EEWORLDEEWORLDEEWORLD

Part Number

Search

D-SUB-205AK09BSTBBY2

Description
D Type Connector, 9 Contact(s), Female, 0.109 inch Pitch, Solder Terminal, M2.6, Plug
CategoryThe connector    The connector   
File Size124KB,1 Pages
ManufacturerPalPilot
Download Datasheet Parametric View All

D-SUB-205AK09BSTBBY2 Overview

D Type Connector, 9 Contact(s), Female, 0.109 inch Pitch, Solder Terminal, M2.6, Plug

D-SUB-205AK09BSTBBY2 Parametric

Parameter NameAttribute value
Reach Compliance Codecompliant
ECCN codeEAR99
Other featuresROHS COMPLIANT
body width0.492 inch
subject depth0.492 inch
body length1.213 inch
Body/casing typePLUG
Contact to complete cooperationAU ON NI
Contact completed and terminatedTIN OVER NICKEL
Contact point genderFEMALE
Contact materialPHOSPHOR BRONZE
contact modeSTAGGERED
Contact resistance15 mΩ
Contact styleRND PIN-SKT
Dielectric withstand voltage1000VAC V
Insulation resistance3000000000 Ω
Insulator colorBLUE
insulator materialPOLYBUTYLENE TEREPHTHALATE
Manufacturer's serial number205
Plug contact pitch0.109 inch
Match contact row spacing0.112 inch
Installation option 1M2.6
Installation option 2RIVET
Installation methodRIGHT ANGLE
Installation typeBOARD
PCB row number2
Number of rows loaded2
Maximum operating temperature105 °C
Minimum operating temperature-55 °C
PCB contact patternSTAGGERED
PCB contact row spacing2.8448 mm
Plating thicknessFLASH inch
Rated current (signal)3 A
GuidelineUL
reliabilityCOMMERCIAL
Shell surfaceTIN
Shell materialSTEEL
Terminal length0.125 inch
Terminal pitch2.7686 mm
Termination typeSOLDER
Total number of contacts9
A KEIL project downloaded from the Internet, from which file can I directly check which model of MCU is used in this project
I have a question: If I download a KEIL project from the Internet and open it without using KEIL, from which file in the project can I directly check which MCU model is used in the project?...
深圳小花 MCU
Maple driver 18B20
#define ONEWIRE_DQ 27 //OneWire 引脚int OneWire_Reset(int);int OneWire_ReadByte(int, int);int OneWire_ReadBit(int, int);void OneWire_WriteByte(int, int);void OneWire_WriteBit(int, int);int OneWire_DS18B...
ssawee stm32/stm8
ADC sampling inaccuracy may be caused by some interference
When the ADC input is large, the output digital value is correct, but when the input is small, the output is wrong, and the closer to zero, the greater the error. There should be no problem with the c...
jelly_bessie Analog electronics
Modelsim-Altera path issue
I am a beginner in Quartus 2. When I choose ENA RTL Simulation, I get the following message: the path to the location of the executables for the ModelSim-Altera software were not specified or the exec...
飞机_1991 FPGA/CPLD
1N series Zener diode parameters
1N series Zener diode parameters...
zzzzer16 Test/Measurement
The process of WEBENCH design + 300 lumens LED desk lamp powered by 220V AC
1. Enter the WNBENCH homepage, select the "LED" option, fill in the corresponding parameters, click to start AC 50Hz, AC input 220V, ambient temperature 50 degrees, 300 lumens2. Enter the design and s...
常见泽1 Analogue and Mixed Signal

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1457  2362  1436  1197  1421  30  48  29  25  47 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号