Contact Resistance Variation ...........................±1 % .................................................................±3 % of total resistance or 3 ohms
(whichever is greater)
Dielectric Withstanding Voltage (MIL-STD-202, Method 301)
Total Resistance Shift ................................... ±10 % maximum ................................................ ±3 % maximum
Rotational Life (No Load) ................................... 100,000 cycles ................................................... 20,000 cycles
Total Resistance Shift ................................... ±15 % TRS maximum ....................................... ±5 % or 5 ohms TRS whichever is greater
Torque (Starting and Running)..................................................................................... A & B bushings 0.35 to 4.23 N-cm (0.05 to 6.0 oz.-in.)
C & E bushings 0.21 to 4.23 N-cm (0.3 to 6.0 oz.-in.)
3856 – 0.11 to 2.12 N-cm (0.15 to 3.0 oz.-in.)
Mounting (Torque on Bushing) ........................................................................................................... 1.7-2.0 N-m (15-18 lb.-in.) maximum
Weight (Single Section) ......................................................................................................................................................30 grams maximum
Terminals ................................................................................................................................................ Printed circuit terminals or solder lugs
Soldering Condition ............................................Recommended hand soldering using Sn95/Ag5 no clean solder, 0.025 ˝ wire diameter.
Maximum temperature 399 °C (750 °F) for 3 seconds. No wash process to be used with no clean flux.
Part can be wave soldered at 260 °C (500 °F) for 5 seconds, no wash process with no clean flux.
Marking...........................................................................Manufacturer’s trademark, wiring diagram, resistance, date code, and part number
Ganging (Multiple Section Potentiometers) ..............................................................................................................................1 cup maximum
Hardware.................................................................................... One lockwasher and one mounting nut is shipped with each potentiometer;
locking bushing versions are shipped with one additional locking nut
specifications tested at 250 RPM, at room ambient: +25 °C nominal.
Specifications are subject to change without notice.
Users should verify actual device performance in their specific applications.
The products described herein and this document are subject to specific legal disclaimers as set forth on the last page of this document, and at www.bourns.com/docs/legal/disclaimer.pdf.
3851/3852/3856 – 3/4 ˝ Diameter Panel Control
Product Dimensions
9.53
(.38)
.38
(.015)
12.7, 22.23
STD.
(1/2, 7/8)
3/8-32 UNEF
.25
45
°
X
(.010)
CHAMFER
6.35+.03/-.05
DIA.
(.250+.001/-.002)
SHAFT SLOT
1.19
.047 WIDE X
1.60+.38/.00
DEEP
(.063+.015/-.000)
6.35
±
.76
(.25
±
.03)
12.7
(.50)
.38
(.015)
15.88
STD.
(5/8)
3/8-32 UNEF
.25
45
°
X
(.010)
CHAMFER
6.35+.03/-.05
DIA.
(.250+.001/-.002)
SHAFT SLOT
1.19 WIDE X
(.047)
1.60+.38/-.00
(.063+.015/-.000)DEEP
6.35
±
.76
(.25
±
.03)
19.05
(.75)
DIA.
12.19
DIA.
(.480)
19.05
(.75)
DIA.
12.19
DIA.
(.48)
SOLDER LUG TERMINAL
6.35
2.79
(.25)
TYP.
(.110)
3 PLCS.
12.7
(.50)
EACH TERMINAL LUG
2
3
2 PLCS.
1
WILL ACCOMMODATE
.72
THREE
(.028)
DIAMETER
14.02
±
.25
(.724 DIA. AWG
(.552
±
.010)
STRANDED) WIRES.
STANDARD
PRINTED CIRCUIT TERMINAL
1.02
6.35
TYP.
TYP.
(.040)
(.25)
15.88
±
.38
(.625
±
.015)
16.00
5.49
OPTIONAL FLAT
(.63)
(.216)
1.52
28.58
LONG OR
FRONT BUSHING FOR SHAFTS UNDER
(.06)
(1-1/8)
1
2
3
6.35
(.25)
6.35
(.25)
9.53, 22.23
STD.
