REVISIONS
LTR
A
B
C
D
E
DESCRIPTION
Changes in accordance with NOR 5962-R246-94.
Changes in accordance with NOR 5962-R218-96.
Add case outlines T, U, Y, and Z.
Update drawing boilerplate.
Add device type 02. For paragraph 1.3 Input voltage range, update
footnote 2/ to add “regulation may be maintained”. Table I; delete test for
“Short circuit current” Isc. Add RHA requirements for device type 02. gc
Add paragraph 1.5 and note 2. Table I, add note for enhanced low dose
rate effects. Paragraph 4.3.5.a, correct paragraph to add
component tested dose rate. -sld
Add RHA levels P and L to device type 02 in paragraphs 1.3, 1.5, 4.3.5
(table), table I, and SMD bulletin. Add paragraph 3.2.3. -gz
Table I, VT
LINE
test, change max limits 400 and 500 to ±500 and ±600,
respectively (2 places each). Table I, note 7, change "is greater than 10
microseconds" to "is equal to 100 microseconds ±20%". Figure 2, note 1,
last line, correct (pin 11) to (pin 12). Table II, add note to Group C
end-point test parameters. -gz
Figure 1, Case outline X; Changed dimension from "E1" to "E" and the
dimension from "E2" to "E1". -sld
DATE (YR-MO-DA)
94-07-25
96-09-12
98-02-23
04-07-28
06-04-05
APPROVED
K. A. Cottongim
K. A. Cottongim
K. A. Cottongim
Raymond Monnin
Raymond Monnin
F
06-12-28
Raymond Monnin
G
07-06-06
Robert M. Heber
H
10-09-23
Charles F. Saffle
J
12-06-01
Charles F. Saffle
REV
SHEET
REV
SHEET
REV STATUS
OF SHEETS
PMIC N/A
J
15
J
16
REV
SHEET
PREPARED BY
Steve L. Duncan
CHECKED BY
Michael Jones
J
1
J
2
J
3
J
4
J
5
J
6
J
7
J
8
J
9
J
10
J
11
J
12
J
13
J
14
STANDARD
MICROCIRCUIT
DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
http://www.landandmaritime.dla.mil/
THIS DRAWING IS AVAILABLE
FOR USE BY ALL
DEPARTMENTS
AND AGENCIES OF THE
DEPARTMENT OF DEFENSE
APPROVED BY
Kendall A. Cottongim
DRAWING APPROVAL DATE
94-05-23
REVISION LEVEL
J
MICROCIRCUIT, HYBRID, LINEAR, 15 VOLT,
SINGLE CHANNEL, DC-DC CONVERTER
AMSC N/A
SIZE
A
SHEET
CAGE CODE
67268
1 OF
16
5962-93161
DSCC FORM 2233
APR 97
5962-E351-12
1. SCOPE
1.1 Scope. This drawing documents five product assurance classes as defined in paragraph 1.2.3 and MIL-PRF-38534. A
choice of case outlines and lead finishes which are available and are reflected in the Part or Identifying Number (PIN). When
available, a choice of radiation hardness assurance levels are reflected in the PIN.
1.2 PIN. The PIN shall be as shown in the following example:
5962
½
½
½
Federal
stock class
designator
\
-
½
½
½
RHA
designator
(see 1.2.1)
\/
Drawing number
1.2.1 Radiation hardness assurance (RHA) designator. RHA marked devices shall meet the MIL-PRF-38534 specified RHA
levels and shall be marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device.
1.2.2 Device types. The device types identify the circuit function as follows:
Device type
01
02
Generic number
MFL2815S
SMFL2815S
Circuit function
DC-DC converter, 65 W, +15 V output
DC-DC converter, 65 W, +15 V output
93161
01
½
½
½
Device
type
(see 1.2.2)
/
H
½
½
½
Device
class
designator
(see 1.2.3)
X
½
½
½
Case
outline
(see 1.2.4)
A
½
½
½
Lead
finish
(see 1.2.5)
1.2.3 Device class designator. This device class designator shall be a single letter identifying the product assurance level.
All levels are defined by the requirements of MIL-PRF-38534 and require QML Certification as well as qualification (Class H, K,
and E) or QML Listing (Class G and D). The product assurance levels are as follows:
Device class
K
Device performance documentation
Highest reliability class available. This level is intended for use in space
applications.
