026TA28F151A1A1 datasheet, PDF

Datasheet> All Categories > Passive components> The resistor> 026TA28F151A1A1

026TA28F151A1A1: DescriptionFixed Resistor, Wire Wound, 5W, 150ohm, 500V, 10% +/-Tol; CategoryPassive components The resistor; File Size564KB，4 Pages; ManufacturerCTS; Environmental Compliance

Download Datasheet Parametric View All

026TA28F151A1A1 Overview

Fixed Resistor, Wire Wound, 5W, 150ohm, 500V, 10% +/-Tol

026TA28F151A1A1 Parametric

Parameter Name	Attribute value
Is it Rohs certified?	conform to
Reach Compliance Code	unknown
ECCN code	EAR99
structure	Fully Enclosed
Manufacturer's serial number	026(T)
Number of terminals	2
Maximum operating temperature	70 °C
Minimum operating temperature	-10 °C
Package diameter	23.8 mm
Package length	11.9 mm
Package form	Panel Mount
Rated power dissipation(P)	5 W
resistance	150 Ω
Resistor type	FIXED RESISTOR
rotation angle	300 deg
series	026(T)
technology	WIRE WOUND
Tolerance	10%
Operating Voltage	500 V

Preview

Download Datasheet

View All

Series 026

Commercial 15/16"

(24mm) Diameter,

5-Watt, Wirewound

Variable Resistors

•

Fully enclosed construction

•

5-watt power rating

•

Compact size

•

Superior resistance stability

•

Tandem constructions available

•

Economical

•

Bushing or twist tab mounting

•

Available with pull-push and rotary

power switches

•

3% maximum linearity

Electrical and Mechanical Specifications

Resistance Range

Linear: 1 ohm through 25K ohms

Audio: 20 ohms through 10K ohms

Resistance Tolerance

Standard: ±10%

Special: Tighter tolerance available in most

resistance values

Power Rating, Watts

5 watts @25 C, 4watts@55 C, derated to

no load at 105 C, linear taper, bushing

mounted control on steel panel 4" x 4" x .050"

(101.6mm x 101.6mm x 1.27mm).

(Derating required on two section controls.)

Voltage Rating

Bushing to Terminals:

High pot test, one minute --- 1,000 VAC

Operating maximum

--- 500 VDC

Across End Terminals:

350 VDC maximum, load not to exceed

wattage rating.

Operating Temperature

-10 C to +70 C

Resistance Tapers

Standard: Linear, 15% audio

Special: Consult factory

Taps

One tap at 50% of resistance and rotation available

on resistance values under 5K ohms.

Power Switches

Available in most constructions.

Angle of Rotation

Total Rotation:

Without switch --- 300

With switch

--- 300

Effective Rotation:

Without switch --- 280

approximate

With switch

--- 265 approximate

Turning Torque

0.75 to 6.0 IN.OZ. (45 to 360 g-cm)

Stop strength

Typical 8 to 15 Kg-cm (material dependent)

(continued on next page)

Technical Data Sheet 1448C

Technical Data Sheet 10/28/03 Rev A

CTS CORPORATION /

MANUFACTURER OF RELIABLE ELECTRONIC COMPONENTS

Recommended Resources

Electric fan induction braking circuit diagram

Step-down starting control circuit for starting multiple motors one by one

Automatic exhaust fan circuit

Thyristor circuits with output power of 100W, 700w and 1000W

Thyristor control circuit with low supply voltage

Computer motherboard circuit diagram 815 1_01

Confusing Questions: I have never worked on embedded systems. Now I am working on a project based on vs 2005 + wince6.0. I am mainly working on the user interface, which runs on a tablet PC (touch screen). I have not seen...; ssssssss Embedded System

Example of a T-type resistor network inverting input ratiometer: In practical application circuits, in order to increase the input resistance of the inverting input proportional operation circuit, the T-type resistor network in the circuit shown in the figure is of...; 程序天使 Analog electronics

pci9054 cannot be adjusted. I wonder if it is due to FPGA timing delay.: The company has a mature architecture, but it has problems for me. Originally, LCLK was directly given by an external crystal oscillator. I entered the FPGA and then gave the 9054 chip through the FPG...; 流浪的猥琐 FPGA/CPLD

Here is a picture that explains one of the frequency band uses I shared before.: Millimeter waves usually refer to electromagnetic waves with a frequency band of 30~300GHz and a corresponding wavelength of 1~10mm. The operating frequency is between microwaves and far infrared wave...; btty038 RF/Wirelessly

[Problem Feedback] Anlu TangDynasty ChipWatcher clock source selection problem: As far as I understand, ChipWatcher should only allow one clock source to be selected. However, in actual use, it seems that even after selecting multiple ones, there is only one in the end. In this c...; littleshrimp FPGA/CPLD

Please help me~~a small program for intel8051: Store 20 data consecutively at RAM30H, move them to 50H, store and count the total number of 05H in the data block. How to do it in assembly~~Thanks for your advice~~...; mingboal Embedded System

Shortcut: E0 E1 E2 E3 E4 E5 E6 E7 E8 E9 EA EB EC ED EE EF EG EH EI EJ EK EL EM EN EO EP EQ ER ES ET EU EV EW EX EY EZ F0 F1 F2 F3 F4 F5 F6 F7 F8 F9 FA FB FC FD FE FF FG FH FI FJ FK FL FM FN FO FP FQ FR FS FT FU FV FW FX FY FZ G0 G1 G2 G3 G4 G5 G6 G7 G8 G9 GA GB GC GD GE GF GG GH GI GJ GK GL GM GN GO GP GQ GR GS GT GU GV GW GX GZ H0 H1 H2 H3 H4 H5 H6 H7 H8 HA HB HC HD HE HF HG HH HI HJ HK HL HM HN HO HP HQ HR HS HT HU HV HW HX HY HZ I1 I2 I3 I4 I5 I6 I7 IA IB IC ID IE IF IG IH II IK IL IM IN IO IP IQ IR IS IT IU IV IW IX J0 J1 J2 J6 J7 JA JB JC JD JE JF JG JH JJ JK JL JM JN JP JQ JR JS JT JV JW JX JZ K0 K1 K2 K3 K4 K5 K6 K7 K8 K9 KA KB KC KD KE KF KG KH KI KJ KK KL KM KN KO KP KQ KR KS KT KU KV KW KX KY KZ

Popular Components