EEWORLDEEWORLDEEWORLD

Part Number

Search

51724-31100404A0LF

Description
Board Connector, Male, Right Angle, Solder Terminal, Locking,
CategoryThe connector    The connector   
File Size267KB,3 Pages
ManufacturerAmphenol
Websitehttp://www.amphenol.com/
Environmental Compliance
Download Datasheet Parametric View All

51724-31100404A0LF Overview

Board Connector, Male, Right Angle, Solder Terminal, Locking,

51724-31100404A0LF Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
Objectid308917521
Reach Compliance Codecompliant
ECCN codeEAR99
YTEOL0
body width0.574 inch
subject depth0.93 inch
body length3.94 inch
Connector typeBOARD CONNECTOR
Contact to complete cooperationAU ON NI
Contact completed and terminatedGOLD
Contact point genderMALE
Contact materialPHOSPHOR BRONZE
Contact resistance20 mΩ
Contact styleHYBRID
Dielectric withstand voltage2500VDC V
Durability200 Cycles
Filter functionNO
maximum insertion force.973 N
Insulation resistance500000000 Ω
insulator materialGLASS FILLED POLYETHYLENE
Mixed contactsYES
Installation option 1LOCKING
Installation methodRIGHT ANGLE
Installation typeBOARD
Number of connectorsONE
Maximum operating temperature125 °C
Minimum operating temperature-55 °C
Plating thickness30u inch
Rated current (signal)3 A
GuidelineUL
Terminal length0.135 inch
Termination typeSOLDER
Evacuation force-minimum value.17792 N
PDM: Rev:L
STATUS:
Released
Printed: Dec 20, 2010
.
24V AC becomes 30V after bridge rectification, which is a 25% increase. How to solve it?
24V AC becomes 30V after bridge rectification, which is a 25% increase. How to solve it? Do I need to add a capacitor? How big should I add? The motor is a 24V DC motor. Will it burn out if it runs fo...
eeleader Industrial Control Electronics
Using FPGA to make a 100M frequency meter
As the title says,,, hope to discuss with each other ~ thank you...
rongjinzhuo FPGA/CPLD
Joint debugging of proteus and keil
I searched a lot on the internet for methods to debug proteus 7.12 and keil3, but I found that none of them worked for me (the VDM51.DLL file could not be found). After some searching, I finally solve...
香蕉巴拉 DSP and ARM Processors
About the PWM output configuration program of the Hetai HT66F018 chip
Does anyone have C code for PWM output configuration of HT66F018 chip?...
xuanyuanzhu Integrated technical exchanges
[Nucleo experience] + STM32L053 Nucleo + the latest network module W5500 networking
[i=s]This post was last edited by caoqing on 2014-10-10 14:25[/i] Plug in the W5500 module and the network cable to the STM32L053 Nucleo development board. One end of the network cable is connected to...
caoqing stm32/stm8
Why are some components missing when designing a schematic in protelDXP?
Why are there some components missing when designing the schematic diagram in protelDXP? For example, commonly used capacitors and resistors,...
cjx19840106 PCB Design

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1418  204  2867  794  2784  29  5  58  16  57 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号