

M80-4T1180100-03-302-12-301

Description
Board Connector, Female, Straight, Solder Terminal, Locking, Black Insulator, Plug
CategoryThe connector    The connector   
File Size1MB,6 Pages
ManufacturerHarwin
Websitehttp://www.harwin.com/
Download Datasheet Parametric View All

M80-4T1180100-03-302-12-301 Overview

Board Connector, Female, Straight, Solder Terminal, Locking, Black Insulator, Plug

M80-4T1180100-03-302-12-301 Parametric

Parameter NameAttribute value
Is it Rohs certified?incompatible
Reach Compliance Codecompliant
ECCN codeEAR99
body width0.219 inch
subject depth0.205 inch
body length3.465 inch
Body/casing typePLUG
Connector typeBOARD CONNECTOR
Contact to complete cooperationAU
Contact completed and terminatedTin/Lead (Sn/Pb)
Contact point genderFEMALE
Contact materialBERYLLIUM COPPER
Contact resistance25 mΩ
Contact styleRND PIN-SKT
Durability500 Cycles
Insulation resistance100000000 Ω
Insulator colorBLACK
insulator materialGLASS FILLED POLYPHENYLENE SULPHIDE
JESD-609 codee0
Manufacturer's serial numberM80
Mixed contactsYES
Installation option 1LOCKING
Installation methodSTRAIGHT
Installation typeBOARD
Number of connectorsONE
Maximum operating temperature125 °C
Minimum operating temperature-55 °C
Plating thickness12u inch
Rated current (signal)3 A
GuidelineUL
reliabilityCOMMERCIAL
Terminal length0.118 inch
Termination typeSOLDER
My emergency light is fully completed. See the picture.
All the components I used are from MAXIM. Although the workmanship is not very particular, you can take a look at them for reference. The pictures were supposed to be uploaded tomorrow, but because my...
ddllxxrr DIY/Open Source Hardware
How to debug nandflash?? (as the title says software debugging)
Anyone who has done this before, please give me some tips. Thanks....
yangjunweimail Embedded System
Pull-up and pull-down resistors
Sometimes the unused pins of a chip cannot be left floating, and a pull-up resistor or a pull-down resistor is needed to make it at a high or low level. Why not connect it directly to the power supply...
zhonghuadianzie Analog electronics
How to convert ±8V signal into 0~5V signal?
The op amp is used as a comparator, powered by a single 0~5V LM324 power supply, the negative pin is connected to a +2.5V DC potential, and the positive pin is connected to a ±8V signal. For some reas...
7mofnahq Analog electronics
micropython update: 2020.7
zephyr/make-minimal: Disable FAT and LFS2 options to make it build. zephyr: Implement machine.Pin.irq() for setting callbacks on pin change. lib/utils: Protect all of mpirq.c with MICROPY_ENABLE_SCHED...
dcexpert MicroPython Open Source section

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1724  1376  2252  2473  1849  35  28  46  50  38 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号