I INCH-POUND
MIL-PRF-83401G
18 March 1996
SUPERSEDING
MIL-PRF-63401F
9 October 1989
PERFORMANCE
SPECIFICATION
“{
RESISTOR NETWORKS, FIXED, FILM,
ANDCAPACITOR-RESISTOR
NETWORKS,CEWIC
CAPACITOR
AND FIXED FILM RESISTORS, GENERALSPECIFICATION
FOR
This specification is approved for use by all Depafl-
menta and Agencies of the Department of Defense.
1.
SCOPE
1.1 -.
Thiss~dfi=tion
mvemthegeneml
requi~menS
tirhemeti@l~
sealed (see3.10) and
nonhermetically sealed networ%
These neWo~smnsist
entim&offixd,
film resistom or, fixed film
resistora andcetarnic capacitora. They areprimary intended forusein electronic drcuite. This
specification hastwopmduct
levels, ahighrehability,
100percent bum-unscreened’’M”
partnumber level
and nonbum-in screened part number level “C (see 1.2.1).
1.2 Qassification.
.
Networks specified herain (see 3.1 ) w“ll be identified by a PIN
1.2.1 partorldua~l.
which will consist of the basic number of the associated specification and ceded number. Each
aaemiated specification covers a different network style. The number will be cded to provide information
mncaming
the level of bum-in screening of the network, characteristic, resistance value, resistance
tolerance, and schematic. The PIN will be in the following form with a caded number derived as indicated:
3L!Q2!2
M83401O1
Associated specification
number (indicating
MIL-PRF-S340W31)
H
Characteristic
(ace 1.2.1.1)
e
Ork f-w
1002
J
be~,
A
Schematic
(sea 1.2.1.4
and 3.1)
—
Resistance
(see 1.2.1.2)
—
Resistance
tolerance
(see 1.2,1.3)
Pfon
bum-in swawd
.
network ~C owl number).
1002
—
—
Realstance
Schematic
Resiatsnca
(ace 1.2.1
.2)
C6340101
Associated
specification
number (mdicsting
H
Charederistic
(see 1.2.1.1)
J
A
MIL-PRFQ401ml
)
toleranca
(see 1.2.1.3)
(ace 1.2.1.4
and 3.1)
Beneficial comments (recommendations,
additions, deletions) and any petinent data which maybe of
use in improving this document should be addressed WDESC-ELDM,
1507 Wilmington Pike,
Dayton, OH 45444-5765 by using the Standardization Document Impmvement Proposal (DD Form
1426) appearing at the end of this document or by letter.
AMSC N/A
PISTRIBUTI ON STATEMEN T A. Approved
FSC 59GP
for public release; distribution
is unlimited.
MI L-P RF-83401G
1.2.1.1 Characteristics.
accordance with table 1.
The characteristics
TABLE
are identified
1, ~
by the single
,.
{,
lettera
C, H, K, M, R, V, or Y in
I
Test or condition
Charaderistiss
I
I
‘nits
Y II
Resisten= temperature
charaderistk
(see 3.13)
Tracking to the referense element
Maximum
ambient temperature
at rated wattage (see 3.5)
Masimum ambient temperature at
zere pawer deratirrg (see figure 2)
Thermal shack (ace 3.7) and
AR
Pewer ccmditioning (see 3.8)
ARafio
Lew temperature operation
AR
(ace 3.14)
ARatio
i5
%a
70
125
*.02
*.01
*O1
+.01
c 1/
%0
i5
70
125
*.25
*.03
*.1O
i..o2
al
Vz
+50
*y
70
125
+.25
*O3
*.1O
Ha
m
41
70
125
MO
51
*.1O
K21
*100
*I
70
125
i.70
g!
