EEWORLDEEWORLDEEWORLD

Part Number

Search

54121-804-20-0950

Description
Board Connector, 20 Contact(s), 1 Row(s), Male, Straight, 0.1 inch Pitch, Solder Terminal, Locking, Black Insulator, Receptacle
CategoryThe connector    The connector   
File Size101KB,1 Pages
ManufacturerAmphenol
Websitehttp://www.amphenol.com/
Download Datasheet Parametric View All

54121-804-20-0950 Overview

Board Connector, 20 Contact(s), 1 Row(s), Male, Straight, 0.1 inch Pitch, Solder Terminal, Locking, Black Insulator, Receptacle

54121-804-20-0950 Parametric

Parameter NameAttribute value
Is it Rohs certified?incompatible
Objectid305692693
Reach Compliance Codecompliant
ECCN codeEAR99
body width0.094 inch
subject depth0.374 inch
body length2 inch
Body/casing typeRECEPTACLE
Connector typeBOARD CONNECTOR
Contact to complete cooperationAU ON NI
Contact completed and terminatedTin/Lead (Sn/Pb) - with Nickel (Ni) barrier
Contact point genderMALE
Contact materialPHOSPHOR BRONZE
contact modeRECTANGULAR
Contact styleSQ PIN-SKT
Insulation resistance5000000000 Ω
Insulator colorBLACK
insulator materialTHERMOPLASTIC
JESD-609 codee0
Manufacturer's serial number54121
Plug contact pitch0.1 inch
Installation option 1LOCKING
Installation methodSTRAIGHT
Installation typeBOARD
Number of connectorsONE
PCB row number1
Number of rows loaded1
Maximum operating temperature125 °C
Minimum operating temperature-65 °C
PCB contact patternRECTANGULAR
Plating thickness15u inch
Rated current (signal)3 A
GuidelineUL, CSA
reliabilityCOMMERCIAL
Terminal length0.095 inch
Terminal pitch2.54 mm
Termination typeSOLDER
Total number of contacts20
PDM: Rev:G
STATUS:
Released
Printed: Mar 10, 2011
.
Is it the inverter or the integrator circuit?
As shown The input Uin of the op amp is obtained from the -380VDC bus through resistor voltage division to obtain -3.5VDC Is the op amp in the figure a simple inverting 1:1 amplifier circuit, or is it...
shaorc Analog electronics
How to configure uclinux to automatically obtain an ip after arm is powered on?
How to configure uclinux to let arm automatically get ip after power on? My development board is S3C44B0. I heard that uclinux supports dhcp. 1. What should I choose when compiling uclinux 2.4 kernel ...
wawj1819 Linux and Android
Can first-tier devices do the job?
Previously, the sensor head was made by Honeywell combined with first-line devices. The SHT21 may be smaller in size. The I2C interface direct cable transmission requires signal preprocessing. Can fir...
bjwl_6338 DIY/Open Source Hardware
linux-2.6.34 kernel porting documentation [simple operation]
I just transplanted the kernel image file, put it on the development board and ran it for a while, and the system is running!!! Pictures speak louder than words...See the attached documentation for th...
37°男人 Embedded System
Introduction to the training for the 2013 Electronic Design Competition
[i=s] This post was last edited by paulhyde on 2014-9-15 03:11 [/i] Nanhua University Huang Zhiwei prepares for the 2013 Electronic Design Competition - Introduction to some information on training...
黄智伟 Electronics Design Contest
Please tell me about the assembly instructions related to AVR program jump
I've been working on the assembly of AVR recently and encountered some problems. I'd like to ask enthusiastic netizens to help me figure out what's going on. The development board I have is atmega128a...
lr2131 Microchip MCU

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2740  2199  1704  2788  986  56  45  35  57  20 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号