EEWORLDEEWORLDEEWORLD

Part Number

Search

K4AACDBBBB

Description
Toggle Switch, SPST, (on)-off, Momentary, 10A, 28VDC, Quick Connect Terminal, Toggle Bat Actuator, Panel Mount
CategoryMechanical and electronic products    switch   
File Size2MB,3 Pages
ManufacturerOTTO
Websitehttp://www.ottoexcellence.com
Environmental Compliance
Download Datasheet Parametric View All

K4AACDBBBB Overview

Toggle Switch, SPST, (on)-off, Momentary, 10A, 28VDC, Quick Connect Terminal, Toggle Bat Actuator, Panel Mount

K4AACDBBBB Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
Reach Compliance Codeunknown
ECCN codeEAR99
Actuator length0.94 inch
Actuator materialSTAINLESS STEEL
Actuator typeTOGGLE BAT
body width21.844 mm
body height26.67 mm
Body length or diameter24.892 mm
Center contact platingSILVER
Contact (AC) maximum rated R load10A@250VAC
Maximum contact current (AC)10 A
Maximum contact current (DC)10 A
Contact (DC) maximum rated R load10A@28VDC
Contact function(ON)-OFF
Maximum contact voltage (AC)250 V
Maximum contact voltage (DC)28 V
Electrical life50000 Cycle(s)
End contact platingSILVER
insulator materialTHERMOPLASTIC
Manufacturer's serial numberK4
Installation featuresPANEL MOUNT
Maximum operating temperature85 °C
Minimum operating temperature-30 °C
surface mountNO
Switch actionMOMENTARY
switch functionSPST
Switch typeTOGGLE SWITCH
Terminal length0.4 inch
Termination typeQUICK CONNECT
K4
SNAP-IN
TOGGLES
SEALED, ILLUMINATED SNAP-IN TOGGLE
LOW COST, SNAP-IN TOGGLE FOR WET & DUSTY ENVIRONMENTS, 1 & 2 POLES
The K4 series snap-in toggle switches are rugged, high
performance sealed switches designed for use under severe
conditions found in marine, appliance, heavy equipment and
industrial control applications. They are totally sealed so the
switch can withstand direct water spray and submersion,
even during operation. Sealed to IP68S with an optional panel
seal available.
The K4 series is offered in single and double pole configurations.
Toggle action includes 2 and 3-position, momentary and
maintained operation in a combination of 13 variations.
Mounting is simple and quick; snaps into panel from the
front. The OTTO snap-in design supports a variety of panel
thicknesses with just one cutout size specified.
Existing unsealed applications are easily upgraded to
sealed functionality because the K series drops into existing
panel cutouts.
A choice of models are offered to handle current from 16 amps to
low level electronic switching levels.
Single & Double Pole
LED, Neon or
Incandescent Illumination
Features:
• Withstands direct water spray
• Sealed to IP68S
• Fits industry standard panel openings for drop-in
replacement of panel sealed & unsealed switches
• Snap-in feature accommodates a wide range of
panel cutouts
• Switches up to 16 amps
• UV & solvent resistant
• Withstands extreme shock & vibration
• Legends & illuminated function indicators available
• 2 & 3-position, momentary, maintained action
& center OFF
• RoHS/WEEE/Reach compliant
Standard Characteristics/Ratings:
ELECTRICAL RATINGS:
Load
Resistive
Resistive
Inductive
Lamp
Motor
DWV
Low Level
Electrical Life:
Sea Level @ 28VDC
or 125/250VAC, 60Hz
16A
10A
10A
5A
0.5HP
10mA @ 30mV
See Rating Chart
Cycles
25,000
50,000
25,000
25,000
25,000
100,000
1050Vrms except across light terminals
LIGHTING:
Light Source
Incandescent
Neon
LED
Mechanical Life:
Seal:
Rating
(VDC) 6V, 12V, 24V
(VAC) 125V, 250V
(VDC) 2V, 6V, 12V, 24V
100,000 cycles
IP68S
Operating Temp Range:
-30°C to +85°C
MATERIALS:
Case:
Toggle:
Terminals/Contact:
Terminal Hardware:
Thermoplastic
Stainless steel
Brass, silver alloy with silver plate, gold plate for low level
Screws and lockwashers provided when applicable
K4 series recommended Quick Connect terminals:
AMP 60253-2 for 12-16 AWG
AMP 42100-2 for 14-18 AWG
None provided
Mounting Hardware:
156
OTTO Full Line Catalog
Specifications Subject To Change Without Notice
Please give me some advice if you have transplanted TCP/IP protocol stack!
I want to port LWIP to UCOS. The information on the Internet is based on the ARM platform, but I want to port it to the PC platform. Is there any hero who can give me some advice? Thank you very much....
min_sd Embedded System
Keil Learning (IV)
[b]III. Breakpoint Setting[/b] Figure 3 When debugging a program in the online assembly window, some program lines must meet certain conditions before they can be executed (such as a variable in the p...
yuandayuan6999 MCU
Sharing FPGA Design Tips
Counters are often used in FPGA design. Counters should be designed as subtraction counters instead of addition counters. This design can reduce the occupation of design resources and improve design r...
eeleader FPGA/CPLD
CCS5.2 released
CCS5.2 has been released, with the following changes compared to previous versions:Support on Windows and Linux, including SYS/BIOS, ELF, ULP Advisor, and Flash differential downloadNow fully supports...
wstt Microcontroller MCU
How to use the OffsetWindowOrgEx function in wince
Dear seniors, I am a rookie who has just started to learn Windows programming and want to port the program in Windows to WINCE. However, I have encountered problems with the OffsetWindowOrgEx function...
ztl7984 Embedded System
MicroPython Getting Started Tutorial - Lesson 1
[i=s] This post was last edited by Chocho on 2017-2-13 09:45 [/i] [align=left]MicroPython Basic Syntax [/align] [b] Table of Contents [/b] Table of Contents.. 1 [/align] Update History.. 2 [/align] In...
Chocho Robotics Development

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 711  1560  1376  1368  1771  15  32  28  36  14 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号