EEWORLDEEWORLDEEWORLD

Part Number

Search

B0202GA-03-2910-C

Description
Fixed Resistor, Thin Film, 0.25W, 291ohm, 100V, 0.25% +/-Tol, 25ppm/Cel, Surface Mount, 0202, CHIP
CategoryPassive components    The resistor   
File Size381KB,3 Pages
ManufacturerTT Electronics plc
Websitehttp://www.ttelectronics.com/
Download Datasheet Parametric View All

B0202GA-03-2910-C Overview

Fixed Resistor, Thin Film, 0.25W, 291ohm, 100V, 0.25% +/-Tol, 25ppm/Cel, Surface Mount, 0202, CHIP

B0202GA-03-2910-C Parametric

Parameter NameAttribute value
Objectid1579390067
package instruction, 0202
Reach Compliance Codecompliant
ECCN codeEAR99
Installation featuresSURFACE MOUNT
Number of terminals2
Maximum operating temperature150 °C
Minimum operating temperature-55 °C
Package shapeRECTANGULAR PACKAGE
method of packingTRAY
Rated power dissipation(P)0.25 W
Rated temperature70 °C
resistance291 Ω
Resistor typeFIXED RESISTOR
size code0202
surface mountYES
technologyTHIN FILM
Temperature Coefficient25 ppm/°C
Terminal shapeONE SURFACE
Tolerance0.25%
Operating Voltage100 V
Wire Bondable
Chip Resistors
WBC Series
Discrete or tapped schematics
MIL inspection available
High resistor density
IRC’s WBC series wire bondable chip resistors are ideally suited for
the most demanding hybrid application. The WBC combines IRC’s
TaNSil
®
tantalum nitride thin film technology with silicon substrate processing to produce an extremely small
footprint device with the proven stability, reliability and moisture performance of IRC’s TaNSil
®
resistor film.
Available in a wide range of tolerances and temperature coefficients to fit a variety of hybrid circuit applica-
tions. Custom resistance values, sizes and schematics are available on request from the factory.
Physical Data
R0202 - Discrete
(0.508mm ±0.025)
0.020˝ ±0.001
Electrical Data
Absolute Tolerance
Absolute TCR
Package Power Rating
(@ 70°C)
Rated Operating Voltage
(not to exceed P x R )
Operating Temperature
Back contact
Noise
R
Top contact
pad chamfered
0.004˝ min bond pad size
to ±0.1%
to ±25ppm/°C
250mW
100V
-55°C to +150°C
<-30dB
Oxidized Silicon
(10KÅ SiO
2
min)
0.010˝ ±0.001
(0.254mm ±0.025)
10KÅ minimum
15KÅ minimum
Silicon
(Al / Au optional)
3KÅ Au minimum
10KÅ Al minimum
Silicon Dioxide or
Silicon Nitride
R
0.004˝ min bond pad size
0.020˝ ±0.001
(0.508mm ±0.025)
B0202 - Discrete back contact
(0.508mm ±0.025)
0.020˝ ±0.001
Substrate Material
Top contact
Substrate Thickness
Aluminum
Gold
R0202 and
T0303
B0202
0.020˝ ±0.001
(0.508mm ±0.025)
T0303 - Tapped network ½R + ½R
Bond Pad
Metallization
(0.762mm ±0.025)
0.030˝ ±0.001
½R
½R
Backside
0.030˝ ±0.001
(0.762mm ±0.025)
0.004˝ min bond pad size
Passivation
General Note
IRC reserves the right to make changes in product specification without notice or liability.
All information is subject to IRC’s own data and is considered accurate at time of going to print.
© IRC Advanced Film Division
• Corpus Christi Texas 78411 USA
Telephone: 361 992 7900 • Facsimile: 361 992 3377 • Website: www.irctt.com
A subsidiary of
TT electronics plc
WBC Series Issue January 2009 Sheet 1 of 3
PC serial port directly sends AT commands to GSM module
I directly connected the serial port and the module, and then used the serial port debugging assistant to send commands. There was no return value when sending "AT", but the indicator light on the mod...
游在云间 51mcu
89C2051
When using Keil c to program AT89C2051, its data storage shows /P> data=10.3, xdata=0, code=473. 2051 has only 2K storage and 128 bytes of internal RAM. However, the compiled data is basically stored ...
kgdwfnyga 51mcu
Anyone who has worked on SD card drivers please come in and tell me what is the difference between MMC's stream data transfer and block data transfer?
I am reading the development document of s3c2410, and there is a sentence about sd card controller: sd card data transfer mode has stream data transfer and block data transfer, what is the difference ...
000000000000 Embedded System
How much do you know about RF semiconductor technology in the wireless era?
Semiconductor materials are electronic materials that have semiconductor properties (conductivity between conductors and insulators, resistivity in the range of about 1mΩ·cm to 1GΩ·cm) and can be used...
btty038 Energy Infrastructure?
IC packaging
IC packaging form...
cnxex Analog electronics
How to design the vias on the heat sink? The problem is not solved, please help me
[i=s] This post was last edited by yjguohua on 2019-4-25 11:14 [/i] [color=#008000][backcolor=rgb(255, 255, 255)][font=Tahoma,]I would like to ask, how should I drill the heat dissipation holes on the...
yjguohua PCB Design

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2553  1480  108  2699  2536  52  30  3  55  14 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号