(3/8, 7/8)
.38
(.015)
2.36
(.094)
1/4-32 UNEF
.25
45
°
X (.010)
CHAMFER
6.35
±
.76
(.25
±
.03)
9.53
(.38)
.38
(.015)
12.7
STD.
(1/2)
1/4-32 UNEF
.25
45
°
X (.010)
CHAMFER
6.35
±
.76
(.25
±
.03)
SUGGESTED BOARD LAYOUT
6.35
6.35
(.25)
(.25)
1.40
DIA.
(.055)
19.05
(.75)
DIA.
12.19
DIA.
(.480)
19.05
(.75)
DIA.
3.18
±
0.25
DIA.
(.125
±
.001)
3.18
±
.025
DIA.
(.125
±
.001)
SHAFT SLOT
.79 WIDE X .76 DEEP
(.031)
(.03)
.25
OPTIONAL FLAT
LONG OR
(.010)
1.52
15.88
FRONT BUSHING FOR SHAFTS UNDER
(.06)
(5/8)
SHAFT SLOT
.79 WIDE X .76 DEEP
(.03)
(.031)
12.19
DIA.
(.480)
A, B & H BUSHINGS
9.53
(.375)
C & E BUSHINGS
9.53
(.375)
9.91
DIA.
(.390)
3.18
DIA.
(.125)
3.18
6.73
DIA.
(.125)DIA.
(.265)
9.53
(.38)
6.35
±
.76
(.25
±
.03)
12.7
(.50)
.38
(.015)
6.35+.03/-.05
DIA.
(.250+.001/-.002)
3/8-32 UNEF
1.19
(.047)
9.53
(.38)
6.35
±
.76
(.25
±
.03)
.38
(.015)
12.7
(.50)
6.35+.03/-.05
DIA.
(.250
±
.03)
3/8-32 UNEF.
.79
(.031)
SHAFT SLOT
ALIGNMENT
AT CCW
FLAT
ALIGNMENT
AT CCW
50
° ±
10
°
50
° ±
10
°
19.05
(.75)
DIA.
12.19
DIA.
(.480)
1.60+3.81/-.000
(.063+.015/-.000)
DIA.
22.23
STD.
(7/8)
19.05
(.75)
DIA.
12.19
DIA.
(.480)
.79
±
.25
(.031
±
.010)
22.23
STD.
(7/8)
3.18
±
.03
(.125
±
.003)
DIA.
.25
45
°
X (.010)
CHAMFER
2.67
±
.381
(.105
±
.015)
ANTI-ROTATION LUG
PROJECTS 1/16 INCH
ABOVE MOUNTING FACE.
TOLERANCES EXCEPT AS NOTED:
.127
.XX
±
.38
DECIMALS: .XXX
±
(.005),
(.015)
FRACTIONS:
±
1/64
ANGLE:
±
3 %
.25
45
°
X (.010)
CHAMFER
DIMENSIONS:
MM
(INCHES)
CCW
1
3
Specifications are subject to change without notice.
Users should verify actual device performance in their specific applications.
The products described herein and this document are subject to specific legal disclaimers as set forth on the last page of this document, and at www.bourns.com/docs/legal/disclaimer.pdf.
POTENTIOMETER
2
3851/3852/3856 – 3/4 ˝ Diameter Panel Control
Hardware
LOCKWASHER H-37-1
6.6
(.26)
NUT H-38-1
9.53 +0/-0.38
(.375 +0/-.015)
2.36 ± 0.25
(.093 ± .01)
LOCKNUT H-38-3
4.57 ± 0.05
(.180 ± .002)
7.75
(.305)
11 +0/-0.43
(.433 +0/-.017)
NUT H-38-2
2.36 ± 0.25
(.093 ± .01)
30 ° ± 5 °
1.02
(.040)
30 ° ± 5 °
TYP.
