Contact Resistance Variation ...........................±1 % .................................................................±3 % of total resistance or 3 ohms
(whichever is greater)
Dielectric Withstanding Voltage (MIL-STD-202, Method 301)
Total Resistance Shift ................................... ±10 % maximum ................................................ ±3 % maximum
Rotational Life (No Load) ................................... 100,000 cycles ................................................... 20,000 cycles
Total Resistance Shift ................................... ±15 % TRS maximum ....................................... ±5 % or 5 ohms TRS whichever is greater
Torque (Starting and Running)..................................................................................... A & B bushings 0.35 to 4.23 N-cm (0.05 to 6.0 oz.-in.)
C & E bushings 0.21 to 4.23 N-cm (0.3 to 6.0 oz.-in.)
3856 – 0.11 to 2.12 N-cm (0.15 to 3.0 oz.-in.)
Mounting (Torque on Bushing) ........................................................................................................... 1.7-2.0 N-m (15-18 lb.-in.) maximum
Weight (Single Section) ......................................................................................................................................................30 grams maximum
Terminals ................................................................................................................................................ Printed circuit terminals or solder lugs
Soldering Condition ............................................Recommended hand soldering using Sn95/Ag5 no clean solder, 0.025 ˝ wire diameter.
Maximum temperature 399 °C (750 °F) for 3 seconds. No wash process to be used with no clean flux.
Part can be wave soldered at 260 °C (500 °F) for 5 seconds, no wash process with no clean flux.
Marking...........................................................................Manufacturer’s trademark, wiring diagram, resistance, date code, and part number
Ganging (Multiple Section Potentiometers) ..............................................................................................................................1 cup maximum
Hardware.................................................................................... One lockwasher and one mounting nut is shipped with each potentiometer;
locking bushing versions are shipped with one additional locking nut
specifications tested at 250 RPM, at room ambient: +25 °C nominal.
Specifications are subject to change without notice.
Users should verify actual device performance in their specific applications.
The products described herein and this document are subject to specific legal disclaimers as set forth on the last page of this document, and at www.bourns.com/docs/legal/disclaimer.pdf.
3851/3852/3856 – 3/4 ˝ Diameter Panel Control
Product Dimensions
9.53
(.38)
.38
(.015)
12.7, 22.23
STD.
(1/2, 7/8)
3/8-32 UNEF
.25
45
°
X
(.010)
CHAMFER
6.35+.03/-.05
DIA.
(.250+.001/-.002)
SHAFT SLOT
1.19
.047 WIDE X
1.60+.38/.00
DEEP
(.063+.015/-.000)
6.35
±
.76
(.25
±
.03)
12.7
(.50)
.38
(.015)
15.88
STD.
(5/8)
3/8-32 UNEF
.25
45
°
X
(.010)
CHAMFER
6.35+.03/-.05
DIA.
(.250+.001/-.002)
SHAFT SLOT
1.19 WIDE X
(.047)
1.60+.38/-.00
(.063+.015/-.000)DEEP
6.35
±
.76
(.25
±
.03)
19.05
(.75)
DIA.
12.19
DIA.
(.480)
19.05
(.75)
DIA.
12.19
DIA.
(.48)
SOLDER LUG TERMINAL
6.35
2.79
(.25)
TYP.
(.110)
3 PLCS.
12.7
(.50)
EACH TERMINAL LUG
2
3
2 PLCS.
1
WILL ACCOMMODATE
.72
THREE
(.028)
DIAMETER
14.02
±
.25
(.724 DIA. AWG
(.552
±
.010)
STRANDED) WIRES.
STANDARD
PRINTED CIRCUIT TERMINAL
1.02
6.35
TYP.
TYP.
(.040)
(.25)
15.88
±
.38
(.625
±
.015)
16.00
5.49
OPTIONAL FLAT
(.63)
(.216)
1.52
28.58
LONG OR
FRONT BUSHING FOR SHAFTS UNDER
(.06)
(1-1/8)
1
2
3
6.35
(.25)
6.35
(.25)
9.53, 22.23
STD.
