EEWORLDEEWORLDEEWORLD

Part Number

Search

D55342E07B1B18RT0

Description
RESISTOR, THIN FILM, 0.25 W, 0.1 %, 25 ppm, 1180 ohm, SURFACE MOUNT, 1206, CHIP
CategoryPassive components    The resistor   
File Size111KB,4 Pages
ManufacturerVishay
Websitehttp://www.vishay.com
Download Datasheet Parametric View All

D55342E07B1B18RT0 Overview

RESISTOR, THIN FILM, 0.25 W, 0.1 %, 25 ppm, 1180 ohm, SURFACE MOUNT, 1206, CHIP

D55342E07B1B18RT0 Parametric

Parameter NameAttribute value
Is it lead-free?Contains lead
Is it Rohs certified?incompatible
package instructionSMT, 1206
Reach Compliance Codecompliant
ECCN codeEAR99
Other featuresNON-INDUCTIIVE, LASER TRIMMABLE
structureRectangular
Installation featuresSURFACE MOUNT
Number of terminals2
Maximum operating temperature150 °C
Minimum operating temperature-55 °C
Package height0.254 mm
Package length3.2 mm
Package formSMT
Package width1.6 mm
method of packingTR
Rated power dissipation(P)0.25 W
Rated temperature70 °C
GuidelineMIL-PRF-55342
resistance1180 Ω
Resistor typeFIXED RESISTOR
size code1206
surface mountYES
technologyTHIN FILM
Temperature Coefficient25 ppm/°C
Terminal shapeWRAPAROUND
Tolerance0.1%
Operating Voltage100 V
E/H (Military M/D55342)
Vishay Thin Film
QPL MIL-PRF-55342 Qualified Thin Film Resistor Chips
FEATURES
Established reliability, “R” failure rate level (100 ppm), C = 2
High purity alumina substrate 99.6 % purity
Wraparound termination featuring a tenacious adhesion
layer covered with an electroplated nickel barrier layer for
+ 150 °C operating conditions
Very low noise and voltage coefficient
(< - 25 dB, 0.5 ppm/V)
Non-inductive
Laser-trimmed tolerances ± 0.1 %
Wraparound resistance less than 0.010
Ω
typical
In-lot tracking less than 5 ppm/°C
Complete MIL-testing available in-house
Antistatic waffle pack or tape and reel packaging available
Military/aerospace/QPL
SURFACE MOUNT
CHIPS
Actual Size
M55342/02
Thin Film Mil chip resistors feature all sputtered wraparound
termination for excellent adhesion and dimensional
uniformity. They are ideal in applications requiring stringent
performance requirements. Established reliability is assured
through 100 % screening and extensive environmental lot
testing. Wafer is sawed producing exact dimensions and
clean, straight edges.
Note
Specification changed
MIL-PRF-55342
by
DSCC
from
MIL-R-55342
to
CONSTRUCTION
TYPICAL PERFORMANCE
ABS
Passivation
Resistor film
Solder
coating
Nickel barrier
High ourity
alumina substrate
Adhesion layer
TCR
TOL
25
0.1
STANDARD ELECTRICAL SPECIFICATIONS
Test
Material
Absolute TCR
Absolute Tolerance
Stability:
ΔR
Absolute
Voltage Coefficient
Operating Temperature Range
Storage Temperature Range
Noise
Shelf Life Stability
SPECIFICATIONS
Passivated nichrome
± 25 ppm/°C to ± 300 ppm/°C TCR
± 0.1 %
± 0.1 %
± 0.5 ppm/V
- 55 °C to + 125 °C
- 55 °C to + 150 °C
- 25 dB
100 ppm
1 year at + 25 °C
- 55 °C to + 125 °C
+ 25 °C
2000 h at + 70 °C
CONDITIONS
www.vishay.com
50
For technical questions, contact:
thin-film@vishay.com
Document Number: 60018
Revision: 16-Sep-09
F2H_SDRAM Issues
DE1-SoC board, the program uses avalon mm's Burst mode communication, and there are two modules that need to access DDR3, one for reading and one for writing. If both are connected to the f2h_axi_slav...
cncqzxj FPGA/CPLD
NXP MCU development environment installation prompts expiration
Can anyone tell me if there is a crack file for this software? Thanks!...
chenbingjy NXP MCU
Is there something wrong with the development board I bought?
I am working on AD conversion, AC sine wave.But there is a problem: I can convert by only connectingthe ground of the waveform generator, without connecting the signal line. Moreover, I only connected...
aazz Analogue and Mixed Signal
Dual power switching circuit error correction
[i=s]This post was last edited by huiyu2018 on 2016-11-8 16:51[/i] Hi everyone, I am working on a project recently and need a dual power switching circuit. Since using two diodes will result in a larg...
huiyu2018 Power technology
433M wireless positioning
Can I use 433M wireless positioning?...
hinii23 RF/Wirelessly
I'm begging for help from Quartus II and SOPC Builder experts. SOPC Builder opens with an error.
As the title says, I am a beginner in SOPC Builder. I have installed Quartus II and Nios II. Nios II can open Quartus II and complete compilation normally, but when I open SOPC Builder under Quartus I...
DONG1035 Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 321  1679  2865  167  11  7  34  58  4  1 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号