0.64
(.025)
15 ° ± 1 °
1/4-32 UNEF
1/4-32
NEF-20
12.07 ± 0.25
(.475 ± .01)
LOCKWASHER H-37-2
9.58 ± 0.36
(.377 ± .014)
0.64 ± 0.05
(.025 ± .002)
7.92
(.312)
3/8-32 NEF-2B
3.96
(.156)
12.52 ± 0.36
(.493 ± .014)
0.56 ± 0.05
(.022 ± .002)
14.66 +0/-0.43
(.577 +0/-.017)
30 ° ± 5 °
Date Code Description
YYWWM
M = COUNTRY OF MANUFACTURE
(MEXICO)
WW = WEEK NUMBER
YY = LAST TWO DIGITS OF YEAR
MANUFACTURED
DIMENSIONS:
MM
(INCHES)
LOCKNUT H-38-4
8.51 ± 0.05
(.335 ± .002)
1.91
MIN.
(.075)
18 ° ± 2 °
3/8-32
NEF-2B
1.02
(.040)
12.7
(.5)
1.14 ± 0.38
(.045 ± .015)
30 ° ± 5 ° TYP.
4.83
(.19)
Specifications are subject to change without notice.
Users should verify actual device performance in their specific applications.
The products described herein and this document are subject to specific legal disclaimers as set forth on the last page of this document, and at www.bourns.com/docs/legal/disclaimer.pdf.
3851/3852/3856 – 3/4 ˝ Diameter Panel Control
How To Order
3852
A
-
28
2
-
103
A
L
12
16
16
20
28
28
SHAFT TYPE
(FMS) & DIAMETER
3/8 ” (9.53 mm) L X 1/8 ” (3.18 mm) D
1/2 ” (12.7 mm) L x 1/4 ” (6.35 mm) D
1/2 ” (12.7 mm) L x 1/8 ” (3.18 mm) D
5/8 ” (15.88 mm) L X 1/4 ” (6.35 mm) D
7/8 ” (22.20 mm) L X 1/4 ” (6.35 mm) D
7/8 ” (22.20 mm) L X 1/8 ” (3.18 mm) D
AVAILABLE ONLY IN
MODELS
3851, 3852
3851, 3852
3851, 3852
3851, 3852
3851, 3852
3856
3851, 3852
3856
BUSHINGS
C
A
C, E
A, B
A, B
A
C, E
H
Consult factory for lengths not shown.
A
B
C
E
H
BUSHING
Plain 3/8 ” (9.53 mm) D x 3/8 ” (9.53 mm) L
Locking 3/8 ” (9.53 mm) D x 1/2 ” (12.7 mm) L
Plain 1/4 ” (6.35 mm) D x 1/4 ” (6.35 mm) L
Locking 1/4 ” (6.35 mm) D x 1/2 ” (12.7 mm) L
Plain 3/8 ” (9.53 mm) D x 3/8 ” (9.53 mm) L
APPLICABLE MODELS
3851, 3852, 3856
3851, 3852
3851, 3852
3851, 3852
3856 (3.18 mm D Shaft)
RESISTANCE
CODE/VALUE
(IN OHMS)
Model 3851
(102)
1K
(252)
2.5 K
(502)
5K
(103)
10 K
(253)
25 K
(503)
50 K
(104)
100 K
(254)
250 K
(504)
500 K
(105)
1M
Models 3852/3856
(101)
100
(251)
250
(501)
500
(102)
1K
(252)
2.5 K
(502)
5K
(103)
10 K
(253)
25 K
(503)
50 K
(104)
100 K
(254)
250 K
(504)
500 K
(105)
1M
ELEMENT
TAPER/TOLERANCE
A
Linear ±10 %
B
Linear ±20 %
C
Audio CW ±10 %
D
Audio CW ±20 %
E
Linear ±10 %
F
Audio CCW ±10 %
G
Audio CCW ±20 %
H
Linear ±5 %
RoHS IDENTIFIER
L
Compliant
MODEL
3851 3/4 ” (19.05 mm) D Single-Turn C.P.
3852 3/4 ” (19.05 mm) D Single-Turn Cermet
3856 3/4 ” (19.05 mm) D 3-3/4-Turn Cermet
TERMINAL STYLE AND
SHAFT TYPE
1
2
3
5
6
7
Solder Lugs, Plain End
Solder Lugs, Slotted End
Solder Lugs, Flatted Shaft
PC Pins, Plain End
PC Pins, Slotted End
PC Pins, Flatted Shaft
Boldface features are Bourns standard options.
All others are available with higher minimum order
quantities.
