EEWORLDEEWORLDEEWORLD

Part Number

Search

BSTCR-132-D-XXX-28-G-200-LT

Description
Board Connector, 64 Contact(s), 2 Row(s), Male, Right Angle, 0.1 inch Pitch, Solder Kinked Leads Terminal, Black Insulator, Receptacle
CategoryThe connector    The connector   
File Size170KB,1 Pages
ManufacturerMajor League Electronics
Websitehttp://www.mlelectronics.com/
Download Datasheet Parametric View All

BSTCR-132-D-XXX-28-G-200-LT Overview

Board Connector, 64 Contact(s), 2 Row(s), Male, Right Angle, 0.1 inch Pitch, Solder Kinked Leads Terminal, Black Insulator, Receptacle

BSTCR-132-D-XXX-28-G-200-LT Parametric

Parameter NameAttribute value
Is it Rohs certified?incompatible
Reach Compliance Codecompliant
ECCN codeEAR99
Other featuresLEAD LENGTH=1.130 INCH
body length3.2 inch
Body/casing typeRECEPTACLE
Connector typeBOARD CONNECTOR
Contact to complete cooperationGOLD (10) OVER NICKEL (50)
Contact completed and terminatedGold Flash (Au) - with Nickel (Ni) barrier
Contact point genderMALE
Contact materialPHOSPHOR BRONZE
contact modeRECTANGULAR
Contact styleSQ PIN-SKT
Insulation resistance5000000000 Ω
Insulator colorBLACK
insulator materialGLASS FILLED POLYESTER
Manufacturer's serial numberBSTCR
Plug contact pitch0.1 inch
Match contact row spacing0.1 inch
Installation methodRIGHT ANGLE
Installation typeBOARD
Number of connectorsONE
PCB row number2
Number of rows loaded2
Maximum operating temperature125 °C
Minimum operating temperature-65 °C
PCB contact patternRECTANGULAR
PCB contact row spacing2.54 mm
Plating thickness10u inch
Rated current (signal)3 A
GuidelineUL
reliabilityCOMMERCIAL
Terminal pitch2.54 mm
Termination typeSOLDER KINKED LEADS
Total number of contacts64
Is there a big difference between CE6 and CE5?
I have no experience with CE and just started learning CE6. I only have a CE5 book. I feel that the book is very different from the actual experience. Of course, it is only about the interface (this i...
04616115 Embedded System
Mitsubishi AC servo spindle drive
This article applies the intelligent AC servo spindle drive system to CNC machining centers, analyzes the principle of the spindle drive system, gives capacity calculation and model selection methods,...
frozenviolet Embedded System
PPP protocol under vxworks
How do I use the PPP protocol? I installed it but don't know how to use it. Can an expert give me some advice? Should I write a communication program on the upper layer of VXWORKS and then include the...
lovertian Real-time operating system RTOS
How to draw w5300 in protel99se?
My recent graduation project uses w5300, but when I use protel99se to design a PCB board, I don't know how to draw that component. I hope you can give me some advice! ! Thank you very much....
天下无名 51mcu
I want to use DSP to control LM75
I use the I/O port of 2812 to simulate the I2C bus to communicate with LM75, but the program displays the wrong result and I can't find the reason. The following is my program. Could any expert give m...
haijingsea Microcontroller MCU
The hard-earned [2009 e-newsletter (pdf)], learn from tiankai001 to create a strong post
First attach tiankai001's post:2010 Electronic Newsletter (PDF version) https://bbs.eeworld.com.cn/thread-98548-1-1.htmlNext is the 2009 e-newsletter, collected from Xianmao :)...
小瑞 MCU

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1973  2687  2549  1322  1174  40  55  52  27  24 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号