EEWORLDEEWORLDEEWORLD

Part Number

Search

BSTCR-106-D-XXX-24-G-200-LT

Description
Board Connector, 12 Contact(s), 2 Row(s), Male, Right Angle, 0.1 inch Pitch, Solder Kinked Leads Terminal, Black Insulator, Receptacle
CategoryThe connector    The connector   
File Size170KB,1 Pages
ManufacturerMajor League Electronics
Websitehttp://www.mlelectronics.com/
Download Datasheet Parametric View All

BSTCR-106-D-XXX-24-G-200-LT Overview

Board Connector, 12 Contact(s), 2 Row(s), Male, Right Angle, 0.1 inch Pitch, Solder Kinked Leads Terminal, Black Insulator, Receptacle

BSTCR-106-D-XXX-24-G-200-LT Parametric

Parameter NameAttribute value
Is it Rohs certified?incompatible
Objectid1163303179
Reach Compliance Codecompliant
ECCN codeEAR99
Other featuresLEAD LENGTH=0.930 INCH
body length0.6 inch
Body/casing typeRECEPTACLE
Connector typeBOARD CONNECTOR
Contact to complete cooperationGOLD (10) OVER NICKEL (50)
Contact completed and terminatedGold Flash (Au) - with Nickel (Ni) barrier
Contact point genderMALE
Contact materialPHOSPHOR BRONZE
contact modeRECTANGULAR
Contact styleSQ PIN-SKT
Insulation resistance5000000000 Ω
Insulator colorBLACK
insulator materialGLASS FILLED POLYESTER
Manufacturer's serial numberBSTCR
Plug contact pitch0.1 inch
Match contact row spacing0.1 inch
Installation methodRIGHT ANGLE
Installation typeBOARD
Number of connectorsONE
PCB row number2
Number of rows loaded2
Maximum operating temperature125 °C
Minimum operating temperature-65 °C
PCB contact patternRECTANGULAR
PCB contact row spacing2.54 mm
Plating thickness10u inch
Rated current (signal)3 A
GuidelineUL
reliabilityCOMMERCIAL
Terminal pitch2.54 mm
Termination typeSOLDER KINKED LEADS
Total number of contacts12
The problem of Wince4.2 system being damaged
I installed Wince4.2 operating system on s3c2410 platform, and found that some boards were fine at the beginning, but then they could not start for unknown reasons. I checked with dnw, and it turned o...
helloween Embedded System
STM32F103C8T6 MCU TIM1 timer does not output PWM
The configuration process of the STM32F103C8T6 microcontroller advanced timer TIM1 is as shown in the figure below: Channel 1 PA8 is used. TIM1 is called in the same way as TIM2, but TIM2 can output P...
燕园技术宅 stm32/stm8
I would like to ask about the application of MQ series gas sensors such as MQ-4, MQ-7, MQ-137, etc.
How does the MQ series sensor convert the voltage value into the corresponding gas concentration value? What is the formula and how to derive it? Please give me some advice....
liushikai MCU
About MSP430 programming method selection
For MSP430, some chips have library functions. Do you prefer to continue to use registers for development or use new libraries for development, or use both? If you have any ideas or insights, please c...
fish001 Microcontroller MCU
How to implement nand flash access LOGO (in EBOOT)?
I am making a boot LOGO recently. There is a VGA module on the board connected to the monitor (1024X768). The logo is too big and the size of EBOOT cannot be controlled well with the previous mode. No...
weicunshang Embedded System
Graduated, sold the development board, and bought a laptop
I've graduated and want to buy a laptop. I'm selling my development board to buy a laptop. I have the following on hand: A Black Gold development board (90% new), a Zedboard (9.99% new), with a textbo...
rowen Buy&Sell

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1599  1080  2808  1327  24  33  22  57  27  1 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号