Short tube inner packaging dimensions: L*W*H=255*170*80mm;
Short tube outer packaging dimensions(with six inner packaging boxes):
L*W*H=375*280*270mm;
Long tube inner packaging dimensions: L*W*H=580*200*100mm;
Long tube outer packaging dimensions(with two inner packaging boxes)
：
L*W*H=600*215*220mm;
Long tube outer packaging dimensions(with three inner packaging boxes)
：
L*W*H=600*215*325mm.
DESIGN & APPLY CONSIDERATIONS
1) Typical Application Circuits
(Analogue Dim)
(Analogue D im )
21
+Vin
GND
+Vin
22,23
21
14,16
+LED
KC24H-xxxX3
22,23
KC24H-xxxX3
14,16
+LED
9,11
4
Last LED
-LED
1st LED
GND
2,3
9,11
4
-LED
1st LED
Last LED
2xNPN
2,3
(PWM Di m/ON/OFF)
0.5~1Ω
(PWM D im/ ON /OFF)
(Figure 3)
Note:
Series Application
(Figure 4) Parallel-series Application
1. If input>40V, the input port must add an external capacitor (
≥
47μF/100V),to protect the module from damaged by voltage spikes.
2.
“-LED”
can’t connect GND, or the module may be damaged.
3. The module is a step-down driver, please refer to
“Input
VS Output” at page 3.
4. When the mode works in the high-voltage input-area and 1LED load, it is normal about Frequency hopping because of small duty cycle. Output current
is constant. Not affect the normal use.
2
) Digital Dimming Control
PWM Digital Control Signal
1
0
Output Current
1
0
The copyright and authority for the interpretation of the products are reserved by MORNSUN
PWM Digital Control Signal
1
0
Output Current(LED appears bright)
1
0
1
0
PWM Digital Control Signal
Output Current(LED appears dim)
KC24H
A/1-2012
Page 4 of 5
For the rated frequency PWM dimming, the output current of driver matters to the pulse width of the PWM signal.
and the numerate please refer to
the following formula:
I
o_set
=
(DT-0.75)
Io_set refers to the expected output current value (mA) , Io_norm refers to the rated output current (mA) , D refers to the pulse width of the PWM
signal (%),T refers to the cycle of the PWM signal (ms).
Note: The formula only supplies as a reference, and the output current may be a little deviation with different load. The Ton(min) of PWM signal
must be greater than 0.75ms, or the driver can’t operate normally. It is natural for the driver to generate an audibly noise in dimming process, because
the frequency of the control circuit is within human audibly range (20Hz~20KHz). In order to avoid the human eye can observe the LED flashes, the
PWM dimming frequency is recommended to set above 100Hz.
PWM curve(Vin=24V,5LEDs):
PWM Frequency VS Output
current(D=50%)
600
500
400
300
200
100
0
T
I
o_norm
KC24H-1000X3
KC24H-1200X3
Output current VS Pulse width of the
KC24H-1000X3
PWM signal (f=200Hz)
KC24H-1200X3
1000
900
800
700
600
500
400
300
200
100
0
20
30
40
50
60
70
80
Pulse width of the PWM signal
90
80
100
125
150
175
PWM Frequency
200
250
(Figure 5) PWM Frequency VS Output current(D=50%)
3) Analogue Dimming Control And Application Example
(Figure 6) Output current VS Pulse width of the PWM signal (f=200Hz)
Output current
Output current
100%
+Vin
GND
0-10V
On/Off
(Optional)
5K6
22,23
2,3
5K1
14,16 +LED
KC24H-xxxX3
9,11
21
4
-LED
1st LED
Last LED
0%
Output Current
Analogue Input Voltage
0.2V
1V
2V
3V
4V
5V
15V
Voltage Control(0-15V max)
(Figure 7) Analogue dimming circuit
4) No parallel connection(output) or plug and play
Note:
(Figure 8) Output current VS analogue input voltage
1. Operation under minimum load will not damage the converter; However, they may not meet all specification listed.
2. All specifications measured at Ta=25°C, humidity<75%, nominal input voltage and rated output load unless otherwise specified.
