Datasheets are updated as needed and as such, specifications are subject to change without notice. Once printed or downloaded, datasheets are no longer controlled
by Aimtec; refer to www.aimtec.com for the most current product specifications.
2.
Product labels shown, including safety agency certifications on labels, may vary based on the
date manufactured.
3.
Mechanical drawings and specifications are for reference only.
4.
All specifications are measured at an ambient temperature of 25°C, humidity<75%,
nominal input voltage and at rated output load unless otherwise specified.
5.
Aimtec may not have conducted destructive testing or chemical analysis on all internal components
and chemicals at the time of publishing this document. CAS numbers and other limited information are considered proprietary and may not be available for release.
6.
This
product is not designed for use in critical life support systems, equipment used in hazardous environments, nuclear control systems or other such applications which necessitate
specific safety and regulatory standards other the ones listed in this datasheet.
7.
Warranty is in accordance with Aimtec’s standard Terms of Sale available at www.aimtec.com.
When I used the board wizard, I set the following rules to run two lines between two pads. However, after I finished the layout and routed, I found that my board components were a bit dense, and the t...
As the title says, for example, for a two-layer PCB
After copper is applied to both the top GND and the bottom GND
Why do we need to place several vias on the GND copper between the two layers? (After...
There are 10 channels of signals to be tested that need to be output from the serial port to the PC. I connect them to the P0 and P1 ports through 2 latches, and select the data of the P0 and P1 ports...
[align=left][font=Verdana, Arial, Helvetica, sans-serif][size=4][color=#000000]There is one thing I missed before, so I will add it here: [b]There is another module clock source: MODOSC, which generat...
1. Design Overview
1. Design Intent
The rapid development of medical imaging technology continues to promote the progress of modern medicine. CT, MRI, and PET are widely ...[Details]
Magnetic resonance imaging (MRI) systems for medical and scientific applications require a high-performance, high-power inductor capable of establishing a uniform, strong magnetic field. Transverse el...[Details]
With the development of the automobile industry, the complexity and information density of automobile information systems are increasing. Displays are no longer just basic centralized instrument di...[Details]
TD-SCDMA terminal conformance test includes three types of tests: RF index test (reference standard: 3GPPTS34.122), protocol signaling test (reference standard: 3GPPTS34.123) and other tests (refer...[Details]
Today, as network technology becomes more and more popular, industrial field instruments, data acquisition and control equipment are becoming more and more networked, and the combination of industr...[Details]
Industrial control
often requires multi-channel fault detection and multi-channel command control (this multi-task setting is very common). A single CPU chip is difficult to directly complete ...[Details]
1 Introduction
Economic development has prompted people to continuously improve their security awareness. When traditional local analog monitoring methods gradually fail to meet the needs of l...[Details]
After being widely adopted in applications such as backlighting of portable products with small and medium-sized screens, light-emitting diodes (LEDs) have entered the field of general lighting in ...[Details]
Broadcom Corporation announced that its integrated digital TV system-on-chip (SoC) solution, the BCM3549, has been selected by LG Electronics for use in two new broadband high-definition television...[Details]
Temperature measurement and control are extremely important topics in all aspects of industry, agriculture, scientific research, national defense and people's daily life. Temperature measurement sy...[Details]
0 Introduction
In the mixed analog and digital circuit system, multiple power supplies are required. In order to reduce the number of external power supplies and realize the miniaturizatio...[Details]
Hotels are places for domestic and foreign tourists to stay, eat, hold various meetings and banquets. Modern hotels are generally multifunctional and comprehensive, integrating catering, accommodat...[Details]
DigRF is poised to replace the two main forms of data communication paths between RF and baseband semiconductor devices: analog signaling, and proprietary digital signaling (parallel or serial) for...[Details]
The current and future carrier and bandwidth requirements of wireless air interfaces pose a challenge to 3G base station OEMs, who must choose a platform that can quickly meet the processing requir...[Details]
OSRAM Opto Semiconductors publishes complete Life Cycle Assessment (LCA) results for LED lamps, demonstrating their excellent environmental performance
OSRAM's Life Cycle Assessment (LCA) stud...[Details]
PCB Design
京公网安备 11010802033920号
EEWORLD