APPLICABLE
MODELS
3852, 3856
3851
3852, 3856
3851
3851
3852, 3856
3851
3852, 3856
Asia-Pacific:
Tel: +886-2 2562-4117 • Email: asiacus@bourns.com
EMEA:
Tel: +36 88 885 877 • Email: eurocus@bourns.com
The Americas:
Tel: +1-951 781-5500 • Email: americus@bourns.com
www.bourns.com
REV. 10/20
Specifications are subject to change without notice.
Users should verify actual device performance in their specific applications.
The products described herein and this document are subject to specific legal disclaimers as set forth on the last page of this document, and at www.bourns.com/docs/legal/disclaimer.pdf.
[i=s]This post was last edited by weizhongc on 2018-3-20 22:36[/i] I received a Raspberry Pi 3+ and thought it was pretty good. I also started to try out the Raspberry Pi. 1. First download the [url=h...
Thanks to [color=#000000]古道热肠MP3[/color] for providing this PCB, which is well designed. The express was delivered at 4:30 today, so I went home late after get off work. I finished the soldering in an...
Wireless connectivity is becoming more and more common. Nowhere is this more evident than in consumer electronics, where the mobile and tablet markets have driven the rapid adoption of a variety of wi...
1 IntroductionThe car driving recorder is a recording device used in the car. This device can record and store the vehicle's driving speed, mileage and other status information about the vehicle's dri...
PCB is closely related to downstream terminal demand, and the technology development trend is developed in response to the trend of downstream mainstream products. Mobile phone circuit boards (referre...
1. Equipment Overview
Shell-and-tube heat exchangers are a common heat exchange device used in chemical evaporation and heating equipment. Currently, the tubesheets of shell-and-tube heat exch...[Details]
In recent years, with the application of the IEC61850 standard and the development and deployment of optoelectronic transformers, the concept of digital substations has been put into practical use ...[Details]
Today's security industry has entered the era of massive networking. Many enterprises, especially financial institutions, have established multi-level video surveillance networking platforms. Lever...[Details]
The automotive industry in 2025 is undergoing a thorough intelligent reshuffle.
Geely wants to make changes in the field of AI cockpits: in the future, there will be no traditional smart...[Details]
Since its invention in the mid-1940s, the microwave oven has evolved from a humble beginning to commercial use, entering homes in the 1960s and rapidly gaining popularity. Its basic functionality a...[Details]
introduction
According to the China Fire Statistics Yearbook, electrical fires accounted for more than 30% of fire accidents in the past decade, and the trend is increasing year by year. They ...[Details]
Through AI connection technology supported by Qualcomm X85 5G modem and RF and Qualcomm FastConnect 7900 mobile connection system, seamless switching can be achieved between cellular net...[Details]
According to Nikkei, a survey found that global electric vehicle battery supply is expected to reach more than three times the required quantity due to
cooling
demand for electric vehicles,...[Details]
Tiantai Robot's official Weibo account announced on the evening of August 20 that Tiantai Robot Co., Ltd., together with strategic partners including Shandong Future Robot Technology Co., Ltd., Sha...[Details]
Preface
Low-voltage motors are widely used in nonferrous metallurgical plants. Their abnormal operation not only impacts normal production but can also threaten human life. Therefore, providin...[Details]
With growing environmental awareness, the continuous improvement of three-electric technology and the increasing deployment of infrastructure such as charging stations, the electrification of new e...[Details]
Tires are a very important component for cars. They are related to the driving experience of the vehicle. We are almost inseparable from cars in our daily lives. For tires, according to the role of...[Details]
Smartphones can be incredibly unintelligent. For example, consider an office full of people, each absorbed in their work. Suddenly, the silence is broken by a burst of loud pop music. A colleague's...[Details]
High-definition media consumption is experiencing a dual growth: an increase in the number of consumers and a transition to higher-definition content. This growth is driven by increasingly widespre...[Details]
In camera and display systems, the demand for high-performance and low-power data interfaces is driving continuous technological evolution. The evolution of MIPI D-PHY and MIPI C-PHY clearly ...[Details]
Embedded System
京公网安备 11010802033920号
EEWORLD
