EEWORLDEEWORLDEEWORLD

Part Number

Search

WBDDSS8-B-07-1092-C-C

Description
Array/Network Resistor, Bussed, 0.05W, 10900ohm, 100V, 0.25% +/-Tol, -25,25ppm/Cel, 1408,
CategoryPassive components    The resistor   
File Size273KB,4 Pages
ManufacturerTT Electronics plc
Websitehttp://www.ttelectronics.com/
Download Datasheet Parametric View All

WBDDSS8-B-07-1092-C-C Overview

Array/Network Resistor, Bussed, 0.05W, 10900ohm, 100V, 0.25% +/-Tol, -25,25ppm/Cel, 1408,

WBDDSS8-B-07-1092-C-C Parametric

Parameter NameAttribute value
Objectid820067416
Reach Compliance Codecompliant
ECCN codeEAR99
structureChip
Network TypeBussed
Number of terminals16
Maximum operating temperature150 °C
Minimum operating temperature-55 °C
Package height0.406 mm
Package length3.556 mm
Package formSMT
Package width2.032 mm
method of packingTray
Rated power dissipation(P)0.05 W
GuidelineMIL-PRF-38534
resistance10900 Ω
Resistor typeARRAY/NETWORK RESISTOR
seriesWBC-NETWORK
size code1408
Temperature Coefficient-25,25 ppm/°C
Tolerance0.25%
Operating Voltage100 V
Wire Bondable
Resistor Network Arrays
Chip Network Array Series
·
·
·
·
Absolute tolerances to ±0.1%
Tight TCR tracking to ±5ppm/°C
Ratio match tolerances to ±0.05%
Ultra-stable tantalum nitride resistors
IRC’s TaNSil
®
network array resistors are ideally suited for applications that demand a small footprint. The small wire
bondable chip package provides higher component density, lower resistor cost and high reliability.
The tantalum nitride film system on silicon provides precision tolerance, exceptional TCR tracking and low cost.
Excellent performance in harsh, humid environments is a trademark of IRC’s self-passivating TaNSil
®
resistor film.
For applications requiring high performance resistor networks in a low cost, wire bondable package, specify IRC
network array die.
General Note
TT electronics reserves the right to make changes in product specification without notice or liability.
All information is subject to TT electronics’ own data and is considered accurate at time of going to print.
www.bitechnologies.com www.irctt.com www.welwyn-tt.com
© TT electronics plc
10. 11
How to avoid getting into trouble when designing circuits for bridge sensors
[i=s] This post was last edited by Tonglinniao on 2015-4-17 16:15 [/i] [align=left][color=#0000ff][b]Reprinted from ADI Chinese Technical Forum: [/b][/color][url=https://ezchina.analog.com/message/243...
同林鸟 Integrated technical exchanges
Power simulation round 2: pspice
What should I use for power supply simulation? Pspise, Matlab, or Saber? Not sure which one is suitable? I have selected the software but don't know how to use it? Look here, Guanguan has carefully co...
okhxyyo Power technology
stm32 CANOpen
Below is a comparison between the CAN protocol and the OSI network model. The CAN physical layer is divided into three layers: MDI, PMA and PLS, and the data link layer is divided into two layers: MAC...
gandong stm32/stm8
Where can I download Philip's Emebest IDE?
Where can I download Philip's Emebest IDE? I'm planning to work on ARM....
aphonline Embedded System
[Ultra-low power STM32U5 IoT exploration kit]
Development board hardware: Functional diagram 6-layer PCB design, open source, YYDS The main control chip is: The STM32U585 microcontroller uses an Arm Cortex-M33 processor core running at 160 MHz, s...
mameng stm32/stm8

Technical ResourceMore

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1217  1159  107  1197  366  25  24  3  8  29 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号