Standard military quality class level. This level is intended for use in applications
where non-space high reliability devices are required.
Reduced testing version of the standard military quality class. This level uses the
Class H screening and In-Process Inspections with a possible limited temperature
range, manufacturer specified incoming flow, and the manufacturer guarantees (but
may not test) periodic and conformance inspections (Group A, B, C, and D).
Designates devices which are based upon one of the other classes (K, H, or G)
with exception(s) taken to the requirements of that class. These exception(s) must
be specified in the device acquisition document; therefore the acquisition document
should be reviewed to ensure that the exception(s) taken will not adversely affect
system performance.
Manufacturer specified quality class. Quality level is defined by the manufacturers
internal, QML certified flow. This product may have a limited temperature range.
H
G
E
D
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
SIZE
A
REVISION LEVEL
J
5962-93161
SHEET
2
DSCC FORM 2234
APR 97
1.2.4 Case outlines. The case outlines are as designated in MIL-STD-1835 and as follows:
Outline letter
T
U
X
Y
Z
Descriptive designator
See figure 1
See figure 1
See figure 1
See figure 1
See figure 1
Terminals
12
12
12
12
12
Package style
Tabbed flange mount, lead formed up
Flange mount, lead formed down
Flange mount, short lead
Tabbed flange mount, short lead
Tabbed flange mount, lead formed down
1.2.5 Lead finish. The lead finish shall be as specified in MIL-PRF-38534.
1.3 Absolute maximum ratings. 1/
Input voltage range (V
IN
) 2/ ........................................................
Power dissipation (P
D
):
Device types 01 and 02 (non-RHA) ........................................
Device type 02 (RHA level P, L, and R) ................................
Lead soldering temperature (10 seconds) .................................
Storage temperature range ........................................................
1.4 Recommended operating conditions.
Input voltage range (V
IN
) ............................................................
Output power .............................................................................
Case operating temperature range (T
C
) .....................................
1.5 Radiation features.
Maximum total dose available (dose rate = 9 rad(Si)/s):
Device type 02 (RHA levels P, L, and R) ...............................
2. APPLICABLE DOCUMENTS
2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part
of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the
solicitation or contract.
DEPARTMENT OF DEFENSE SPECIFICATION
MIL-PRF-38534 - Hybrid Microcircuits, General Specification for.
DEPARTMENT OF DEFENSE STANDARDS
MIL-STD-883 - Test Method Standard Microcircuits.
MIL-STD-1835 - Interface Standard for Electronic Component Case Outlines.
+16 V dc to +40 V dc
£
65 W
-55°C to +125°C
-0.5 V dc to +50 V dc
16 W
18 W
+300°C
-65°C to +150°C
100 krad (Si) 3/
1/
2/
3/
Stresses above the absolute maximum ratings may cause permanent damage to the device. Extended operation at the
maximum levels may degrade performance and affect reliability.
An undervoltage lockout circuit shuts the unit off when the input voltage drops to approximately 12 volts. Operation of the
unit between 12 volts and 16 volts is nondestructive. At reduced output power, regulation may be maintained, but
performance is not guaranteed.
These parts may be dose rate sensitive in a space environment and may demonstrate enhanced low dose rate effects.
Radiation end-point limits for the noted parameters are guaranteed only for the conditions as specified in MIL-STD-883,
method 1019, condition C, tested at 9 rad(Si)/s.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
SIZE
A
REVISION LEVEL
J
5962-93161
SHEET
3
DSCC FORM 2234
APR 97
DEPARTMENT OF DEFENSE HANDBOOKS
MIL-HDBK-103 - List of Standard Microcircuit Drawings.
MIL-HDBK-780 - Standard Microcircuit Drawings.
(Copies of these documents are available online at
https://assist.daps.dla.mil/quicksearch/
or from the Standardization
Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.)
2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text
of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a
specific exemption has been obtained.
