74HC4066; 74HCT4066
Quad single-pole single-throw analog switch
Rev. 7 — 2 April 2013
Product data sheet
1. General description
The 74HC4066; 74HCT4066 is a quad single pole, single throw analog switch. Each
switch features two input/output terminals (nY and nZ) and an active HIGH enable input
(nE). When nE is LOW, the analog switch is turned off. Inputs include clamp diodes. This
enables the use of current limiting resistors to interface inputs to voltages in excess of
V
CC
.
2. Features and benefits
Input levels nE inputs:
For 74HC4066: CMOS level
For 74HCT4066: TTL level
Low ON resistance:
50
(typical) at V
CC
= 4.5 V
45
(typical) at V
CC
= 6.0 V
35
(typical) at V
CC
= 9.0 V
Specified in compliance with JEDEC standard no. 7A
ESD protection:
HBM JESD22-A114F exceeds 2000 V
MM JESD22-A115-A exceeds 200 V
Multiple package options
Specified from
40 C
to +85
C
and
40 C
to +125
C
NXP Semiconductors
74HC4066; 74HCT4066
Quad single-pole single-throw analog switch
3. Ordering information
Table 1.
Ordering information
Package
Temperature range
74HC4066N
74HCT4066N
74HC4066D
74HCT4066D
74HC4066DB
74HCT4066DB
74HC4066PW
74HCT4066PW
74HC4066BQ
74HCT4066BQ
40 C
to +125
C
40 C
to +125
C
TSSOP14
40 C
to +125
C
SSOP14
40 C
to +125
C
SO14
plastic small outline package; 14 leads; body width
3.9 mm
plastic shrink small outline package; 14 leads; body
width 5.3 mm
SOT108-1
SOT337-1
40 C
to +125
C
Name
DIP14
Description
plastic dual in-line package; 14 leads (300 mil)
Version
SOT27-1
Type number
plastic thin shrink small outline package; 14 leads; body SOT402-1
width 4.4 mm
SOT762-1
DHVQFN14 plastic dual in-line compatible thermal enhanced very
thin quad flat package; no leads; 14 terminals;
body 2.5
3
0.85 mm
4. Functional diagram
1
13
4
5
8
6
11
12
1Y
1E
1Z
2
1
13 #
1
2
4
5#
3
8
9
6#
11
12 #
(a)
1
X1
1
X1
1
X1
1
X1
(b)
1
2
2Y
2E
3Y
3E
4Y
4E
2Z
3
13 #
4
5#
1
3
3Z
9
8
6#
11
1
9
10
4Z
1
10
10
12 #
001aad269
001aad270
Fig 1.
Logic symbol
Fig 2.
IEC logic symbol
74HC_HCT4066
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
Rev. 7 — 2 April 2013
2 of 25
NXP Semiconductors
74HC4066; 74HCT4066
Quad single-pole single-throw analog switch
nY
nE
V
CC
V
CC
GND
nZ
001aad271
Fig 3.
Schematic diagram (one switch)
5. Pinning information
5.1 Pinning
terminal 1
index area
1Z
2Z
2Y
2E
2E
3E
GND
5
6
7
001aad268
1Y
1Z
2Z
2Y
1
2
3
4
14 V
CC
13 1E
12 4E
2
3
4
5
6
7
GND
3Y
8
14 V
CC
13 1E
12 4E
11 4Y
10 4Z
9
3Z
4066
11 4Y
10 4Z
9
8
3Z
3Y
V
CC(1)
3E
1
1Y
4066
001aac116
Transparent top view
(1) This is not a supply pin. The substrate is attached to this
pad using conductive die attach material. There is no
electrical or mechanical requirement to solder this pad.
However, if it is soldered, the solder land should remain
floating or be connected to VCC.
Fig 4.
Pin configuration for DIP14, SO14, SSOP14
and TSSOP14
Fig 5.
Pin configuration for DHVQFN14
5.2 Pin description
Table 2.
Symbol
1Z, 2Z, 3Z, 4Z
1Y, 2Y, 3Y, 4Y
GND
1E, 2E, 3E, 4E
V
CC
Pin description
Pin
2, 3, 9, 10
1, 4, 8, 11
7
13, 5, 6, 12
14
Description
independent input or output
independent input or output
ground (0 V)
enable input (active HIGH)
supply voltage
74HC_HCT4066
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
Rev. 7 — 2 April 2013
3 of 25
NXP Semiconductors
74HC4066; 74HCT4066
Quad single-pole single-throw analog switch
6. Functional description
Table 3.
Input nE
L
H
[1]
H = HIGH voltage level;
L = LOW voltage level.
Function table
[1]
Switch
OFF
ON
7. Limiting values
Table 4.
Limiting values
In accordance with the Absolute Maximum Rating System (IEC 60134). Voltages are referenced to GND (ground = 0 V).
