EEWORLDEEWORLDEEWORLD

Part Number

Search

BTB-49-01-T-S-350

Description
Board Connector, 49 Contact(s), 1 Row(s), Male, Straight, 0.079 inch Pitch, Solder Terminal, Black Insulator, Receptacle
CategoryThe connector    The connector   
File Size292KB,1 Pages
ManufacturerSAMTEC
Websitehttp://www.samtec.com/
Download Datasheet Parametric View All

BTB-49-01-T-S-350 Overview

Board Connector, 49 Contact(s), 1 Row(s), Male, Straight, 0.079 inch Pitch, Solder Terminal, Black Insulator, Receptacle

BTB-49-01-T-S-350 Parametric

Parameter NameAttribute value
Reach Compliance Codecompliant
ECCN codeEAR99
Other featuresPCB STACKING CONNECTOR
body width0.079 inch
subject depth0.25 inch
body length3.871 inch
Body/casing typeRECEPTACLE
Connector typeBOARD CONNECTOR
Contact to complete cooperationSN ON NI
Contact completed and terminatedGOLD
Contact point genderMALE
Contact materialBRASS
contact modeRECTANGULAR
Contact styleSQ PIN-SKT
Dielectric withstand voltage1000VAC V
Insulation resistance5000000000 Ω
Insulator colorBLACK
insulator materialLIQUID CRYSTAL POLYMER (LCP)
Manufacturer's serial numberBTB
Plug contact pitch0.079 inch
Installation methodSTRAIGHT
Installation typeBOARD
Number of connectorsONE
PCB row number1
Number of rows loaded1
Maximum operating temperature105 °C
Minimum operating temperature-65 °C
PCB contact patternRECTANGULAR
Plating thickness150u inch
Rated current (signal)3 A
GuidelineUL
reliabilityCOMMERCIAL
Terminal length0.1 inch
Terminal pitch2.0066 mm
Termination typeSOLDER
Total number of contacts49
Forum posting (editor) now supports the function of directly pasting screenshots!
[size=3]If you want to insert a picture when editing a post, you usually click the "Picture" button, then select a local picture, upload it, and finally click the corresponding picture at the location...
eric_wang Suggestions & Announcements
Stepper motor output waveform problem
The two-phase four-wire stepper motor adopts the eight-beat working mode. Below is the enable signal and input waveformBelow are the two-way output waveform. A and B are both conductiveThe output wave...
Asure1008 stm32/stm8
Battery Power Supply Design (Handout)
Taiwan Self-Strength Foundation class lecture notes DC-DC converter LDO...etc battery power supply design (lecture notes)...
tonytong Power technology
STM32 core Arduino board-ZeroKnow mini board with small size
[i=s]This post was last edited by roc2 on 2019-5-8 00:01[/i] [font=新宋体][size=3][color=rgb(79, 79, 79)]At present, ZeroKnowledge Open Source already has three general development boards - ZeroKnowledge...
roc2 DIY/Open Source Hardware
ARM programming is cumbersome
For ARM programs, such as ARM7, when writing a small project, such as making a light on or a buzzer sound, you need to write a lot of programs, such as initializing GPIO, defining multiple macros, set...
laidawang ARM Technology
What op amp from TI is used for high frequency small signal amplification
[i=s] This post was last edited by dontium on 2015-1-23 11:35 [/i] The signal amplitude is less than 20mvpp, the frequency is 20MHZ, which TI op amp is better to use as the preamplifier. I have opa690...
sw3926 Analogue and Mixed Signal

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1769  2047  1457  1551  215  36  42  30  32  5 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号