EEWORLDEEWORLDEEWORLD

Part Number

Search

54122-813-11-1100R

Description
Board Connector, 22 Contact(s), 2 Row(s), Male, Straight, 0.1 inch Pitch, Solder Kinked Leads Terminal, Locking, Black Insulator, Receptacle,
CategoryThe connector    The connector   
File Size107KB,1 Pages
ManufacturerAmphenol
Websitehttp://www.amphenol.com/
Download Datasheet Parametric View All

54122-813-11-1100R Overview

Board Connector, 22 Contact(s), 2 Row(s), Male, Straight, 0.1 inch Pitch, Solder Kinked Leads Terminal, Locking, Black Insulator, Receptacle,

54122-813-11-1100R Parametric

Parameter NameAttribute value
Is it Rohs certified?incompatible
Reach Compliance Codecompliant
ECCN codeEAR99
body width0.19 inch
subject depth0.433 inch
body length1.1 inch
Body/casing typeRECEPTACLE
Connector typeBOARD CONNECTOR
Contact to complete cooperationAU ON NI
Contact completed and terminatedTin/Lead (Sn/Pb) - with Nickel (Ni) barrier
Contact point genderMALE
Contact materialPHOSPHOR BRONZE
contact modeRECTANGULAR
Contact styleSQ PIN-SKT
Insulation resistance5000000000 Ω
Insulator colorBLACK
insulator materialTHERMOPLASTIC
JESD-609 codee0
Manufacturer's serial number54122
Plug contact pitch0.1 inch
Match contact row spacing0.1 inch
Installation option 1LOCKING
Installation methodSTRAIGHT
Installation typeBOARD
Number of connectorsONE
PCB row number2
Number of rows loaded2
Maximum operating temperature125 °C
Minimum operating temperature-65 °C
PCB contact patternRECTANGULAR
PCB contact row spacing2.54 mm
Plating thickness15u inch
Rated current (signal)3 A
GuidelineUL, CSA
reliabilityCOMMERCIAL
Terminal length0.12 inch
Terminal pitch2.54 mm
Termination typeSOLDER KINKED LEADS
Total number of contacts22
PDM: Rev:K
STATUS:
Released
Printed: Mar 10, 2011
.
SPI problem with STM32
Does STM32 need to send a data before it can read it when reading SPI? I can write SPI successfully now, but I can't read the data from the device. The SPI read function is as followsuint8_t SpiReadRe...
morewater stm32/stm8
How does this function eliminate key jitter?
The following is the scan debounce function: void keyscan() { if(s2==0) //S2 is an independent key { while(s2==0); //I want to ask why if S2 is pressed and not released, NUM should be increasing all t...
16816 51mcu
[TI millimeter wave radar evaluation]_4_boost board evaluation encountered problems 2
[i=s]This post was last edited by wangran_95 on 2019-12-31 08:47[/i]After using the device, I found that it was hard to find a power supply. There were two boards and two power supplies, so I had to c...
wangran_95 TI Technology Forum
【FPGA(cyclone4) Issue 2】 Timing and Simulation Learning - Traditional Divider
[color=#000][font=Tahoma][size=3][b]The concept of traditional division is the same as that of traditional multiplication. Multiplication is an accumulation process, while division is a decremental pr...
wsdymg FPGA/CPLD
Ask a weak question
When using MAX232 to make an RS232 interface, is it necessary to use the RX and TX pins of the 51 microcontroller? Can other pins be used?...
yanxinghua Embedded System
IC41C16256-25K Function Tester
Hello: Simple operation can determine whether the chip is good or bad! IC41C16256-25K functional tester is the latest dedicated chip tester launched by CECCLab. It has the characteristics of simple op...
cecc-2010 Power technology

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1010  363  1195  19  219  21  8  25  1  5 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号