(3/8, 7/8)
.38
(.015)
2.36
(.094)
1/4-32 UNEF
.25
45
°
X (.010)
CHAMFER
6.35
±
.76
(.25
±
.03)
9.53
(.38)
.38
(.015)
12.7
STD.
(1/2)
1/4-32 UNEF
.25
45
°
X (.010)
CHAMFER
6.35
±
.76
(.25
±
.03)
SUGGESTED BOARD LAYOUT
6.35
6.35
(.25)
(.25)
1.40
DIA.
(.055)
19.05
(.75)
DIA.
12.19
DIA.
(.480)
19.05
(.75)
DIA.
3.18
±
0.25
DIA.
(.125
±
.001)
3.18
±
.025
DIA.
(.125
±
.001)
SHAFT SLOT
.79 WIDE X .76 DEEP
(.031)
(.03)
.25
OPTIONAL FLAT
LONG OR
(.010)
1.52
15.88
FRONT BUSHING FOR SHAFTS UNDER
(.06)
(5/8)
SHAFT SLOT
.79 WIDE X .76 DEEP
(.03)
(.031)
12.19
DIA.
(.480)
A, B & H BUSHINGS
9.53
(.375)
C & E BUSHINGS
9.53
(.375)
9.91
DIA.
(.390)
3.18
DIA.
(.125)
3.18
6.73
DIA.
(.125)DIA.
(.265)
9.53
(.38)
6.35
±
.76
(.25
±
.03)
12.7
(.50)
.38
(.015)
6.35+.03/-.05
DIA.
(.250+.001/-.002)
3/8-32 UNEF
1.19
(.047)
9.53
(.38)
6.35
±
.76
(.25
±
.03)
.38
(.015)
12.7
(.50)
6.35+.03/-.05
DIA.
(.250
±
.03)
3/8-32 UNEF.
.79
(.031)
SHAFT SLOT
ALIGNMENT
AT CCW
FLAT
ALIGNMENT
AT CCW
50
° ±
10
°
50
° ±
10
°
19.05
(.75)
DIA.
12.19
DIA.
(.480)
1.60+3.81/-.000
(.063+.015/-.000)
DIA.
22.23
STD.
(7/8)
19.05
(.75)
DIA.
12.19
DIA.
(.480)
.79
±
.25
(.031
±
.010)
22.23
STD.
(7/8)
3.18
±
.03
(.125
±
.003)
DIA.
.25
45
°
X (.010)
CHAMFER
2.67
±
.381
(.105
±
.015)
ANTI-ROTATION LUG
PROJECTS 1/16 INCH
ABOVE MOUNTING FACE.
TOLERANCES EXCEPT AS NOTED:
.127
.XX
±
.38
DECIMALS: .XXX
±
(.005),
(.015)
FRACTIONS:
±
1/64
ANGLE:
±
3 %
.25
45
°
X (.010)
CHAMFER
DIMENSIONS:
MM
(INCHES)
CCW
1
3
Specifications are subject to change without notice.
Users should verify actual device performance in their specific applications.
The products described herein and this document are subject to specific legal disclaimers as set forth on the last page of this document, and at www.bourns.com/docs/legal/disclaimer.pdf.
POTENTIOMETER
2
3851/3852/3856 – 3/4 ˝ Diameter Panel Control
Hardware
LOCKWASHER H-37-1
6.6
(.26)
NUT H-38-1
9.53 +0/-0.38
(.375 +0/-.015)
2.36 ± 0.25
(.093 ± .01)
LOCKNUT H-38-3
4.57 ± 0.05
(.180 ± .002)
7.75
(.305)
11 +0/-0.43
(.433 +0/-.017)
NUT H-38-2
2.36 ± 0.25
(.093 ± .01)
30 ° ± 5 °
1.02
(.040)
30 ° ± 5 °
TYP.