3. REQUIREMENTS
3.1 Item requirements. The individual item performance requirements for device classes D, E, G, H, and K shall be in
accordance with MIL-PRF-38534. Compliance with MIL-PRF-38534 may include the performance of all tests herein or as
designated in the device manufacturer's Quality Management (QM) plan or as designated for the applicable device class. The
manufacturer may eliminate, modify or optimize the tests and inspections herein, however the performance requirements as
defined in MIL-PRF-38534 shall be met for the applicable device class. In addition, the modification in the QM plan shall not
affect the form, fit, or function of the device for the applicable device class.
3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified
in MIL-PRF-38534 and herein.
3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.4 herein and figure 1.
3.2.2 Terminal connections. The terminal connections shall be as specified on figure 2.
3.2.3 Radiation exposure circuit. The radiation exposure circuit shall be maintained by the manufacturer under document
revision level control and shall be made available to the preparing and acquiring activity upon request.
3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are
as specified in table I and shall apply over the full specified operating temperature range.
3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical
tests for each subgroup are defined in table I.
3.5 Marking of devices. Marking of devices shall be in accordance with MIL-PRF-38534. The device shall be marked with
the PIN listed in 1.2 herein. In addition, the manufacturer's vendor similar PIN may also be marked.
3.6 Data. In addition to the general performance requirements of MIL-PRF-38534, the manufacturer of the device described
herein shall maintain the electrical test data (variables format) from the initial quality conformance inspection group A lot sample,
for each device type listed herein. Also, the data should include a summary of all parameters manually tested, and for those
which, if any, are guaranteed. This data shall be maintained under document revision level control by the manufacturer and be
made available to the preparing activity (DLA Land and Maritime-VA) upon request.
3.7 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to supply to this
drawing. The certificate of compliance (original copy) submitted to DLA Land and Maritime-VA shall affirm that the
manufacturer's product meets the performance requirements of MIL-PRF-38534 and herein.
3.8 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38534 shall be provided with each lot of
microcircuits delivered to this drawing.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
SIZE
A
REVISION LEVEL
J
5962-93161
SHEET
4
DSCC FORM 2234
APR 97
TABLE I. Electrical performance characteristics.
Test
Symbol
Conditions 1/ 2/
-55°C
£
T
C
£
+125°C
V
IN
= 28 V dc ±0.5 V dc
no external sync
unless otherwise specified
I
OUT
= 4.33 A dc
Group A
subgroups
Device
type
Min
Limits
Max
Unit
Output voltage
V
OUT
1
2,3
1,2,3
1,2,3
1,2,3
1
2,3
1,2,3
1,2,3
1,2,3
1,2,3
P,L,R
1,2,3
1,2,3
1,2,3
1,2,3
1,2,3
1,2,3
1,2,3
1
2,3
1,2,3
1
01,02
14.85
14.55
14.48
0.0
0.0
15.15
15.45
15.87
4.33
4.33
85
110
135
20
30
20
20
100
V
P,L,R
Output current
I
OUT
V
IN
= 16 V dc to 40 V dc
P,L,R
Output ripple voltage
V
RIP
I
OUT
= 4.33 A,
BW = 10 kHz to 2 MHz
P,L,R
Line regulation
VR
LINE
I
OUT
= 4.33 A,
V
IN
= 16 V dc to 40 V dc
P,L,R
I
OUT
= 0 to 4.33 A
I
OUT
= 0 A, inhibit (pins 4 and
12) = open
P,L,R
I
OUT
= 0 A, inhibit 1 (pin 4)
tied to input return (pin 2)
P,L,R
I
OUT
= 0 A, inhibit 2 (pin 12)
tied to output return (pin 8)
P,L,R
Input ripple current
I
RIP
I
OUT
= 4.33 A,
BW = 10 kHz to 10 MHz
P,L,R
Efficiency
Eff
I
OUT
= 4.33 A
02
01,02
02
01,02
A
mV p-p
02
01,02
02
01,02
02
01,02
02
01,02
02
01,02
02
01,02
mV
Load regulation
VR
LOAD
mV
Input current
I
IN
mA
125
14
17
70
90
45
50
75
84
82
82
80
79
%
mA p-p
02
01
02
2,3
01
02
P,L,R
See footnotes at end of table.
1,2,3
02
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
SIZE
A
REVISION LEVEL
J
5962-93161
SHEET
5
DSCC FORM 2234
APR 97
京公网安备 11010802033920号
EEWORLD
