TMP135 Series
TRUMPower
FEATURES
•
•
•
•
•
•
•
90~264 VAC Input, Soft Start
0.98 Active Power Factor
87% to 91% Efficiency
High Peak Power
Low Safety Ground Leakage Current
Class I & Class II Models Available
CEC & Energy Star Level V Compliance
120-135 Watts Medical & ITE Power Adapters
INPUT SPECIFICATIONS
Input Voltage Range ............ 90~264 VAC
Input Frequency ................... 47~63Hz
Input Current ........................ 1.60A rms @ 115 VAC
0.80A rms @ 230 VAC
Inrush Current ..................... 80A @ 115 VAC or 160A @ 230 VAC,
at 25°C cold start
Soft Start ............................... Yes
Earth Leakage Current ........ 200µA max. @ 264 VAC, 63Hz
Touch Current ...................... 100µA max. @ 264 VAC, 63Hz
MODELS LIST
Product N o.
TMP135-12
TMP135-13
TMP135-15
TMP135-18
TMP135-20
TMP135-24
(1)
Output
Voltage
12V
13V
14~16V
18~19V
20~21V
24~25V
28~29V
30~32V
36~38V
46~50V
Maximum
C urrent
10.0A
9.23A
9.29A
7.50A
6.75A
5.63A
4.83A
4.50A
3.75A
2.94A
Peak
(2)
C urrent
20.0A
18.5A
18.6A
15.0A
13.5A
11.3A
5.8A
5.4A
4.5A
3.5A
Maximum
P o w er
120W
120W
130W
135W
135W
135W
135W
135W
135W
135W
OUTPUT SPECIFICATIONS
Output Power Ratings .......... See table
Minimum Load ...................... Not required
Tolerance ............................. ±5%
Ripple and Noise* ............... 1% peak to peak max. at full load
Overvoltage Protection ........ Set at 115-140% of its nominal
output voltage
Overcurrent Protection ........ Protected to short-circuit
conditions
Temperature Coefficient ..... ±0.04%/°C max.
Transient Response ........... Max. excursion of 4% or better on
all models, recovering to 1% of
final value within 500 us after a
25% step load change
* Measured with 20MHz bandwidth at rated line voltage and output load ranges, with
a 10µF tantalum capacitor in parallel with a 0.1µF ceramic capacitor in parallel
across the output.
TMP135-28
TMP135-30
TMP135-36
TMP135-48
Notes:
1) The listed P/N's are for Class I models equipped with IEC 320/C14 AC inlet.
Add suffix "C2" to order Class II models equipped with IEC 320/C18 AC inlet.
When ordering 14-50V output units, specify the requested voltage, e.g. use P/N
TMP135-18.5-C2 to order 18.5V Class II model.
2) The peak current is for 10 seconds maximum with the average power not over the
maximum power.
STANDARDS & COMPLIANCES
EN 55011, EN 55022 ........ Class B, conducted & radiated
FCC, VCCI ......................... Class B, conducted & radiated
EN 61000-3-2 .................... Harmonic distortion, Class A & D
EN 61000-3-3 .................... Line flicker
EN 61000-4-2 .................... ESD, ±8 KV air and ±6 KV contact
EN 61000-4-3 .................... Radiated immunity, 3V/m
EN 61000-4-4 .................... Fast transient/burst, ±2 KV
EN 61000-4-5 .................... Surge, ±1 KV diff., ±2 KV com.
EN 61000-4-6 .................... Conducted immunity, 3 Vrms
EN 61000-4-8 .................... Magnetic field immunity, 3A/m
EN 61000-4-11 .................. Voltage dip immunity,
30% reduction for 500ms,
60% reduction for 100ms,
>95% reduction for 10ms
Safety Standards ............... UL/IEC/EN 60601-1 (3
rd
Edition),
ANSI/AAMI ES 60601-1 (1
st
Edition),
CSA C22.2 No. 60601-1 (2
nd
Edition),
IEC/EN 60950-1 (2
nd
Edition)
Agency Approvals .............. UL, cUL, TUV, CE, CB
Other Compliances .......... RoHS, CEC & Energy Star Level V
* Class I models certified to medical and ITE safety standards; Class II models
certified to medical standard only.
GENERAL SPECIFICATIONS
Power Factor ....................... 0.98 typical @ 115 VAC
Efficiency ............................. 87% minimum at full load
Hold-up Time ....................... 15ms at 110 VAC
Switching Frequency ........... 90~160KHz
Operating Temperature ...... 0 °C to +60°C
Derating ............................... Derate from 100% at +40°C linearly
to 50% at +60°C
Storage Temperature .......... -40°C to +85°C
Relative Humidity ................ 5°C to +95°C non-condensing
Withstand Voltage ............... 4000 VAC from input to output
1500 VAC from input to ground
500 VAC from output to ground
MTBF .................................... 150K hours minimum at full load,
25°C ambient, calculated per
MIL-HDBK-217F
Tumbler Technologies + TRUMPower
3350 Scott Blvd., Building 13 • Santa Clara, California 95054, USA
•
408-988-6616
•
sales@trumpower.com • www.TRUMPower.com
TMP135 Series
120-135 Watts Medical & ITE Power Adapters
MECHANICAL SPECIFICATIONS
The length of output cable for 12V to 16V
output models is 37.4 [950].
Unit: inch [mm]
Tolerance: 0.02 [0.5] maximum
D C OU TPU T C ON N EC TOR
PIN
1
2
3
4
S H E LL
FU N C TION
RETURN
+V
RETURN
+V
AC GND /*NC
*Shell i s NC on class II models
Output connector: Kycon P/N KPPX-4P 4-pin circular DIN or equivalent.
Mating connector: Kycon P/N KPJX-4S-S or equivalent
Contact TRUMPower for output connector options.
#TMP135-2011-0425-1
Tumbler Technologies + TRUMPower
3350 Scott Blvd., Building 13 • Santa Clara, California 95054, USA
•
408-988-6616
•
sales@trumpower.com • www.TRUMPower.com
Test/Measurement
京公网安备 11010802033920号
EEWORLD