3. In this datasheet, all the test methods of indications are based on corporate standards.
4. Only typical models listed, other models may be different, please contact our technical person for more details.
5. Our company offer custom products.
6. Specifications subject to change without notice.
MORNSUN Science & Technology Co.,Ltd.
Address: No. 5, Kehui St. 1, Kehui development center, Science Ave., Guangzhou Science City, Luogang district, Guangzhou,P.R.China.
Tel: 86-20-38601850
Fax:86-20-38601272
Http://www.mornsun-power.com
The copyright and authority for the interpretation of the products are reserved by MORNSUN
Convert the following code to embedded vc++ 4.0 environment code. I don't know c++, please help me! #using#usingusing namespace System;using namespace System::Collections::Generic;void main(){//??????...
In any switching power supply design, the physical design of the PCB board is the last link. If the design method is not appropriate, the PCB may radiate too much electromagnetic interference, causing...
[i=s]This post was last edited by wsmysyn on 2017-11-13 16:05[/i] RT Is anyone using AD17? :) I haven't used a drawing board for a long time. When I was drawing today, I found that AD17 has changed a ...
This system originally used the Microchip platform, and now it is necessary to convert the platform to STM. Due to time constraints, I am seeking help from God. I would like anyone who specializes in ...
I'm a newbie, I want to use the timer in CC2530 to design a PWM wave with adjustable duty cycle. I've been working on it for a long time but the board doesn't respond. Does anyone have a program... I'...
DSP TMS320VC5509A is configured as the master device according to the official example of TI. DSP provides IIS clock signal and frame synchronization signal. The problem now is that it cannot generate...
1. Overview
Will passive devices
produce nonlinear intermodulation distortion? The answer is yes! Although there is no systematic theoretical analysis, it has been found in engineerin...[Details]
Due to the significant increase in electronic devices in automotive and industrial applications, the automotive and industrial markets continue to play an important role in China's electronics in...[Details]
System design is a complex process. It is not enough to just use ICs. There are many details to consider. This article uses a high-fidelity music playback system as an example to introduce how to s...[Details]
In this article, the high-performance DSP developed by TI can be used as an effective confidentiality method if it is applied to PC encryption cards.
As an effective network security solution,...[Details]
Abstract: In order to generate a stable excitation signal, the design of a digital frequency synthesizer is implemented on FPGA using Verilog hardware language. The design includes accumulator, wav...[Details]
Contact resistance
is the resistance to current flow through a closed pair of contacts. This type of measurement is performed on devices such as connectors,
relays
, and switches. The...[Details]
A standard cell
is an electrochemical
cell
used as a voltage reference standard in many electrical standards laboratories
. If properly maintained, standard cells are very stable. The ...[Details]
1 Introduction to HART Protocol
HART (Highway Addressable Remote Transducer), an open communication protocol for addressable remote sensor high-speed channels, was launched by Rosemen in the U...[Details]
This controller uses PIC16C54 single-chip microcomputer as the controller, and it is very easy to use: just connect a telephone line to the loudspeaker through the controller, and you can rem...[Details]
The concept of state machine
State machine is an important concept in software programming. More important than this concept is its flexible application. In a clear and efficient program, ther...[Details]
Printed circuit boards ( PCBs
)
are used in most electrical products
. If a PCB has low
insulation resistance
(IR), the performance of the circuits on the PCB will be greatly reduced...[Details]
Introduction
Nowadays, people pay more and more attention to the security alarm system, and people have higher and higher requirements for the functions and performance of the alarm. This paper prop...[Details]
With the rapid development of cities and the improvement of citizens' living standards, the number of various vehicles in cities is growing, and the demand for parking spaces in major commercial an...[Details]
In the "digital pressure measurement" experimental device of applied physics, the subject technical knowledge of analog circuits, digital circuits, sensors and single-chip microcomputers is used. In o...[Details]
Fruit planting is an important part of China's agricultural development, and fruit tree pest control operations are becoming more and more important. At present, the overall level of pesticide applica...[Details]
Embedded System
京公网安备 11010802033920号
EEWORLD
