Liquids and gases compatible with 316/316L Stainless Steel
8
0
-20
-40
-40
10
±0.5
50
+85
+125
+125
14
11
8.4
50
2X
3X
2.7
-0.25
-1
0.008
-1.5
0.1
3.3
3
5.5
1.5
666
333
399A
3CCB
0.25
1
MAX
UNITS
Count Hex
Count Hex
Count Hex
Count Hex
%Span
%Span
%Span
°C
°C
V
mA
MΩ
Rated
Rated
KΩ
%Span/Year
°C
°C
°C
°C
Bits
Bits
ms
9
8
8
5
6
7
1
4
NOTES
1
1
1
1
2
3
Interface Type
Media
–
Pressure
SENSOR SOLUTIONS
///85BSD
05/2018
Page 2
85BSD
Digital Output
Notes
1.
Measured at vacuum for absolute(A), ambient for gage(G) and sealed gage(S). Output is not ratiometric to supply voltage.
2.
Accuracy: combined linearity, hysteresis and repeatability.
3.
Total Error Band: includes calibration errors and temperature effects over the compensated range. See Figure 3.
4.
The deviation from a best fit straight line (BFSL) fitted to the output measured over the compensated temperature range. For errors beyond the compensated
temperature range, See Figure 2.
5.
Between case and sensing element.
6.
2X or 400psi, whichever is less. The maximum pressure that can be applied to a transducer without changing the transducer’s performance
or accuracy.
7.
3X or 600psi, whichever is less. The maximum pressure that can be applied to a transducer without rupture of either the sensing element or transducer.
8.
Maximum temperature range for product with standard cable and connector is -20°C to +105°C.
9.
Start time to data ready is the time to get valid data after POR (Power on Reset). The time to get subsequent valid data is then specified by the response
time specification.
10. Sharp edge strongly recommended for welding applications. Optimum weld parameters will reduce the effect of weld heat on sensor performance. Devices
with lower pressure ranges have greater susceptibility to heat generated during the weld process
11. Device marking:
Each part shall be identified with model number, pressure range, type (‘A’ for absolute or ‘g’ for gage), Lot number, serial number, and data code.
12. Shipping/Packaging Requirements:
each device will be shipped individually packaged in a plastic vial with anti-static foam. For devices without fittings, the stainless steel diaphragm is protected
by a static dissipative cap.
13. Direct mechanical contact with Diaphragm is prohibited. Diaphragm surface must remain free of defects (scratches, punctures, dents, fingerprints, etc) for
device to operate properly. Caution is advised when handling parts with exposed diaphragms. Use protective cap whenever devices are not in use
I want to use the RenamePartition function to rename a partition, but the compilation always fails with the following errors: D:\。 。 。 。 \mount.cpp(339) : error C2018: unknown character '0xa3' D:\。 。 ...
A friend gave me a test board with many components connected to it, including 6 digital tubes, stepper, A/D converter, 4*4 keyboard, and LCD display. But I don't know how to connect these components t...
The YLP2440 board has an application program stored on an SD card, which is over 5M in size. The program starts very slowly during runtime, taking about ten seconds. Can anyone tell me how to increase...
I know that you guys are used to this kind of posts and are somewhat disdainful. You must be thinking: Why didn’t you study hard earlier? I was wrong, but I was also unlucky. The graduation thesis I d...
A vacuum eutectic furnace is a critical piece of equipment used in the manufacturing and processing of various materials, particularly in the fields of microelectronics and nanotechnology. One of t...[Details]
"Have you set your calendar reminder?"
On August 24, Nvidia Robotics' official account posted a photo of a black gift box on a social media platform, with an attached greeting card sig...[Details]
According to foreign media reports, Nissan Motor has recently reached a cooperation with US battery technology company LiCAP Technologies to jointly promote the research and development of next-gen...[Details]
introduction
Sonar imaging is of great significance in marine resource development and defense. Its long range, intuitive display of the observed area, and target identification make it widely...[Details]
Laird Thermal Systems has introduced the HiTemp ET series Peltier cooler modules, which can operate at high temperatures and provide on-site cooling for sensitive electronic devices.
Dig...[Details]
One of the most core components of electric vehicles is the motor. The power supply provides electrical energy to the motor, which converts this electrical energy into mechanical energy, which in t...[Details]
China, August 21, 2025 – STMicroelectronics (NYSE: STM), a world-leading semiconductor company serving a wide range of electronics applications, has published its IFRS 2025 semi-annual financial re...[Details]
introduction
The rapid adoption of computers has led to a growing number of tasks being performed on them. People from all walks of life, especially programmers and writers, are spending incre...[Details]
1. Introduction
In 2015, Apple's new MacBook and Apple Watch both featured force-sensing technology, which Apple calls Force Touch. Each time a user presses the touchpad, the device not only p...[Details]
On August 20, Huawei Device announced that the all-new M7 is the first to feature an in-cabin laser vision solution. This solution offers enhanced active safety capabilities compared to primary vis...[Details]
Most cameras on the market use chips manufactured by Japanese companies like Sony, Sharp, Panasonic, and LG. South Korea now has the capability to produce chips, but the quality is somewhat inferio...[Details]
introduction
A common voltage regulator is a three-terminal one. Its function is to step down the voltage and stabilize it at a fixed output value. Voltage regulators are commonly available in...[Details]
Pure electric vehicles have experienced rapid growth in recent years, and many consumers now consider them as a top choice when purchasing a car. But do you know how to choose a satisfactory and sa...[Details]
The automotive driveshaft is a crucial connecting component in the automotive mechanical system. It is a circular component that allows for connection or assembly, as well as movement and rotation....[Details]
Reasons for the wear of the roller press reducer shaft:
1. Since the expansion sleeve is subjected to a large torque, the mating surfaces of the shaft and the sleeve move relative to each other...[Details]
DSP and ARM Processors
京公网安备 11010802033920号
EEWORLD