Symbol
V
CC
I
IK
I
SK
I
SW
I
CC
I
GND
T
stg
P
tot
Parameter
supply voltage
input clamping current
switch clamping current
switch current
supply current
ground current
storage temperature
total power dissipation
T
amb
=
40 C
to +125
C
DIP14 package
SO14, (T)SSOP14 and DHVQFN14
packages
P
[1]
[2]
Conditions
V
I
<
0.5
V or V
I
> V
CC
+ 0.5 V
V
SW
<
0.5
V or V
SW
> V
CC
+ 0.5 V
V
SW
=
0.5
V to V
CC
+ 0.5 V
[1]
Min
0.5
-
-
-
-
-
65
Max
+11.0
20
20
25
50
50
+150
-
-
Unit
V
mA
mA
mA
mA
mA
C
750
500
mW
power dissipation
per switch
-
100
To avoid drawing V
CC
current out of terminal Z, when switch current flows in terminals Yn, the voltage drop across the bidirectional
switch must not exceed 0.4 V. If the switch current flows into terminal Z, no V
CC
current will flow out of terminals Yn. In this case there is
no limit for the voltage drop across the switch, but the voltages at Yn and Z may not exceed V
CC
or GND.
For DIP14 package: P
tot
derates linearly with 12 mW/K above 70
C.
For SO14 package: P
tot
derates linearly with 8 mW/K above 70
C.
For (T)SSOP14 packages: P
tot
derates linearly with 5.5 mW/K above 60
C.
For DHVQFN14 packages: P
tot
derates linearly with 4.5 mW/K above 60
C.
[2]
74HC_HCT4066
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
Rev. 7 — 2 April 2013
4 of 25
NXP Semiconductors
74HC4066; 74HCT4066
Quad single-pole single-throw analog switch
8. Recommended operating conditions
Table 5.
Recommended operating conditions
Conditions
Min
V
CC
V
I
V
SW
T
amb
t/V
supply voltage
input voltage
switch voltage
ambient temperature
input transition rise
and fall rate
V
CC
= 2.0 V
V
CC
= 4.5 V
V
CC
= 6.0 V
V
CC
= 10.0 V
2.0
GND
GND
40
-
-
-
-
74HC4066
Typ
5.0
-
-
+25
-
1.67
-
-
Max
10.0
V
CC
V
CC
+125
625
139
83
35
Min
4.5
GND
GND
40
-
-
-
-
74HCT4066
Typ
5.0
-
-
+25
-
1.67
-
-
Max
5.5
V
CC
V
CC
+125
-
139
-
-
V
V
V
C
ns/V
ns/V
ns/V
ns/V
Unit
Symbol Parameter
9. Static characteristics
Table 6.
R
ON
resistance per switch for types 74HC4066 and 74HCT4066
V
I
= V
IH
or V
IL
; for test circuit see
Figure 6.
V
is
is the input voltage at a Yn or Z terminal, whichever is assigned as an input.
V
os
is the output voltage at a Yn or Z terminal, whichever is assigned as an output.
For 74HC4066: V
CC
GND = 2.0 V, 4.5 V, 6.0 V and 9.0 V.
For 74HCT4066: V
CC
GND = 4.5 V.
Symbol
R
ON(peak)
Parameter
ON resistance (peak)
Conditions
V
is
= V
CC
to GND
V
CC
= 2.0 V; I
SW
= 100
A
V
CC
= 4.5 V; I
SW
= 1000
A
V
CC
= 6.0 V; I
SW
= 1000
A
V
CC
= 9.0 V; I
SW
= 1000
A
R
ON(rail)
ON resistance (rail)
V
is
= GND
V
CC
= 2.0 V; I
SW
= 100
A
V
CC
= 4.5 V; I
SW
= 1000
A
V
CC
= 6.0 V; I
SW
= 1000
A
V
CC
= 9.0 V; I
SW
= 1000
A
V
is
= V
CC
V
CC
= 2.0 V; I
SW
= 100
A
V
CC
= 4.5 V; I
SW
= 1000
A
V
CC
= 6.0 V; I
SW
= 1000
A
V
CC
= 9.0 V; I
SW
= 1000
A
[2]
[2]
[2]
40 C
to +85
C
Min
-
-
-
-
-
-
-
-
-
-
-
-
Typ
[1]
-
54
42
32
80
35
27
20
100
42
35
20
Max
-
-
-
-
-
-
-
-
-
-
-
-
40 C
to +125
C
Unit
Min
-
118
105
88
-
95
82
70
-
106
94
78
Max
-
142
126
105
-
115
100
85
-
128
113
95
74HC_HCT4066
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2013. All rights reserved.
Product data sheet
Rev. 7 — 2 April 2013
5 of 25
京公网安备 11010802033920号
EEWORLD
