EEWORLDEEWORLDEEWORLD

Part Number

Search

WBA-T0303GC-03-9201-BG

Description
Array/Network Resistor, Divider, Thin Film, 0.25W, 9200ohm, 100V, 0.1% +/-Tol, 25ppm/Cel, Surface Mount, 0303, CHIP
CategoryPassive components    The resistor   
File Size484KB,3 Pages
ManufacturerTT Electronics plc
Websitehttp://www.ttelectronics.com/
Download Datasheet Parametric View All

WBA-T0303GC-03-9201-BG Overview

Array/Network Resistor, Divider, Thin Film, 0.25W, 9200ohm, 100V, 0.1% +/-Tol, 25ppm/Cel, Surface Mount, 0303, CHIP

WBA-T0303GC-03-9201-BG Parametric

Parameter NameAttribute value
package instructionCHIP
Reach Compliance Codecompliant
ECCN codeEAR99
structureChip
The first element resistor4600 Ω
Manufacturer's serial numberWBA
Installation featuresSURFACE MOUNT
Network TypeDIVIDER
Number of components2
Number of functions1
Number of terminals6
Maximum operating temperature150 °C
Minimum operating temperature-55 °C
Package length0.762 mm
Package shapeRECTANGULAR PACKAGE
Package formSMT
Package width0.762 mm
method of packingTRAY
Rated power dissipation(P)0.25 W
Rated temperature70 °C
resistance9200 Ω
Resistor typeARRAY/NETWORK RESISTOR
Second/last element resistor4600 Ω
seriesWBA
size code0303
surface mountYES
technologyTHIN FILM
Temperature Coefficient25 ppm/°C
Temperature coefficient tracking2 ppm/°C
Terminal shapeONE SURFACE
Tolerance0.1%
Operating Voltage100 V
Wire Bondable
Ceramic Resistors
WBA Series
High resistor density
Lower stray capacitance
Proven TaNFilm
®
on ceramic technology
IRC’s WBA series wire bondable ceramic resistors are ideally suited for
your most demanding hybrid application. IRC’s TaNFilm
®
tantalum nitride
thin film technology has years of proven stability, reliability and moisture performance.
IRC’s WBA series of ceramic chip resistors offer a wide range of tolerances and temperature coefficients to fit
a variety of hybrid circuit applications. Custom resistance values, sizes and schematics are also available on
request to the factory.
For high performance wire bondable ceramic resistors for hybrid circuit application, specify IRC WBA series
resistors.
Electrical Data
Absolute Tolerance
Ratio Tolerance
Absolute TCR
Tracking TCR
Package Power Rating (@ 70°C)
Rated Operating Voltage
(not to exceed
P x R )
Operating Temperature
Noise
Substrate Material
Substrate Thickness
Bond Pad Metallization
Backside
to ±0.1%
to ±0.05%
to ±25ppm/°C
to ±2ppm/°C
250mW
100V
-55°C to +150°C
<-30dB
99.6% Alumina
0.015˝ ±0.002
(0.381mm ±0.05)
Gold: 30KÅ minimum
Ceramic (gold available)
Physical Data
T0303 - Tapped network
(0.762mm ±0.025)
0.004˝ min
Bond Pads
A subsidiary of
TT electronics plc
0.030˝ ±0.001
(0.762mm ±0.025)
½R
½R
General Note
IRC reserves the right to make changes in product specification without notice or liability.
All information is subject to IRC’s own data and is considered accurate at time of going to print.
© IRC Advanced Film Division
• 4222 South Staples Street • Corpus Christi Texas 78411 USA
Telephone: 361 992 7900 • Facsimile: 361 992 3377 • Website: www.irctt.com
WBA Series Issue January 2009 Sheet 1 of 3
0.030˝ ±0.001
f28335 eCAN communication
I am using a f28335 development board from China Originality. I want to know why the canh and canl of the eCAN module are only 2v when at invisible level. Isn't the can module a standard 2.5v?...
dyp930 DSP and ARM Processors
Quick Learning and Practical Application of Enhanced 80C51 Single-Chip Microcomputer
[i=s]This post was last edited by paulhyde on 2014-9-15 08:57[/i] Good book 0...
3171068906 Electronics Design Contest
IIC study experience and CAT1024/25
For IIC, there are only two lines to control the transmission of data, SDA and SCL. For the study of IIC protocol, we need to master four modes, master transmission, master reception, slave transmissi...
wangfwk ARM Technology
After studying DSP for a while, I feel that embedded software development seems to be all about software issues.
Maybe it's because I used a ready-made test box provided by the school, which has relatively complete functions, and is a DM643 box from Beijing Hezhongda. Since I started learning DSP, I have always ...
daisyquan Embedded System
Connector selection?
1. Connectors are used on every circuit board. How to select connectors? Can anyone upload some information about connectors?2. Please recommend the connectors that meet the following requirements:(1)...
MD2010 MCU
Discussion on push-pull electromagnet
But has anyone used a push-pull electromagnet? The waveform of the push-pull electromagnet measured by the current probe is shown in the figure. When the core is slowly inserted, the difference betwee...
光芒。 Analog electronics

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1700  1852  576  2028  671  35  38  12  41  14 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号