EEWORLDEEWORLDEEWORLD

Part Number

Search

MHR64HSGAN

Description
Board Connector, 64 Contact(s), 2 Row(s), Male, Right Angle, 0.1 inch Pitch, Solder Terminal, Latch & Eject, Black Insulator, Receptacle
CategoryThe connector    The connector   
File Size364KB,2 Pages
ManufacturerMethode Electronics Inc.
Download Datasheet Parametric View All

MHR64HSGAN Overview

Board Connector, 64 Contact(s), 2 Row(s), Male, Right Angle, 0.1 inch Pitch, Solder Terminal, Latch & Eject, Black Insulator, Receptacle

MHR64HSGAN Parametric

Parameter NameAttribute value
Objectid1149766655
Reach Compliance Codeunknown
ECCN codeEAR99
body width0.326 inch
Body/casing typeRECEPTACLE
Connector typeBOARD CONNECTOR
Contact to complete cooperationAU
Contact completed and terminatedGOLD
Contact point genderMALE
Contact materialPHOSPHOR BRONZE
contact modeRECTANGULAR
Contact resistance20 mΩ
Contact styleSQ PIN-SKT
Dielectric withstand voltage1000VAC V
Durability750 Cycles
Insulation resistance5000000000 Ω
Insulator colorBLACK
insulator materialGLASS FILLED POLYBUTYLENE TEREPHTHALATE
JESD-609 codee4
MIL complianceYES
Plug contact pitch0.1 inch
Match contact row spacing0.1 inch
Installation option 1LATCH & EJECT
Installation option 2LOCKING
Installation methodRIGHT ANGLE
Installation typeBOARD
Number of connectorsONE
PCB row number2
Number of rows loaded2
Maximum operating temperature125 °C
Minimum operating temperature-65 °C
PCB contact patternRECTANGULAR
PCB contact row spacing2.54 mm
Plating thickness5u inch
polarization keyCENTER
GuidelineUL, CSA
reliabilityMIL-C-83503
Terminal pitch2.54 mm
Termination typeSOLDER
Total number of contacts64
TMIGS tunnel multi-information early warning and safety management system
[size=3]TMIGS system is jointly developed by Beijing Jiaotong University, Beijing Municipal Engineering Research Institute, and Beijing Sotong Zifeng Communication Engineering Technology Co., Ltd. The...
lwslxh Industrial Control Electronics
STM8L enters Halt mode. Where does the program return after being awakened by an interrupt and exiting the interrupt?
I have a basic question. I looked through the reference manual but couldn't find the answer. When STM8L enters Halt mode and is awakened by an interrupt, where does the program return to after exiting...
jiyiche stm32/stm8
Please tell me the function of these resistors
[img]http://hi.eeworld.net/attachment/201004/20/3276840_1271745733hZ5e.jpg[/img]1. What is the role of the two 15K resistors in the second stage op amp in this figure? Do they provide bias for the sec...
dudu2000 Embedded System
Is the 430 downloader powered when in use?
Is the 430 downloader powered when in use? Why can't I download the program, but can simulate it? Why?...
MSP430ZJZ MCU
Can vias be placed on pads?
I am making an RF board, and I use 0402 for resistor and capacitor packages. I put 0.2mm vias on the pads of the 0402 package, and covered the vias with oil. Is this OK? Although there will be no tin ...
943614033 PCB Design
How do you test the chip driver code you write?
I specialize in FPGA chip driver code, but I have written the code, but the chip FPGA is not yet finished. Is there any way to verify whether the code I wrote is correct? How do you usually test it?...
shangyl Embedded System

Technical ResourceMore

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2459  2742  2689  2519  3  50  56  55  51  1 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号