ZLTMM-117-06-F-D datasheet, PDF

ZLTMM-117-06-F-D: DescriptionBoard Connector, 34 Contact(s), 2 Row(s), Male, Straight, 0.079 inch Pitch, Solder Terminal, Black Insulator, Receptacle; CategoryThe connector The connector; File Size376KB，1 Pages; ManufacturerSAMTEC; Websitehttp://www.samtec.com/; Environmental Compliance

Download Datasheet Parametric View All

ZLTMM-117-06-F-D Overview

Board Connector, 34 Contact(s), 2 Row(s), Male, Straight, 0.079 inch Pitch, Solder Terminal, Black Insulator, Receptacle

Parameter Name	Attribute value
Is it Rohs certified?	conform to
Objectid	1155556236
Reach Compliance Code	compliant
ECCN code	EAR99
Other features	HIGH TEMPERATURE
body width	0.237 inch
subject depth	0.25 inch
body length	1.586 inch
Body/casing type	RECEPTACLE
Connector type	BOARD CONNECTOR
Contact to complete cooperation	AU ON NI
Contact point gender	MALE
Contact material	PHOSPHOR BRONZE
contact mode	RECTANGULAR
Contact style	SQ PIN-SKT
Dielectric withstand voltage	600VAC V
Insulation resistance	5000000000 Ω
Insulator color	BLACK
insulator material	LIQUID CRYSTAL POLYMER (LCP)
Manufacturer's serial number	ZLTMM
Plug contact pitch	0.079 inch
Match contact row spacing	0.079 inch
Installation method	STRAIGHT
Installation type	BOARD
Number of connectors	ONE
PCB row number	2
Number of rows loaded	2
Maximum operating temperature	105 °C
Minimum operating temperature	-65 °C
PCB contact pattern	RECTANGULAR
PCB contact row spacing	2.0066 mm
Plating thickness	FLASH inch
polarization key	CENTER
reliability	COMMERCIAL
Terminal length	0.09 inch
Terminal pitch	2.0066 mm
Termination type	SOLDER
Total number of contacts	34

How to set the interrupt nesting of Renesas RL78/G13 MCU: If I put the interrupt for reading IIC in the timer interrupt, the program will die. If I put it outside, it can run normally. The interrupt time is set to 4ms. Reading 6050 data in the timer interrup...; hy战斗吧 Electronics Design Contest

wince infrared and serial port: I need to add infrared support recently. I use 2440 and connect an infrared receiver to the board. I want to add infrared. Are the drivers used for infrared and serial ports the same? Or do I need to ...; zzqqking Embedded System

Please advise on the procedure of 2812 external EEPROM: In the given example/********************************************************************Function name: unsigned int EEPROM_Read_Status(void)Purpose: EEPROM read statusInput: NoneOutput: None*********...; mhlllf Microcontroller MCU

Why do the impedances of the two input terminals of the op amp need to be matched?: Taking a simple reverse proportional circuit built with an op amp as an example, what is the use of the resistor added to the non-inverting end?...; PCB板 Analog electronics

I have a conceptual question, signal pin?: I just started to get involved in hardware. I was reading a book about PowerLogic and found that it mentioned a kind of pin as Signal Pin. It said that this pin should be used for power/ground. Howeve...; zhanghuiyang Embedded System

I would like to ask ST sales support whether the STM32F10X motor library can support brushless DC motors.: As the title says: Can the STM32F10X motor library support brushless DC motors?The STM32F10X motor library supports PMSM under FOC. Since there are differences in the understanding of the distinction ...; jhxajh stm32/stm8

Shortcut: A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 AA AB AC AD AE AF AG AH AI AJ AK AL AM AN AO AP AQ AR AS AT AU AV AW AX AY AZ B0 B1 B2 B3 B4 B5 B6 B7 B8 B9 BA BB BC BD BE BF BG BH BI BJ BK BL BM BN BO BP BQ BR BS BT BU BV BW BX BY BZ C0 C1 C2 C3 C4 C5 C6 C7 C8 C9 CA CB CC CD CE CF CG CH CI CJ CK CL CM CN CO CP CQ CR CS CT CU CV CW CX CY CZ D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 DA DB DC DD DE DF DG DH DI DJ DK DL DM DN DO DP DQ DR DS DT DU DV DW DX DZ

Popular Components