EEWORLDEEWORLDEEWORLD

Part Number

Search

LR1108L-18-AA3-A-R

Description
Fixed Positive LDO Regulator, 1.8V, CMOS, PDSO3, SOT-223, 3 PIN
CategoryPower/power management    The power supply circuit   
File Size248KB,7 Pages
ManufacturerUNISONIC TECHNOLOGIES CO.,LTD
Websitehttp://www.unisonic.com.tw/
Environmental Compliance
Download Datasheet Parametric View All

LR1108L-18-AA3-A-R Overview

Fixed Positive LDO Regulator, 1.8V, CMOS, PDSO3, SOT-223, 3 PIN

LR1108L-18-AA3-A-R Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
package instructionSOP, SOT-223
Reach Compliance Codecompliant
ECCN codeEAR99
AdjustabilityFIXED
Nominal dropback voltage 10.3 V
Maximum absolute input voltage7 V
Maximum input voltage7 V
Minimum input voltage2.5 V
JESD-30 codeR-PDSO-G3
Number of functions1
Output times1
Number of terminals3
Working temperatureTJ-Max85 °C
Working temperature TJ-Min-40 °C
Maximum operating temperature125 °C
Minimum operating temperature-40 °C
Maximum output current 11 A
Maximum output voltage 11.854 V
Minimum output voltage 11.746 V
Nominal output voltage 11.8 V
Package body materialPLASTIC/EPOXY
encapsulated codeSOP
Encapsulate equivalent codeSOT-223
Package shapeRECTANGULAR
Package formSMALL OUTLINE
method of packingTR
Certification statusNot Qualified
Regulator typeFIXED POSITIVE SINGLE OUTPUT LDO REGULATOR
surface mountYES
technologyCMOS
Terminal formGULL WING
Terminal locationDUAL
Maximum voltage tolerance3%
UNISONIC TECHNOLOGIES CO., LTD
LR1108
1A FAST ULTRA LOW
DROPOUT LINEAR
REGULATOR
DESCRIPTION
CMOS IC
The UTC
LR1108
operate from a +2.5V ~ +7.0V input supply
as fast ultra low-dropout linear regulators. Wide output voltage
range options are available. The fast response characteristic to
make UTC
LR1108
suitable for low voltage microprocessor
application. The low quiescent current operation and low dropout
quality caused by the CMOS process.
The UTC
LR1108
has ultra low dropout voltage
300mV at 1A load current typically.
The ground pin current is typically 200uA at 1mA load current.
ERROR Flag: When the output voltage drops 10% below
nominal value Error flag goes low.
Output Voltage Precision: Multiple output voltage options are
available and ranging from 1.2V ~ 5.0V at room temperature with
a guaranteed accuracy of ±1.5%, and ±3.0% when varying line,
load and temperature.
FEATURES
* Ultra Low Dropout Voltage
* Low Ground Pin Current
* 0.04% Load Regulation
* The Guaranteed Output Current is 1A DC
* Output Voltage Accuracy ± 1.5%
* ERROR Flag Indicates Output Status
* Low Output Capacitor Required
* Over temperature Protection And Over current Protection
ORDERING INFORMATION
Ordering Number
Lead Free
Halogen Free
LR1108L-xx-AA3--R
LR1108G-xx-AA3--R
LR1108L-xx-AB3--R
LR1108G-xx-AB3--R
LR1108L-xx-TN3--R
LR1108G-xx-TN3--R
LR1108L-xx-AF5-R
LR1108G-xx-AF5-R
Package
SOT-223
SOT-89
TO-252
SOT-25
Pin Assignment
A: GOI
C: GIO
D: IGO
I
G
SD
ERROR
Packing
Tape Reel
O
www.unisonic.com.tw
Copyright © 2013 Unisonic Technologies Co., Ltd
1 of 7
QW-R102-031.M
51 MCU Elf, it is said that you can program even if you don't know MCU
[i=s] This post was last edited by paulhyde on 2014-9-15 09:05 [/i] 51 MCU Wizard, it is said that even if you don't know MCU, you can still program. In fact, it is a collection of small tools. I took...
open82977352 Electronics Design Contest
Question: The handset of a telephone is 130 ohms. I have set up a telephone board. How can I modify the headphone circuit so that I can use 30 ohm headphones?
The phone chip used is TEA1062, SPK is connected to the headset through capacitor C; there is a resistor R between SPK and GAR. The test found that: when R = 100K, C = 1UF, the quality of the telephon...
zfnlj Embedded System
pwm brushless ESC N5065 motor
I bought an fvt brushless ESC, an N5065 motor, and used the PWM driver of STM32. Set the throttle range according to the instructions: ****************************************** First turn off the ESC...
liuw2010 Electronics Design Contest
Problems with converting VHDL integer to real
I want to convert integer type signal to real type. The program is as follows. This program reports an error in maxplus II: file standard.vhdl:Unsupported feature error:floating is not supported An er...
力量 Embedded System
XILINX EDK: Get data from the serial port
Hello everyone! I'm learning Xilinx EDK recently, and I'd like to ask you a question. First of all, the board I'm using is ML506, and the software is EDK 11.1. There is a "hello world" program in the ...
applelonger FPGA/CPLD
Breakpoint setting in CCS3.3
1. If breakpoints cannot be set during simulation under CCS3.3. You need to check your project configuration. Open Build Optins, and in Basic under the Complier dialog box, set Generate Debug to Full ...
ltbytyn Microcontroller MCU

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 698  2916  958  1753  863  15  59  20  36  18 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号