0.64
(.025)
15 ° ± 1 °
1/4-32 UNEF
1/4-32
NEF-20
12.07 ± 0.25
(.475 ± .01)
LOCKWASHER H-37-2
9.58 ± 0.36
(.377 ± .014)
0.64 ± 0.05
(.025 ± .002)
7.92
(.312)
3/8-32 NEF-2B
3.96
(.156)
12.52 ± 0.36
(.493 ± .014)
0.56 ± 0.05
(.022 ± .002)
14.66 +0/-0.43
(.577 +0/-.017)
30 ° ± 5 °
Date Code Description
YYWWM
M = COUNTRY OF MANUFACTURE
(MEXICO)
WW = WEEK NUMBER
YY = LAST TWO DIGITS OF YEAR
MANUFACTURED
DIMENSIONS:
MM
(INCHES)
LOCKNUT H-38-4
8.51 ± 0.05
(.335 ± .002)
1.91
MIN.
(.075)
18 ° ± 2 °
3/8-32
NEF-2B
1.02
(.040)
12.7
(.5)
1.14 ± 0.38
(.045 ± .015)
30 ° ± 5 ° TYP.
4.83
(.19)
Specifications are subject to change without notice.
Users should verify actual device performance in their specific applications.
The products described herein and this document are subject to specific legal disclaimers as set forth on the last page of this document, and at www.bourns.com/docs/legal/disclaimer.pdf.
3851/3852/3856 – 3/4 ˝ Diameter Panel Control
How To Order
3852
A
-
28
2
-
103
A
L
12
16
16
20
28
28
SHAFT TYPE
(FMS) & DIAMETER
3/8 ” (9.53 mm) L X 1/8 ” (3.18 mm) D
1/2 ” (12.7 mm) L x 1/4 ” (6.35 mm) D
1/2 ” (12.7 mm) L x 1/8 ” (3.18 mm) D
5/8 ” (15.88 mm) L X 1/4 ” (6.35 mm) D
7/8 ” (22.20 mm) L X 1/4 ” (6.35 mm) D
7/8 ” (22.20 mm) L X 1/8 ” (3.18 mm) D
AVAILABLE ONLY IN
MODELS
3851, 3852
3851, 3852
3851, 3852
3851, 3852
3851, 3852
3856
3851, 3852
3856
BUSHINGS
C
A
C, E
A, B
A, B
A
C, E
H
Consult factory for lengths not shown.
A
B
C
E
H
BUSHING
Plain 3/8 ” (9.53 mm) D x 3/8 ” (9.53 mm) L
Locking 3/8 ” (9.53 mm) D x 1/2 ” (12.7 mm) L
Plain 1/4 ” (6.35 mm) D x 1/4 ” (6.35 mm) L
Locking 1/4 ” (6.35 mm) D x 1/2 ” (12.7 mm) L
Plain 3/8 ” (9.53 mm) D x 3/8 ” (9.53 mm) L
APPLICABLE MODELS
3851, 3852, 3856
3851, 3852
3851, 3852
3851, 3852
3856 (3.18 mm D Shaft)
RESISTANCE
CODE/VALUE
(IN OHMS)
Model 3851
(102)
1K
(252)
2.5 K
(502)
5K
(103)
10 K
(253)
25 K
(503)
50 K
(104)
100 K
(254)
250 K
(504)
500 K
(105)
1M
Models 3852/3856
(101)
100
(251)
250
(501)
500
(102)
1K
(252)
2.5 K
(502)
5K
(103)
10 K
(253)
25 K
(503)
50 K
(104)
100 K
(254)
250 K
(504)
500 K
(105)
1M
ELEMENT
TAPER/TOLERANCE
A
Linear ±10 %
B
Linear ±20 %
C
Audio CW ±10 %
D
Audio CW ±20 %
E
Linear ±10 %
F
Audio CCW ±10 %
G
Audio CCW ±20 %
H
Linear ±5 %
RoHS IDENTIFIER
L
Compliant
MODEL
3851 3/4 ” (19.05 mm) D Single-Turn C.P.
3852 3/4 ” (19.05 mm) D Single-Turn Cermet
3856 3/4 ” (19.05 mm) D 3-3/4-Turn Cermet
TERMINAL STYLE AND
SHAFT TYPE
1
2
3
5
6
7
Solder Lugs, Plain End
Solder Lugs, Slotted End
Solder Lugs, Flatted Shaft
PC Pins, Plain End
PC Pins, Slotted End
PC Pins, Flatted Shaft
Boldface features are Bourns standard options.