*.25
M 1/
S300
51
70
125
*.70
*I
*.50
Rz
ti5
% al
70
125
+.08
*O4
*O3
Masimum
percent
change in
-c
PPMrc
Short time overload
(see 3.15)
Terminal strength
(see
3.16)
Resistance to eeldering
heat (see 3.1 9)
AR
ARatiO
AR
ARatio
AR
ARatio
i..o2
*.01
*.01
i.ol
*.01
*.01
*.1O
*.02
*.1O
*O3
*.1O
*O2
*.1O
i..o2
*1O
i..o3
*1O
4/
*lo
41
*.25
&l
&lo
4/
*.25
ql
*.25
&l
*.25
51
*.50
&
+.25
ql
+.25
+.02
i.03
*.02
i.03
+.02
*.05
resistance
(0.01
ohm
additional
allowed
for
measurement
error)
Moisture resistance
(SSS
3.20)
Shack, specified pulse
(See 3.21)
vibration, high
fraquensy ( see 3.22)
tife
(see 3.23)
AR
ARatio
AR
ARatio
AR
ARati 0
AR
ARati o
i.ol
*.01
*O1
*.01
*.01
*.01
+.05
*.025
*O2
i.20
*.02
k25
*O2
i.20
*O2
+.25
Al
k.to
&l
*.25
ql
i.50
~1
k25
*I
*.50
gl
k25
*.02
i.05
*.02
*.03
and, wlren
appliseble,
nasimum
persent
*.03
*.25
*.03
*.1O
*.03
+.03
+.25
*.03
L1O
*.03
ql
*.25
4/
*50
g
4/
+.25
gl
*SO
4/
&l
*.25
&l
=.0
41
i..o2
*.03
*.02
*.1O
*O3
shange
in
resistense
ratio.
Pewer rating at 25-C
AR
*O5
*.1O
*.1O
*5O
*.50
-.0
*.1O
(ace 3.23.1)
*.03
ARati o *.025
*.03
41
&l
~1
*.03
High temperature
*.01
*.20
AR
*.10
*1O
*.05
*.50
*1.0
i..o3
exposure (see 3.24)
*.03
41
g
g
*.02
ARati 0 +.01
Low
temperature
*.01
*.1O
*.50
*.03
AR
*.10
*IO
k25
storage (see
3.25)
*O2
ARati0
*O1
*.02
4
~1
ql
*.02
Insulation resistenca (see 3.18)
10,OOO 10,OOO 1O,LWO 10,OOO 10,OOO 10,OOO 10.OOQ Megohms
Resistense, tolerance and,
.oo5p4
.1 (B)
.1 (B)
.1 (B)
.5 (D)
1.0(!=) .05(A)
when applicable, msiatance ratio
.Ol(l-)
.5 (D)
.5 (D)
.5 (0)
1.0 (F) 2.O(G ) .1 (B)
* Percent
acswacy
v
.05(A)
1.0 (F) 1,0 (F) 1.0 (F) 2.0 (G) 5.O(J )
.5 (D)
.1 (B)
5.0 (J )
.5 (D)
1.0 (F)
Hermetically sealed resistor network will conform to the requirement specified in 3.10. These units
II
may be furrkhed to meet characteristic H, K, M, and V requirements, ”
~ Nonherrnetically sealed resistor netwoka are those not meeting the requirement
Characteristic H, K, M, R, or V will not be furnished against C requirements.
~1 See 3.9.3.
g/ Not applicable.
of 3,10.1.
MIL-PRF-83401G
1.2.1.2 fiesistanc~,
1.2.1.2.1 Four diait resistance designation (all resistor values eaua l]. The four digit resistance
designation is applicable to
all resistance tolerances,
The nominal
resistance is identified by four digits:
the firat three digita represent significant figures and the last digit specifies the number of zeros to follows.
Vvhen the value of resistance is less than 100 ohms, or when fractional values of an ohm is required, the
“R will be substituted for one of the significant digits to represent the decimal point. When the letter “R is
used, sumeeding digits of the group represent significant figures. The resistance values designations are
shown in fables Il. Standard values for every decade will Wow the sequeuce demonstrated for”1 O to
100 decade in table Ill. Resistance values not listed in fable Ill far the appropriate resistance tolerance
will be considered as not conforming to the specification, The resistance values far tolerances V, T, A and
B may be any value within the timits specified in 3.1, but it is preferred that values be chosen from the “B
(0.1~ and “D (0.5)” mlumns of table Ill.
