EEWORLDEEWORLDEEWORLD

Part Number

Search

WBA-T0303GG-02-4220-CD

Description
RES NET,THIN FILM,422 OHMS,100WV,.25% +/-TOL,-50,50PPM TC,0303 CASE
CategoryPassive components    The resistor   
File Size484KB,3 Pages
ManufacturerTT Electronics plc
Websitehttp://www.ttelectronics.com/
Download Datasheet Parametric View All

WBA-T0303GG-02-4220-CD Overview

RES NET,THIN FILM,422 OHMS,100WV,.25% +/-TOL,-50,50PPM TC,0303 CASE

WBA-T0303GG-02-4220-CD Parametric

Parameter NameAttribute value
Objectid1178355159
Reach Compliance Codecompliant
ECCN codeEAR99
structureChip
Manufacturer's serial numberWBA
Network TypeCenter Tap
Number of terminals6
Maximum operating temperature150 °C
Minimum operating temperature-55 °C
Package length0.762 mm
Package formSMT
Package width0.762 mm
method of packingTray
Rated power dissipation(P)0.25 W
resistance422 Ω
Resistor typeARRAY/NETWORK RESISTOR
seriesWBA
size code0303
Temperature Coefficient-50,50 ppm/°C
Tolerance0.25%
Operating Voltage100 V
Wire Bondable
Ceramic Resistors
WBA Series
High resistor density
Lower stray capacitance
Proven TaNFilm
®
on ceramic technology
IRC’s WBA series wire bondable ceramic resistors are ideally suited for
your most demanding hybrid application. IRC’s TaNFilm
®
tantalum nitride
thin film technology has years of proven stability, reliability and moisture performance.
IRC’s WBA series of ceramic chip resistors offer a wide range of tolerances and temperature coefficients to fit
a variety of hybrid circuit applications. Custom resistance values, sizes and schematics are also available on
request to the factory.
For high performance wire bondable ceramic resistors for hybrid circuit application, specify IRC WBA series
resistors.
Electrical Data
Absolute Tolerance
Ratio Tolerance
Absolute TCR
Tracking TCR
Package Power Rating (@ 70°C)
Rated Operating Voltage
(not to exceed
P x R )
Operating Temperature
Noise
Substrate Material
Substrate Thickness
Bond Pad Metallization
Backside
to ±0.1%
to ±0.05%
to ±25ppm/°C
to ±2ppm/°C
250mW
100V
-55°C to +150°C
<-30dB
99.6% Alumina
0.015˝ ±0.002
(0.381mm ±0.05)
Gold: 30KÅ minimum
Ceramic (gold available)
Physical Data
T0303 - Tapped network
(0.762mm ±0.025)
0.004˝ min
Bond Pads
A subsidiary of
TT electronics plc
0.030˝ ±0.001
(0.762mm ±0.025)
½R
½R
General Note
IRC reserves the right to make changes in product specification without notice or liability.
All information is subject to IRC’s own data and is considered accurate at time of going to print.
© IRC Advanced Film Division
• 4222 South Staples Street • Corpus Christi Texas 78411 USA
Telephone: 361 992 7900 • Facsimile: 361 992 3377 • Website: www.irctt.com
WBA Series Issue January 2009 Sheet 1 of 3
0.030˝ ±0.001
What kind of LCD screen do you all use?
Now I want to do a project of human-machine interface LCD 3.5-15 inches, touch screen The system supports graphical interface configuration functions, with curve drawing, list display and other functi...
songhaifei Microcontroller MCU
Two common MOSFET drive circuits 2
[b]Drive circuit composed of half-bridge driver chip[/b]The drive circuit composed of half-bridge driver chip is shown in Figure 4, and the working principle is as follows: A. When HS and LS are both ...
樱雅月 Automotive Electronics
wince5.0 about WIFI call
I want to call some control interfaces of wifi in my own application. But I found that the WZCQueryInterface function and WZCQueryInterfaceEx function, DWORD WZCQueryInterface( LPWSTR pSrvAddr, DWORD ...
chao2641 Embedded System
[Recommended information] Easy Power Nano Module Product Introduction Manual!
The new SIMPLE SWITCHER Nano Module combines ease of use and high performance in a tiny solution size. The Nano Module is the smallest 1A package on the market. The device is the first integrated indu...
soso Analogue and Mixed Signal
Datesheet of the million-door cyclone
Help on altera chip selection. Altera chip selection is mainly used for communication. Requirements: 1. More than 1 million gates 2. Embedded processor 3. Relatively new model. Thank you very much!!! ...
gxshill Embedded System
The LM3S9B96 core board can be connected normally using JTAG, but the Flash cannot be erased
I have soldered a new LM3S9B96 core board, but it always fails when I use JTAG SW mode to download the program. I tested it with SEGGER J-Flash ARM V4.12 and found that it can be successfully connecte...
无物之象 Microcontroller MCU

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1771  2450  215  1889  523  36  50  5  39  11 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号