All others are available with higher minimum order
quantities.
APPLICABLE
MODELS
3852, 3856
3851
3852, 3856
3851
3851
3852, 3856
3851
3852, 3856
Asia-Pacific:
Tel: +886-2 2562-4117 • Email: asiacus@bourns.com
EMEA:
Tel: +36 88 885 877 • Email: eurocus@bourns.com
The Americas:
Tel: +1-951 781-5500 • Email: americus@bourns.com
www.bourns.com
REV. 10/20
Specifications are subject to change without notice.
Users should verify actual device performance in their specific applications.
The products described herein and this document are subject to specific legal disclaimers as set forth on the last page of this document, and at www.bourns.com/docs/legal/disclaimer.pdf.
As the title says, I want to use NMOS to make a fast switch, with the source pull-down resistor connected to ground and the drain connected to VDD=+48V. When turned on, the source voltage will be pull...
The following is a simple process for programming the Model 2602 SourceMeter instrument:1 ) Create a script;2 ) Download the script to the device;3 ) Call the script to run.Scripts for the Model 2602 ...
I use a current transformer to collect AC (industrial frequency) current, get AC voltage on the attenuator, perform AC-DC conversion and send it to the AD input of MSP430F435. The output code (4096) j...
Mr. Yan joined Tencent Interactive Entertainment in July 2012 as a senior engineer in the game platform department.
In March 2019, Tencent terminated the labor contract with Mr. Yan on the grounds tha...
Original question link: [url]https://bbs.eeworld.com.cn/forum.php?mod=viewthread&tid=478369&page=1#pid1953749[/url] Can the high-end drive circuit of the MOS tube be used as the controller of the elec...
On August 24th, Jin Yuzhi, CEO of Huawei's Intelligent Automotive Solutions BU, announced the first automotive application of Huawei Qiankun's unique Limera technology. This technology eliminates t...[Details]
The problem of dynamic sealing of equipment always exists with the operation of the equipment. Today, we have specially sorted out the various commonly used sealing forms, usage scope and character...[Details]
Most of the houses we live in now are elevator buildings, mainly because it is more convenient to go up and down the stairs! It can also make life more comfortable. It even helps to increase the ad...[Details]
In recent years, the government has increasingly supported electric vehicles, and the number of electric vehicles has increased. Observant drivers will notice that there are many more green license...[Details]
Limited vocabulary recognition
According to the number of characters, words or short sentences in the vocabulary, it can be roughly divided into: less than 100 is small vocabulary; 100-1000 is...[Details]
We are entering a new era where people are increasingly affordably equipped with more electronic gadgets. Electronics have become essential to our lives. For example, the average consumer now owns ...[Details]
In mobile technology, sensors are the primary input for measured signals and form a component of a sensor system. They include sensitive and transducer elements connected to carriers and circuits. ...[Details]
1. Introduction
Electronic scales are gradually replacing traditional measuring tools like springs and balances in everyday life, such as electronic price computing scales and electronic weigh...[Details]
According to foreign media reports, researchers at the University of Surrey have developed an artificial intelligence system that can accurately locate the location of equipment in densely populate...[Details]
On August 22, according to the Ministry of Industry and Information Technology's official website, my country's first mandatory national standard for the control of hazardous substances in electric...[Details]
Have you ever heard stories about "crazy appliances"? Think of microwaves that turn on automatically or ovens that preheat without any human input? With radios and electromagnetic interfaces ubiqui...[Details]
Tires are a very important component for cars. They are related to the driving experience of the vehicle. We are almost inseparable from cars in our daily lives. For tires, according to the role of...[Details]
With the increasing number of new energy vehicles on the road, the deployment of supporting facilities for these vehicles has accelerated, and new energy vehicles have gradually entered the vision ...[Details]
According to Nikkei, Japan has performed poorly in responding to China's power semiconductor challenges.
There are five major companies in Japan's power chip market: Mitsubishi Electric,...[Details]
Linear motor modules have become the "sweet spot" in various fields due to their advantages such as long stroke, fast speed, high precision, smooth operation and long life. Different models of line...[Details]
Embedded System
京公网安备 11010802033920号
EEWORLD
