EEWORLDEEWORLDEEWORLD

Part Number

Search

WBA-T0303GG-03-1102-GC

Description
Array/Network Resistor, Divider, Thin Film, 0.25W, 11000ohm, 100V, 2% +/-Tol, 25ppm/Cel, Surface Mount, 0303, CHIP
CategoryPassive components    The resistor   
File Size484KB,3 Pages
ManufacturerTT Electronics plc
Websitehttp://www.ttelectronics.com/
Download Datasheet Parametric View All

WBA-T0303GG-03-1102-GC Overview

Array/Network Resistor, Divider, Thin Film, 0.25W, 11000ohm, 100V, 2% +/-Tol, 25ppm/Cel, Surface Mount, 0303, CHIP

WBA-T0303GG-03-1102-GC Parametric

Parameter NameAttribute value
package instructionCHIP
Reach Compliance Codecompliant
ECCN codeEAR99
structureChip
The first element resistor5500 Ω
Manufacturer's serial numberWBA
Installation featuresSURFACE MOUNT
Network TypeDIVIDER
Number of components2
Number of functions1
Number of terminals6
Maximum operating temperature150 °C
Minimum operating temperature-55 °C
Package length0.762 mm
Package shapeRECTANGULAR PACKAGE
Package formSMT
Package width0.762 mm
method of packingTRAY
Rated power dissipation(P)0.25 W
Rated temperature70 °C
resistance11000 Ω
Resistor typeARRAY/NETWORK RESISTOR
Second/last element resistor5500 Ω
seriesWBA
size code0303
surface mountYES
technologyTHIN FILM
Temperature Coefficient25 ppm/°C
Temperature coefficient tracking2 ppm/°C
Terminal shapeONE SURFACE
Tolerance2%
Operating Voltage100 V
Wire Bondable
Ceramic Resistors
WBA Series
High resistor density
Lower stray capacitance
Proven TaNFilm
®
on ceramic technology
IRC’s WBA series wire bondable ceramic resistors are ideally suited for
your most demanding hybrid application. IRC’s TaNFilm
®
tantalum nitride
thin film technology has years of proven stability, reliability and moisture performance.
IRC’s WBA series of ceramic chip resistors offer a wide range of tolerances and temperature coefficients to fit
a variety of hybrid circuit applications. Custom resistance values, sizes and schematics are also available on
request to the factory.
For high performance wire bondable ceramic resistors for hybrid circuit application, specify IRC WBA series
resistors.
Electrical Data
Absolute Tolerance
Ratio Tolerance
Absolute TCR
Tracking TCR
Package Power Rating (@ 70°C)
Rated Operating Voltage
(not to exceed
P x R )
Operating Temperature
Noise
Substrate Material
Substrate Thickness
Bond Pad Metallization
Backside
to ±0.1%
to ±0.05%
to ±25ppm/°C
to ±2ppm/°C
250mW
100V
-55°C to +150°C
<-30dB
99.6% Alumina
0.015˝ ±0.002
(0.381mm ±0.05)
Gold: 30KÅ minimum
Ceramic (gold available)
Physical Data
T0303 - Tapped network
(0.762mm ±0.025)
0.004˝ min
Bond Pads
A subsidiary of
TT electronics plc
0.030˝ ±0.001
(0.762mm ±0.025)
½R
½R
General Note
IRC reserves the right to make changes in product specification without notice or liability.
All information is subject to IRC’s own data and is considered accurate at time of going to print.
© IRC Advanced Film Division
• 4222 South Staples Street • Corpus Christi Texas 78411 USA
Telephone: 361 992 7900 • Facsimile: 361 992 3377 • Website: www.irctt.com
WBA Series Issue January 2009 Sheet 1 of 3
0.030˝ ±0.001
How to use C# to call the default gprs network connection of CE6.0
I want to write a CE program with two buttons, dial and hang up, to operate the gprs connection, and cmwap also needs to use a proxy. How can I implement it in C#? It would be better if you can be mor...
卖蛋筒 Embedded System
Questions about using an op amp as a comparator - is it possible?
Original: TI Signal Chain Blog Collection - See how an old TI engineer tames precision amplifiers - I have read the first lecture several times, but I still don't understand it. Lecture 1: Using an op...
Leo417love Analogue and Mixed Signal
stc MCU simulates I2C bus to write EEPROM and always reads FF
I am using STC8a8k microcontroller, and want to realize EEPROM reading and writing by simulating I2C bus, but I always feel that nothing is written in, and the result of reading it through serial port...
干就得了 51mcu
Power Issues
Power supply problem, what is 555 used for? ? ? ?...
yeahyouxiang Power technology
Experts teach you how to make your own single-sided PCB
[size=4]During the electronic competition, I needed to use a self-made PCB to improve the anti-interference ability of the circuit. So I studied the PCB thermal transfer technology for a long time. Ac...
ohahaha PCB Design
How to configure I2C1 to work on AM438x processors?
[align=left][color=#000]Question: How to configure I2C1 to work on AM438x processor? [/color][/align][align=left][color=#000]I failed to configure m43x-epos-evm .dts (I2C1 does not work) i2c1_pins: pi...
wbw Microcontroller MCU

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1277  1246  1361  1886  2052  26  28  38  42  41 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号