EEWORLDEEWORLDEEWORLD

Part Number

Search

PTN1005E1960FGT

Description
Fixed Resistor, Thin Film, 0.25W, 196ohm, 100V, 1% +/-Tol, -25,25ppm/Cel, 1105,
CategoryPassive components    The resistor   
File Size98KB,4 Pages
ManufacturerVishay
Websitehttp://www.vishay.com
Environmental Compliance
Download Datasheet Parametric View All

PTN1005E1960FGT Overview

Fixed Resistor, Thin Film, 0.25W, 196ohm, 100V, 1% +/-Tol, -25,25ppm/Cel, 1105,

PTN1005E1960FGT Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
Reach Compliance Codecompliant
ECCN codeEAR99
structureChip
JESD-609 codee4
Number of terminals2
Maximum operating temperature125 °C
Minimum operating temperature-55 °C
Package height0.609 mm
Package length2.667 mm
Package formSMT
Package width1.27 mm
method of packingTR
Rated power dissipation(P)0.25 W
resistance196 Ω
Resistor typeFIXED RESISTOR
seriesPTN
size code1105
technologyTHIN FILM
Temperature Coefficient-25,25 ppm/°C
Terminal surfaceGold (Au) - with Nickel (Ni) barrier
Tolerance1%
Operating Voltage100 V
PTN
Vishay Thin Film
Commercial Thin Film Chip Resistors
FEATURES
Lead (Pb)-free or Sn/Pb terminations available
Moisture resistant
High purity alumina substrate
Non-standard values available
Will pass + 85 °C, 85 % relative humidity and
10 % rated power
100 % visual inspected per MIL-PRF-55342
Very low noise and voltage coefficient (< - 30 dB)
Non-inductive
Laser-trimmed tolerances to ± 0.1 %
Wraparound resistance less than 10 mΩ
Epoxy bondable termination available
Compliant to RoHS directive 2002/95/EC
Actual Size
1505
SURFACE MOUNT
CHIPS
These chip resistors are available in both “top side” and
“wraparound” termination styles in a variety of sizes. They
incorporate self passivated, enhanced Tantalum Nitride
films, to give superior performance on moisture resistance,
voltage coefficient, power handling and resistance stability.
The terminations consist of an adhesion layer, a leach
resistant nickel barrier, and solder coating. This product will
out-perform all requirements of characteristic E of
MIL-PRF-55342.
CONSTRUCTION
Passivation
Tantalum
Nitride
Resistive Film
Solder
Coating
Nickel
Barrier
High Purity
Alumina Substrate
Adhesion Layer
TYPICAL PERFORMANCE
ABS
TCR
TOL
25
0.1
STANDARD ELECTRICAL SPECIFICATIONS
TEST
Material
Absolute TCR
Absolute Tolerance
Operating Temperature Range
Noise
CASE SIZE
0402
0502
0505
0603
0805
(1)
, 0705
(1)
1005
1010
1206
1505
2208
2010
2512
POWER RATING (mW)
50
100
150
150
200
250
500
400
400
750
800
1000
SPECIFICATIONS
Tantalum nitride
± 25 ppm/°C, ± 50 ppm/°C, ± 100 ppm/°C
± 1.0 %, ± 0.5 % and ± 0.1 %
- 55 °C to + 125 °C
< - 30 dB
MAX. WORKING VOLTAGE
75
75
75
75
100
100
150
200
150
150
200
200
RESISTANCE RANGE (Ω)
20 to 35K
20 to 65K
20 to 130K
10 to 80K
10 to 301K
10 to 301K
50 to 600K
10 to 1M
10 to 1M
10 to 1.75M
10 to 2M
10 to 3M
- 55 °C to + 125 °C
+ 25 °C
CONDITIONS
Note
(1)
0705 and 0805 are the same (only use 0805 when ordering)
* Pb containing terminations are not RoHS compliant, exemptions may apply
Document Number: 60026
Revision: 02-Nov-09
For technical questions, contact:
thin-film@vishay.com
www.vishay.com
55
What is the live measurement method in PCB circuit board maintenance?
The live measurement method mainly solves two problems. One is to subdivide the problems found and finally lock them to the components with problems. The other is that if the problem has not been solv...
草房子的新生 PCB Design
Analyze the problems that may arise in daily use of infrared cameras
Red burst problem Some manufacturers promote whether they can produce infrared lamps without red burst as a technical issue, as if red burst means low technology and no red burst means high technology...
xyh_521 Industrial Control Electronics
Chapter 3 General GPIO Operation of MSP-EXP430F5529LP
I. Simple operation of general I/O Refer to MSP430X5XX datasheet.pdf 1.1 Introduction to I/O Features: l Multiple multiplexing and settings (i.e., whether to control input, output, whether to connect ...
shmily53 Microcontroller MCU
After FIR filtering, the number of points increases. How to select points to calculate RMS?
Assuming the number of sampling points is 16 and the number of filter coefficients is 17, the number of points after FIR digital filtering should be 16+17-1=32 points. I want to calculate the effectiv...
alice84 Embedded System
C language learning notes
[i=s]This post was last edited by dochance on 2015-3-24 22:04[/i] [size=6]GCC's processing process:[/size] [size=4]1. Preprocessing This stage is used to process all preprocessing instructions. [/size...
dochance Programming Basics
Implementation of soft subtitles in embedded systems (ARGB1555) Application of freetype
[i=s] This post was last edited by 37°Man on 2014-6-26 14:10[/i] [font=Microsoft YaHei][size=4]I haven't written notes for a long time, so I'll organize some information and share it with you[/size][/...
37°男人 DSP and ARM Processors

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1713  2045  2352  1644  945  35  42  48  34  20 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号