Although resistance tolerances “G and”~ normally require less than three significant figures to
adequately describe the true resistance value, for the purpose of this specification, the nominal value W
be three significant figures fallowed by the fourth digit to signify the number of zeros to fallow.
ia
ii
II
“ve for ne desianl. The
1.2.1.2.2 ~ ee i i
Th
three digit resistance designation is applicable to tolerances G (f2.O percent) and J (+5.0 percent). The
nominal resiskmce expressed in ohms is identified by three digits the first two digita represent significant
figures and the last digit specifies the number of zeros to fallow. When the value of resistance is less than
10 ohms, or when fractional values of an ohm are required, the letter “R” will be substituted far one of the
significant digits to represent the decimal point. When the letter “R” is used, su-eding
digita of the
group represent signikant figures. The resistance value designations are shown in table IV. The
standard values far every decade w“ll follow the sequence demonstrated for the”1 O to 100” decade in
table Ill. The three digit resistance designation is far Army and Air Form use oniy.
~
TABLE H. D i
i
Joleran ce of 0,10.0.50.1.0,
istance
2.0, and 5.0 Dercant.
Designation
1ROOto 9R88
incl.
10RO
to 98R8
ind,
1000 to 8b80 ind.
Resistance
ohms
1001 to 9881 ind.
1002 to 9882 ind.
1003 to 9883 ind.
1004 to 9SS4 ind.
1.CK1
to
10,0 to
to
1o11
1,000
to
Io,ooo
lCWOO
1,Joo,ooo
9.8a ind.
98.8
ind,
9W
incS.
ind.
ind.
ind.
Incf.
9,880
to
98,800
to 888,000
to 9,880,000
.-
MIL-PRF-83401G
TABLE Ill. Standard resistance
(B)
(D)
10.00
10.10
10.20
10.40
10.50
10.60
10.70
10.90
11.00
11.10
11.30
11.40
11.50
11.70
11.80
12.00
12.10
12.30
12.40
12.60
12.70
12,90
13.00
13.20
13.30
13s0
13.70
13.80
14.00
14.20
14.3a
14.50
14.70
14.90
15,00
15.20
i 5.40
15.60
15.80
10,00
16.20
16,40
16.54
16,70
16.90
17.20
17.40
17.00
17.80
18.00
18.20
(F)
10.00
10.20
10.50
10.70
11.00
11.30
11.50
11.80
12.00 2/
{2.10
12,40
12.70
13.00
13,30
13.70
14,00
14.30
14.70
15,00
15.40
15,80
16.00 Z
16.20
16.50
16.90
17.40
17.an
6.W
18.20
(G)
(J)
00
values for the 10 to 100 decade .1
(B)
(D)
(F)
(B)
(0)
16,40
18,70
16.80
19.10
19.30
19.W
~9,80
20.00
20,30
20.50
20.80
21.00
21.30
21.50
21,80
22.10
22.30
22.ad
22.80
23.20
23.40
23,70
24.00
24,30
24.00
24,90
5.20
5s0
25,80
26.10
26.40
26.70
27.10
27,40
27.70
Za.w
2.9.40
26.70
28.10
29.40
29.80
30.10
30.54
30S0
31.20
31.60
32J3O
32.40
32,80
(Fl
(G)
(J)
($
(8)
(D)
(FI
18.70
19.10
19.60
20,00
20,50
21.00
21,50
33,20
33.80
34.00
34.40
34.80
35.20
35.70
.W
33.2o
34.00
34.60
35.70
,00
58.30
9.LX7 9.00
59.70
60.40 60.40
61,20
61.8Q 61,90
00
62.60
63.40 S3.40
04.20
64.80 64.90
65.70
56.50 66.54
67,30
!30
.W
88,10
69.00
69.80
70,60
71.50
72.30
73.20
74,10
75.00
75.90
76.80
77.70
