EEWORLDEEWORLDEEWORLD

Part Number

Search

54111-418-13-0850LF

Description
Board Connector, 13 Contact(s), 1 Row(s), Male, Straight, 0.1 inch Pitch, Solder Terminal, Locking, Black Insulator, Receptacle
CategoryThe connector    The connector   
File Size63KB,1 Pages
ManufacturerAmphenol
Websitehttp://www.amphenol.com/
Environmental Compliance
Download Datasheet Parametric View All

54111-418-13-0850LF Overview

Board Connector, 13 Contact(s), 1 Row(s), Male, Straight, 0.1 inch Pitch, Solder Terminal, Locking, Black Insulator, Receptacle

54111-418-13-0850LF Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
Objectid305813883
Reach Compliance Codecompliant
ECCN codeEAR99
body width0.094 inch
subject depth0.335 inch
body length1.3 inch
Body/casing typeRECEPTACLE
Connector typeBOARD CONNECTOR
Contact to complete cooperationSN ON NI
Contact completed and terminatedMatte Tin (Sn) - with Nickel (Ni) barrier
Contact point genderMALE
Contact materialPHOSPHOR BRONZE
contact modeRECTANGULAR
Contact styleSQ PIN-SKT
Insulation resistance5000000000 Ω
Insulator colorBLACK
insulator materialTHERMOPLASTIC
JESD-609 codee3
Manufacturer's serial number54111
Plug contact pitch0.1 inch
Installation option 1LOCKING
Installation methodSTRAIGHT
Installation typeBOARD
Number of connectorsONE
PCB row number1
Number of rows loaded1
Maximum operating temperature125 °C
Minimum operating temperature-65 °C
PCB contact patternRECTANGULAR
Plating thickness30u inch
Rated current (signal)3 A
GuidelineUL, CSA
reliabilityCOMMERCIAL
Terminal length0.095 inch
Terminal pitch2.54 mm
Termination typeSOLDER
Total number of contacts13
PDM: Rev:E
STATUS:
Released
Printed: Jun 03, 2008
.
EE_FPGA V1.0 Driver
Plug the EE_FPGA V1.0 USB into the computer, and it will prompt you to install the driver. I used C:\altera\91\quartus\drivers Can't install it properly. Can you help me and send me one? The JTAG down...
happy_xu00 FPGA/CPLD
Recommend a book
I just started learning microcontrollers, and I always feel that it is a bit difficult to understand just by reading the manual. Not long ago, I switched to learning avr. I borrowed a lot of books. I ...
jinchen Microchip MCU
About the problem of external power removal of TI LM3S8962 development board
Can I add an external 5V voltage between the 5V and GND of the double-row true lead to power the development board? Or can I only use USB to draw power? I didn't understand the schematic diagram! Urge...
wanghongyang Microcontroller MCU
Perform simple calculations on any parameter such as AD acquisition value, light, temperature, etc. in the experimental board, such as averaging, and then...
[align=left][font=宋体]Perform simple calculations on any parameter such as the AD acquisition value, light, temperature, etc. in the experimental board, such as averaging, and send it to the PC through...
郝文烁55 51mcu
Buoyancy automatic measurement system based on single chip microcomputer
Design a control system based on MCS-51 single chip microcomputer to realize automatic control of the device. The control system needs to control the stepper motor and realize the measurement and disp...
54534563 MCU
Urgent!!! Help!!!!
Dear experts, I used a 430F449 chip to make a small system. Its RST pin was only connected to the RST pin of JTAG, and there was no reset circuit. In this way, my JTAG debugging was fine, and after th...
szhgx26 Microcontroller MCU

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1102  774  1384  991  1485  23  16  28  20  30 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号