ZTTWS6.00MG
1. SCOPE
This specification shall cover the characteristics of the ceramic resonator with the
type ZTTWS6.00MG.
2. PART NO:
PART NUMBER
ZTTWS6.00MG
3. OUTLINE DRAWING AND STRUCTURE
3.1 Appearance: No visible damage and dirt.
3.2 Construction: Leads are soldered on electrode and body is molded by resin.
3.3 Except the chip(ceramic element, ceramic base, capacitance slice), the materials
don’t contain lead.
3.4 Dimensions
CUSTOMER PART NO SPECIFICATION NO
8.5 1.0
3.0 1.0
5.0 0.5
0.5 0.1
5.0
0.5
2.5 0.3
2.5 0.3
0.3 0.1
Iuput
Ground
Output
* EIAJ MONTHLY CODE
http://www.luguang.cn
Email:lge@luguang.cn
ZTTWS6.00MG
4 RATING AND ELECTRICAL SPECIFICATIONS
4.1 RATING
Items
Withstanding Voltage (V)
Insulation Resistance Ri, M
Operating Temperature Range (
Storage Temperature Range (
)
min.
)
100
Content
50 (DC 1min)
100V 1min
-20 +80
-40 +85
Content
6.000
0.5
30
0.3
Oscillation Frequency
drift -25
+85
6V DC
15V p-p
0.3
For Ten Years
4.2 ELECTRICAL SPECIFICATIONS
Items
Oscillation Frequency Fosc MHz
Frequency Accuracy %
Resonant Impedance Ro
Ω
max.
Temperature Coefficient of Oscillation
Frequency
%
max.
Rating Voltage UR
Aging Rate
5 MEASUREMENT
%
V max.
max.
5.1 Measurement Conditions: Parts shall be measured under a condition ( Temp.
20±15 ,Humidity 65±20% R.H.) unless the standard condition(Temp. 25±3
,Humidity 65±5% R.H.) is regulated to measure.
5.2
Test Circuit
IC 1/6TC4069UBP×2
X CERAMIC RESONATOR
C1 C2 30pF(1 20%)
http://www.luguang.cn
Email:lge@luguang.cn
ZTTWS6.00MG
6 PHYSICAL AND ENVIRONMENTAL CHARACTERISTICS
No.
Item
Condition of Test
2
and
Subject the resonator at +40
90%-95% R.H. for 500h, resonator shall be
measured after being placed in natural
conditions for 1h.
5
for
Subject the resonator to +85
500h, resonator shall be measured after
being placed in natural conditions for 1hr.
Performance
Requirements
It shall fulfill the
specifications in
Table 1.
6.1
Humidity
High
Temperature
Exposure
Low
Temperature
Exposure
6.2
6.3
6.4
6.5
6.6
6.7
6.8
It shall fulfill the
specifications in
Table 1.
Subject the resonator to –25
5
for It shall fulfill the
500h, resonator shall be measured after specifications in
being placed in natural conditions for 1h.
Table 1.
Subject the resonator to 25
for 30 min.
It shall fulfill the
followed by a high temperature of +85
Temperature
for 30 min. Cycling shall be repeated 5 specifications in
Cycling
times. Resonator shall be measured after Table 1.
being placed in natural conditions for 1h.
Subject the resonator to vibration for 2h
each in x y and z axis with the amplitude of It shall fulfill the
1.5mm, the frequency shall be varied specifications in
Vibration
uniformly between the limits of 10Hz-55Hz Table 1.
and then resonator shall be measured.
No
visible
Resonator shall be measured after 3 times' damage and it
Mechanical
random dropping from the height of 100cm shall fulfill the
Shock
on concrete floor.
specifications in
Table 1.
Lead terminals are immersed up to 2 mm
Resistance
from resonator’s body in soldering bath of It shall fulfill the
5
for 5s 1s and then resonator specifications in
to Soldering 260
shall be measured after being placed in Table 1.
Heat
natural conditions for 1h
More than 95%
of the terminal
Lead terminals are immersed up to 2mm
surface of the
Solderability from resonator’s body in soldering bath of
resonator shall
250
5
for 2s 0.5s.
be covered with
fresh solder.
http://www.luguang.cn
Email:lge@luguang.cn
ZTTWS6.00MG
6 PHYSICAL AND ENVIRONMENTAL CHARACTERISTICS
6.9
Terminal
Strength
6.9.1 Terminal
Force of 5N is applied to each lead in axial
Pulling
direction for 10s 1s.
When force of 5N is applied to each lead in
6.9.2 Terminal
axial direction,the lead shall folded up 90
Bending
from the axial direction and folded back to
the axial direction. The speed of folding shall
be each 3s.
No
visible
damage and it
shall fulfill the
specifications in
Table 1.
Table 1
Item
Oscillation Frequency Change
fosc/fosc
% max
Resonant Impedance
Ro
max
0.3
Specification after test
Refer to the initial value
30
http://www.luguang.cn
Email:lge@luguang.cn
ZTTWS6.00MG
7 PACKAGE
To protect the products in storage and transportation
requested.
7.1 Section of package
Package is made of corrugated paper with thickness of 0.8cm.Package has 2 inner
packages, each has 20 inner boxes (each box for plastic bag).
7.2 Quantity of package
Per plastic bag
Per inner box
Per inner package
Per package
500 pieces
3 plastic bags
20 inner boxes
2 inner packages
it is necessary to pack
them(outer and inner package).On paper pack, the following requirements are
(60000 pieces of piezoelectric ceramic part)
7.3 Dimensions and Mark
At the end of package, the warning (moisture proof, upward put) should be stick to
it(see below)
300mm
450mm
Belt(2.9m)
Certificate of
proval(1)
Label(1)
Adhesive
tape(1.2m)
Package(1)
Box(2)
Inner box(40)
http://www.luguang.cn
Email:lge@luguang.cn
34
0m
m
京公网安备 11010802033920号
EEWORLD
