Min. 1,000MΩ (at 500V DC) Measurement at same location as “Breakdown voltage” section.
1,000 Vrms for 1min. (Detection current: 10mA.)
4,000 Vrms for 1min. (Detection current: 10mA.)
Min. 10,000 V
Max. 55°C (By resistive method, nominal voltage applied to the coil, max. switching current.)
Max. 20 ms [20 ms] (Nominal voltage applied to the coil, excluding contact bounce time.)
Max. 20 ms [20 ms] (Nominal voltage applied to the coil, excluding contact bounce time.)
Min. 200 m/s
2
(Half-wave pulse of sine wave: 11 ms; detection time: 10µs.)
Min. 1,000 m/s
2
(Half-wave pulse of sine wave: 6 ms.)
10 to 55 Hz at double amplitude of 2 mm (Detection time: 10µs.)
10 to 55 Hz at double amplitude of 3 mm
Min. 5×10
6
(at 180 times/min.)
Min. 10
5
(at 16A 250V AC): 1 Form C, 1 Form A, 1 Form B
Min. 10
5
(at 10A 250V AC): 2 Form C, 2 Form A, 2 Form B, 1 Form A 1 Form B
Ambient temperature: –40°C to +70°C
–40°F to +158°F
Humidity: 5 to 85% R.H. (Not freezing and condensing at low temperature)
Approx. 14 g
.49 oz
Rating
Surge breakdown
Between contact and coil
voltage*
2
(Initial)
Temperature rise (coil) (at 70°C
158°F)
Operate time [Set time] (at 20°C
68°F)
Release time [Reset time] (at 20°C
68°F)
Functional
Destructive
Functional
Vibration resistance
Destructive
Mechanical
Shock resistance
Electrical (Resistive load)*
3
(at 20 times/min.)
Conditions for operation, transport and storage*
4
Mechanical
characteristics
Expected life
Conditions
Unit weight
Notes: *1. This value can change due to the switching frequency, environmental conditions, and desired reliability level, therefore it is recommended to check this with the
actual load.
*2. Wave is standard shock voltage of
±1.2×50µs
according to JEC-212-1981
*3. In order to obtain the full rated life cycles, the relay should be properly vented by removing the vent nib. More detail, please look at caution for NOTES.
*4. The upper limit of the ambient temperature is the maximum temperature that can satisfy the coil temperature rise value. Refer to Usage, transport and storage
conditions in NOTES.
ASCTB176E 201202-T
Panasonic Corporation
Automation Controls Business Unit
industrial.panasonic.com/ac/e/
DJ (ADJ)
REFERENCE DATA
1. Max. switching capacity
2. Temperature rise
Tested sample: ADJ12024, 6 pcs.
Coil applied voltage: 0%V, Contact current: 16 A, 20 A
Measured portion: Contact, Ambient temperature:
25°C
77°F,
85°C
185°F
100
Temperature rise,
°C
AC resistive load
(1-pole)
40
35
30
25
20
15
10
5
0
10
100
Contact voltage, V
1,000
0
0
5
10
15
20
25
0
90
100
110
120
130
140
3. Coil temperature rise
Tested sample: ADJ56024, 6 pcs.
Coil applied voltage: 100%V, 130%V of rating
Contact current: 0 A, 10 A
Measured portion: Inside the coil, Ambient
temperature: Room temperature, 70°C
158°F
50
Temperature rise,
°C
10A
room temperature
10A 70°C
0A
room temperature
0A 70°C
20
+25°C
+85°C
Contact current, A
40
AC resistive load
(2-pole)
30
10
10
Contact current, A
Coil applied voltage, %V
4. Set and Reset time
Tested sample: ADJ12024, 10 pcs
Coil applied voltage: 80%V, 100%V, 120%V of rating
30
5. Ambient temperature characteristics
Tested sample: ADJ12024, 6pcs
Ambient temperature: –40°C to 85°C
–40°F to 185°F
30
Change rate
to nominal V, %V
20
10
Set
Reset
6. Influence of adjacent mounting
Tested sample: ADJ12024, 6pcs
Ambient temperature: Room temperature
25
20
15
10
5
0
70
Max.
x
Min.
