EEWORLDEEWORLDEEWORLD

Part Number

Search

54112-412-44-2400

Description
Board Connector, 44 Contact(s), 2 Row(s), Male, Straight, 0.1 inch Pitch, Solder Terminal, Locking, Black Insulator, Receptacle
CategoryThe connector    The connector   
File Size67KB,1 Pages
ManufacturerAmphenol
Websitehttp://www.amphenol.com/
Download Datasheet Parametric View All

54112-412-44-2400 Overview

Board Connector, 44 Contact(s), 2 Row(s), Male, Straight, 0.1 inch Pitch, Solder Terminal, Locking, Black Insulator, Receptacle

54112-412-44-2400 Parametric

Parameter NameAttribute value
Is it Rohs certified?incompatible
Objectid305904775
Reach Compliance Codecompliant
ECCN codeEAR99
body width0.19 inch
subject depth0.945 inch
body length2.2 inch
Body/casing typeRECEPTACLE
Connector typeBOARD CONNECTOR
Contact to complete cooperationSN-PB ON NI
Contact completed and terminatedTin/Lead (Sn/Pb) - with Nickel (Ni) barrier
Contact point genderMALE
Contact materialPHOSPHOR BRONZE
contact modeRECTANGULAR
Contact styleSQ PIN-SKT
Insulation resistance5000000000 Ω
Insulator colorBLACK
insulator materialTHERMOPLASTIC
JESD-609 codee0
Manufacturer's serial number54112
Plug contact pitch0.1 inch
Match contact row spacing0.1 inch
Installation option 1LOCKING
Installation methodSTRAIGHT
Installation typeBOARD
Number of connectorsONE
PCB row number2
Number of rows loaded2
Maximum operating temperature125 °C
Minimum operating temperature-65 °C
PCB contact patternRECTANGULAR
PCB contact row spacing2.54 mm
Plating thickness79u inch
Rated current (signal)3 A
GuidelineUL, CSA
reliabilityCOMMERCIAL
Terminal length0.095 inch
Terminal pitch2.54 mm
Termination typeSOLDER
Total number of contacts44
PDM: Rev:G
STATUS:
Released
Printed: Feb 20, 2009
.
Hardware engineer interview questions
Analog Circuit 1. What is the content of Kirchhoff's theorem? (Shilan Microelectronics) 2. The formula of the plate capacitor (C=εS/4πkd). (Unknown) 3. The most basic one is the curve characteristic o...
limeiyue MCU
The video signal carrying capacity close to 1MHz is not enough. What op amp can I use to design a voltage follower?
As the title says, the video signal current output by the linear array CMOS is too small, and the input resistance of the AD module used is only 50ohm. I want to use an op amp to design a voltage foll...
XuYong虚庸 Analog electronics
How does STM32 make AD continuously sample and then delay 500MS before DA continuously outputs
This is my current graduation project: using the AD and DA built into the STM32F103ZET6 chip, the waveform is first continuously collected by the AD and stored in the external SRAM. After 500MS, the C...
wjg2954 stm32/stm8
Research on voice acquisition system and external communication interface based on DSP.pdf
Research on voice acquisition system and external communication interface based on DSP.pdf...
yunhuihe DSP and ARM Processors
Why are the upper and lower rows of pins not parallel when laying out AD devices?
When drawing a minimum system board for STM32, why do the four 2.54*10 pin headers on the top and bottom seem to be bent, wider on the left and narrower on the right?...
littleshrimp Talking
Why does it say here that RBPU needs to be defined?
//----------------------------------------------------------------- // Name: RB port level change interrupt controls the switch of two-digit digital tubes, addition and subtraction display//----------...
嘻嘻嘻嘻啊啊 Microchip MCU

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1436  552  2331  2023  2298  29  12  47  41  20 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号