EEWORLDEEWORLDEEWORLD

Part Number

Search

DNP-25PYSH-SG

Description
D Type Connector, 25 Contact(s), Male, 0.109 inch Pitch, Solder Terminal, Hole .112-.124, Receptacle
CategoryThe connector    The connector   
File Size151KB,2 Pages
ManufacturerKeltron Connector Company
Download Datasheet Parametric View All

DNP-25PYSH-SG Overview

D Type Connector, 25 Contact(s), Male, 0.109 inch Pitch, Solder Terminal, Hole .112-.124, Receptacle

DNP-25PYSH-SG Parametric

Parameter NameAttribute value
Reach Compliance Codeunknown
ECCN codeEAR99
body width0.496 inch
subject depth0.203 inch
body length2.088 inch
Body/casing typeRECEPTACLE
Contact to complete cooperationAU ON NI
Contact completed and terminatedGOLD
Contact point genderMALE
Contact materialCOPPER ALLOY
contact modeSTAGGERED
Contact resistance20 mΩ
Contact styleRND PIN-SKT
Dielectric withstand voltage500VAC V
Insulation resistance1000000000 Ω
Insulator colorWHITE
insulator materialGLASS FILLED POLYESTER
Manufacturer's serial numberDNP
Plug contact pitch0.109 inch
Match contact row spacing0.112 inch
Installation option 1HOLE .112-.124
Installation methodSTRAIGHT
Installation typeBOARD
PCB row number2
Number of rows loaded2
Maximum operating temperature105 °C
Minimum operating temperature-55 °C
PCB contact patternSTAGGERED
PCB contact row spacing2.8448 mm
Plating thicknessFLASH inch
Rated current (signal)5 A
reliabilityCOMMERCIAL
Shell surfaceYELLOW CHROMATE
Shell materialSTEEL
Terminal length0.181 inch
Terminal pitch2.7686 mm
Termination typeSOLDER
Total number of contacts25
Multisim simulation results are different at different times
Hello everyone, I have not been using multisim simulation software for a long time but I found a problem that the results of simulating the same circuit at different time periods may be different. Has...
wwwlizhencom Analog electronics
Urgent... Need help from an expert regarding DDS signal generator!
I am making a DDS signal generator that can output sine and square waves, high frequency, and I am now drawing the circuit diagram. Has any expert done it? I use 51 and AD9833, 25MHz crystal oscillato...
梧桐梧桐听雨 MCU
The first 32 system I drew
This is my first time drawing a 32-bit minimum system. I don't understand the line width rules very well. Please correct me if I make any mistakes. Thank you. Attached is the file...
反倒是fdsf PCB Design
LPC IRQ interrupt problem
#include#include#define Fosc 11059200 #define Fcclk Fosc*6 #define Fpclk Fcclk/4 #define Baud 9600 unsigned char i; unsigned char flash; void Timer1(void) { T1TC=0x00; if(flash) { IO0CLR=0xFFFFFFFF; f...
zllka Embedded System
Entering the world of single-chip microcomputers (I) [Popularizing single-chip microcomputer knowledge]
[b]Enter the world of single-chip microcomputer (I) [Popularize single-chip microcomputer knowledge] [/b][align=center][font=宋体][size=3][color=#ff0033][b]Basic knowledge of single-chip microcomputers ...
gnkjmcu MCU
Connect the hardware
After analyzing the schematic diagram, the SD card uses the SPI3 driver. For convenience, it is used to drive the ws2812b rgb led, and only its MOSI pin is used.According to the above figure, the MOSI...
dql2016 MEMS sensors

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2018  683  453  1045  1723  41  14  10  22  35 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号