Change rate to nominal V, %V
5
0
–5
Set voltage
OFF
OFF
5
0
–5
OFF
Reset voltage
Set and Reset time, ms
–60 –40 –20
0
20 40 60 80 100
Ambient
temperature,
°C
–10
–20
–30
80
90
100
110
120
130
0
2
4
6
8
10
12
Coil applied voltage, %V
Distance between relays , mm
DIMENSIONS
(mm
inch)
1. 1 Form C, without a test button
CAD Data
The CAD data of the products with a
CAD Data
mark can be downloaded from: http://industrial.panasonic.com/ac/e/
Some time ago, I saw someone in the forum asking about the problem of back-to-back MOS as AC switch. Today, I suddenly thought of this question. When the gate-source voltage is positive and the drain-...
[img]http://i855.photobucket.com/albums/ab112/daition340/MCU/a6892937.jpg[/img] The circuit diagram of the MCU development board I bought shows that PNP is used as a switch. Why does it look wrong to ...
As the title says, I am very helpless. I have just started working in this industry and there is nothing for me to do in the company. I know that my skills are not very proficient. I would like to ask...
Wang Xiaochuan, the "Wudaokou Goalkeeper", is going through a level that he has never gone through before. For example, Sogou's (NYSE: SOGO) financial report, artificial intelligence, and the futur...[Details]
On April 17, the U.S. Department of Commerce suddenly announced that it would completely ban U.S. companies from
selling parts, goods, software and technology
to
ZTE
within 7 years. This als...[Details]
Chip: STM32F107VCT6 Application Pin: THOUSANDS, RMII STM32CubeMX is very convenient to use ETH. The software comes with LWIP and configuration. This time, STM32F107VCT6+DP83848CVV is used. The MII a...[Details]
introduction In the general project development process, two or more microcontrollers are often required to communicate to complete data transmission. For example, a quadcopter wirelessly transmits d...[Details]
I believe that many netizens who have watched "Interstellar" will remember this classic line, "Do not go gentle into this good night, nor let passion be drowned by the gloom of twilight". Different...[Details]
In recent years, in order to meet the needs of social development, more and more companies have entered the fields of smart phones, artificial intelligence,
VR
, AR, etc. After seeing the d...[Details]
sprintf is a function in the C language library that converts data types. There is a situation where In 51 MCU, define unsigned char temp; Then I want to use the serial port to print out temp in deci...[Details]
The analog watchdog of the ADC is used to check if the voltage is out of bounds. It has two upper and lower bounds, which can be set in the registers ADC_HTR and ADC_LTR respectively. The library fun...[Details]
STM32 has 2 watchdogs: independent watchdog and window watchdog. Independent watchdog IWDG: A system fault detector that is independent of the system and is not affected by the system because it has ...[Details]
The calculation formula of the watchdog feeding time (watchdog overflow time) is: Tout=((4*2^prer)*rlr)/40 Tout is the watchdog overflow time (in ms), prer is the watchdog clock prescaler value (...[Details]
6MHz crystal oscillator, using timer counter 1, using interrupt mode, through P1.0 to make a light emitting diode turn on for 100ms, turn off for 300ms, and repeat. Assembly programming is used to ac...[Details]
Please help me analyze the clock cycles occupied by the following delay program. Seek to explain: DELAY: MOV R6, #13 DELAY1: MOV R5, #250 DELAY2: NOP DJNZ R5, DELAY2 DJNZ R6, DEL...[Details]
The isp made a brief summary. Through online programming (the chip is programmed by continuously resetting the chip while the high voltage is converted), the MCU's flash, eeprom, fuse bits, encryptio...[Details]
// 1. Use ICCAVR's terminal debugging window (Terminal) to debug communication. // 2. Set ICCAVR's terminal debugging window and set the serial port to com1 or com2 // The communication baud rat...[Details]
Analog electronics
京公网安备 11010802033920号
EEWORLD
