EEWORLDEEWORLDEEWORLD

Part Number

Search

026TA32R1A8A1A4

Description
Fixed Resistor, Wire Wound, 5W, 1.8ohm, 500V, 10% +/-Tol
CategoryPassive components    The resistor   
File Size564KB,4 Pages
ManufacturerCTS
Environmental Compliance
Download Datasheet Parametric View All

026TA32R1A8A1A4 Overview

Fixed Resistor, Wire Wound, 5W, 1.8ohm, 500V, 10% +/-Tol

026TA32R1A8A1A4 Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
Reach Compliance Codeunknown
ECCN codeEAR99
structureFully Enclosed
Manufacturer's serial number026(T)
Number of terminals2
Maximum operating temperature70 °C
Minimum operating temperature-10 °C
Package diameter23.8 mm
Package length11.9 mm
Package formPanel Mount
Rated power dissipation(P)5 W
resistance1.8 Ω
Resistor typeFIXED RESISTOR
rotation angle300 deg
series026(T)
technologyWIRE WOUND
Tolerance10%
Operating Voltage500 V
Series 026
®
Commercial 15/16"
(24mm) Diameter,
5-Watt, Wirewound
Variable Resistors
Fully enclosed construction
5-watt power rating
Compact size
Superior resistance stability
Tandem constructions available
Economical
Bushing or twist tab mounting
Available with pull-push and rotary
power switches
3% maximum linearity
Electrical and Mechanical Specifications
Resistance Range
Linear: 1 ohm through 25K ohms
Audio: 20 ohms through 10K ohms
Resistance Tolerance
Standard: ±10%
Special: Tighter tolerance available in most
resistance values
Power Rating, Watts
o
o
5 watts @25 C, 4watts@55 C, derated to
o
no load at 105 C, linear taper, bushing
mounted control on steel panel 4" x 4" x .050"
(101.6mm x 101.6mm x 1.27mm).
(Derating required on two section controls.)
Voltage Rating
Bushing to Terminals:
High pot test, one minute --- 1,000 VAC
Operating maximum
--- 500 VDC
Across End Terminals:
350 VDC maximum, load not to exceed
wattage rating.
Operating Temperature
o
o
-10 C to +70 C
Resistance Tapers
Standard: Linear, 15% audio
Special: Consult factory
Taps
One tap at 50% of resistance and rotation available
on resistance values under 5K ohms.
Power Switches
Available in most constructions.
Angle of Rotation
Total Rotation:
o
Without switch --- 300
±
5
With switch
--- 300
o
±
5
Effective Rotation:
Without switch --- 280
o
approximate
o
With switch
--- 265 approximate
Turning Torque
0.75 to 6.0 IN.OZ. (45 to 360 g-cm)
Stop strength
Typical 8 to 15 Kg-cm (material dependent)
(continued on next page)
Technical Data Sheet 1448C
Technical Data Sheet 10/28/03 Rev A
CTS CORPORATION /
MANUFACTURER OF RELIABLE ELECTRONIC COMPONENTS
Power supply design tip 2: Harnessing noisy power supplies
[align=left][color=rgb(85, 85, 85)]Noise-free power supplies are not designed by accident. A good power supply layout is designed to minimize experimentation time. Minutes or even hours spent carefull...
莫妮卡 Analogue and Mixed Signal
[Chuanglong Technology Allwinner A40i Development Board] Building a development environment and Qt development experience based on virtual machine images
Preface The installation based on the SDK file on the CD is cumbersome, and various dependencies are installed, and the build may fail. So in order to avoid wasting too much time on the installation e...
qinyunti Domestic Chip Exchange
SI4432 Direct Mode
Is there any expert who has done Si4432 direct mode and can give me some guidance? I use si4432 for serial port transparent transmission. If I use FIFO mode, when the serial port rate reaches 9600bps,...
morewater RF/Wirelessly
Headhunting position: Engineers to the United States! Contact 13381085719 13381085771 Mr. Liu
Headhunting position: Engineers to the United States! Contact 13381085719 13381085771 Mr. Liu...
张肖肖 Embedded System
A newbie asks a question about data, idata, and xdata
Because some relatively large idata type global variables are defined in the program, the 256 bytes of RAM are not enough. I have selected the small mode. Without considering optimization, can I chang...
a8461813 MCU
Problems with converting evc4 to vc2005
I used evc4 in my ce4.2 system. Now I want to use vc2005 because I can debug in single step. But I can't find a message function. Please tell me how to do it in vc2005. I know evc4 and vc6. Thank you....
张皓翔 Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2281  968  1858  1601  691  46  20  38  33  14 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号