EEWORLDEEWORLDEEWORLD

Part Number

Search

D55342E07B91K0CTS

Description
RESISTOR, THIN FILM, 0.25 W, 5 %, 25 ppm, 91000 ohm, SURFACE MOUNT, 1206, CHIP
CategoryPassive components    The resistor   
File Size111KB,4 Pages
ManufacturerVishay
Websitehttp://www.vishay.com
Download Datasheet Parametric View All

D55342E07B91K0CTS Overview

RESISTOR, THIN FILM, 0.25 W, 5 %, 25 ppm, 91000 ohm, SURFACE MOUNT, 1206, CHIP

D55342E07B91K0CTS Parametric

Parameter NameAttribute value
Is it lead-free?Contains lead
Is it Rohs certified?incompatible
Objectid1761485843
package instructionSMT, 1206
Reach Compliance Codecompliant
ECCN codeEAR99
Other featuresNON-INDUCTIVE
structureRectangular
Installation featuresSURFACE MOUNT
Number of terminals2
Maximum operating temperature150 °C
Minimum operating temperature-55 °C
Package height0.254 mm
Package length3.2 mm
Package formSMT
Package width1.6 mm
method of packingTR
Rated power dissipation(P)0.25 W
Rated temperature70 °C
GuidelineMIL-PRF-55342
resistance91000 Ω
Resistor typeFIXED RESISTOR
size code1206
surface mountYES
technologyTHIN FILM
Temperature Coefficient25 ppm/°C
Terminal shapeWRAPAROUND
Tolerance5%
Operating Voltage100 V
E/H (Military M/D55342)
Vishay Thin Film
QPL MIL-PRF-55342 Qualified Thin Film Resistor Chips
FEATURES
Established reliability, “R” failure rate level (100 ppm), C = 2
High purity alumina substrate 99.6 % purity
Wraparound termination featuring a tenacious adhesion
layer covered with an electroplated nickel barrier layer for
+ 150 °C operating conditions
Very low noise and voltage coefficient
(< - 25 dB, 0.5 ppm/V)
Non-inductive
Laser-trimmed tolerances ± 0.1 %
Wraparound resistance less than 0.010
Ω
typical
In-lot tracking less than 5 ppm/°C
Complete MIL-testing available in-house
Antistatic waffle pack or tape and reel packaging available
Military/aerospace/QPL
SURFACE MOUNT
CHIPS
Actual Size
M55342/02
Thin Film Mil chip resistors feature all sputtered wraparound
termination for excellent adhesion and dimensional
uniformity. They are ideal in applications requiring stringent
performance requirements. Established reliability is assured
through 100 % screening and extensive environmental lot
testing. Wafer is sawed producing exact dimensions and
clean, straight edges.
Note
Specification changed
MIL-PRF-55342
by
DSCC
from
MIL-R-55342
to
CONSTRUCTION
TYPICAL PERFORMANCE
ABS
Passivation
Resistor film
Solder
coating
Nickel barrier
High ourity
alumina substrate
Adhesion layer
TCR
TOL
25
0.1
STANDARD ELECTRICAL SPECIFICATIONS
Test
Material
Absolute TCR
Absolute Tolerance
Stability:
ΔR
Absolute
Voltage Coefficient
Operating Temperature Range
Storage Temperature Range
Noise
Shelf Life Stability
SPECIFICATIONS
Passivated nichrome
± 25 ppm/°C to ± 300 ppm/°C TCR
± 0.1 %
± 0.1 %
± 0.5 ppm/V
- 55 °C to + 125 °C
- 55 °C to + 150 °C
- 25 dB
100 ppm
1 year at + 25 °C
- 55 °C to + 125 °C
+ 25 °C
2000 h at + 70 °C
CONDITIONS
www.vishay.com
50
For technical questions, contact:
thin-film@vishay.com
Document Number: 60018
Revision: 16-Sep-09
How to understand the scanning pixels of embedded arm LCD in this sentence
An LCD panel has a resolution of 320×240. The controller will output a line sync signal every time it outputs 320 pixels. After every 240 lines, it should output a frame sync signal. If it is a 4-bit ...
王少永 ARM Technology
Regarding the heating problem of filter capacitor in RC step-down
I am now using RC to make a switch, and the load is a relay. The following is a diagram of RC . When unloaded, the filter capacitors C2 and C1 are hot, the temperature is about 40-50 degrees, and the ...
galaxing008 Analog electronics
Reverse recovery process of rectifier diode
1. The diode has a reverse recovery process from forward conduction to cutoffAdd an input voltage as shown in the figure below to the silicon diode circuit shown in the figure above. During the time 0...
火辣西米秀 Analogue and Mixed Signal
Low-level error: ESP32 official routine compilation failed just because the folder name uses spaces
Today, when I was using the ESP32 official program, the following error occurred. I searched for a long time but couldn't find the reason. Later, I recreated the routine in another folder and compiled...
littleshrimp Domestic Chip Exchange
AVR uses protues to simulate serial communication problems
When AVR uses protues to simulate serial port communication, the following error is always prompted: invalid opcode oxffff at PC=0x0036. Is there any master who can help me solve this problem? Thank y...
zhangjun1960 Microchip MCU
【Help】Please help
Could you please tell me how the buffer value is obtained in the following TI example? According to the manual, for example, "0" displays "segment a+b+c+d+e+f", which should be 0xEB?#includeconst char...
SAI20052005 Microcontroller MCU

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1713  1656  30  639  294  35  34  1  13  6 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号