78.70
79.60
80.W
81.00
82.50
83.50
e-1.ao
85.s0
86.60
86.70
89.80
90.90
S8.lo
69.60
71.50
73,20
75.00
76.80
78.70
60.60
!.00
r.cm
82.50
84.60
86,60
68.70
90.90
I
.00
.W
36.10
36.50 36.W
37.W
37.40 37.40
37.90
38.30 38.341
38.60
!.00
39,20
39.70
40.20
40.70
41.20
41.70
42.20
42.70
43.20
43.70
44,20
44.80
45,30
45.80
4s.40
47.00
47,50
48.10
48.70
49.30
49.60
50.5a
51.10
51.70
52.30
53.00
53.en
54.20
54.80
55.60
39.20
40.20
41,20
42.20
8.00
43.20
44,20
45,30
46.40
47JYI ~
47.50
48.70
48.30
I .00
ml
22,10
zz.ao
23.20
23.70
1.00
ml
24.30
24.60
25.50
26.10
26,70
.W
7.00
ml
27,40
28.00
28.70
MO
51.10
52.30
53.60
54.60
B.OO
26.40
0,00
30.10
30.80
31.60
32,40
92.00 93.10
93,10
94.20 95.30
95.34
88.54 97.60
97.00
98.80
56.20 56,20
56.904
57.60 57.60
W30
pmptiate resblanm
tokranca
I ba constierei as not car
w vdthlnthe h-nitss@7iI
W
3.1,
bu
1/
wt liskd in labb Ill for the
Reaktancaval
u V, T, A, and B may ba any
spedficatbn.
ThOrdStillC5 VdU- b?
tokn
t
pmfermdOlaf
values k chclsml from -B” and ‘D. column of tabk Ill.
Inadive for .&v des~n atfer 9 March 1987.
A
z
I
MI L-PRF-83401G
1.2.1.2.3 Resistance designation for netw ork schemat ics H, J. N. a nd X. For network schematics H, J,
N, and X, the four digit resistance designation becomes a code indicator with the first digit being an “A
and the following three digits a code number indicating a resistance combination described in the
apPkeble associated specification.
TABLE IV. p~ sianator of resi
~
of
nce val
nt. ~1 ~
for resista
Ierances
Designator
5Rlto 9R1 ind.
100 to 910 ind.
101
to911
inst.
102 to 912 ind,
Resistance ohms
5.1
10
100
1,000
to
to
to
9.1 incl.
91.0 ind.
910
ind.
103
to
913 irrd.
104 to 914 ind.
I/
~
9,180 ind.
10,GQO to 91,800 ind.
100,000
to
91O,OQO incl.
to
Three digit resistance designation
Three digit resistance designation
is inactive far new design.
is for Army and Air Force use only.
rsti
1.2.1.3 fl~ sista
in accordance with table V.
toleranca
The resistance
and ratio tolerance is identified by a single letter
TABLE V, &?S istance *
reti‘o toleran~.
Symbol
Resistance tolerance
percent
0.005
0.01
0.05
0.1
0.5
1.0
2.0
5.0
Ratio tolerarua
percant
0.005
0.01
0.05
0.1
0.1
0.5
Applicable
charsderistic
Y
Y
R, Y
C, V, R, Y
C, V, R, Y
C, V, R, Y
v
T
A
B
D
F
G
J
x 1/
1/ The X toleren~
will be as specified in the associated
specification.
1.2.1.4 ~
ti
The networlr schematic will be identified by a single letter in accordance with figure
1, and as specified (see 3.1 ). Dotted lines in the achematice refer to configurations that might have
..
additional resistors,
1.2.1.5 &hemat ic “~. Additional special schematics may be identified aa “X schematics and
described fully in the associated apecificetion.
See figure 1 for schematic “X” method of presentation.
5
京公网安备 11010802033920号
EEWORLD
