Contact Resistance Variation ...........................±1 % .................................................................±3 % of total resistance or 3 ohms
(whichever is greater)
Dielectric Withstanding Voltage (MIL-STD-202, Method 301)
Total Resistance Shift ................................... ±10 % maximum ................................................ ±3 % maximum
Rotational Life (No Load) ................................... 100,000 cycles ................................................... 20,000 cycles
Total Resistance Shift ................................... ±15 % TRS maximum ....................................... ±5 % or 5 ohms TRS whichever is greater
Torque (Starting and Running)..................................................................................... A & B bushings 0.35 to 4.23 N-cm (0.05 to 6.0 oz.-in.)
C & E bushings 0.21 to 4.23 N-cm (0.3 to 6.0 oz.-in.)
3856 – 0.11 to 2.12 N-cm (0.15 to 3.0 oz.-in.)
Mounting (Torque on Bushing) ........................................................................................................... 1.7-2.0 N-m (15-18 lb.-in.) maximum
Weight (Single Section) ......................................................................................................................................................30 grams maximum
Terminals ................................................................................................................................................ Printed circuit terminals or solder lugs
Soldering Condition ............................................Recommended hand soldering using Sn95/Ag5 no clean solder, 0.025 ˝ wire diameter.
Maximum temperature 399 °C (750 °F) for 3 seconds. No wash process to be used with no clean flux.
Part can be wave soldered at 260 °C (500 °F) for 5 seconds, no wash process with no clean flux.
Marking...........................................................................Manufacturer’s trademark, wiring diagram, resistance, date code, and part number
Ganging (Multiple Section Potentiometers) ..............................................................................................................................1 cup maximum
Hardware.................................................................................... One lockwasher and one mounting nut is shipped with each potentiometer;
locking bushing versions are shipped with one additional locking nut
specifications tested at 250 RPM, at room ambient: +25 °C nominal.
Specifications are subject to change without notice.
Users should verify actual device performance in their specific applications.
The products described herein and this document are subject to specific legal disclaimers as set forth on the last page of this document, and at www.bourns.com/docs/legal/disclaimer.pdf.
3851/3852/3856 – 3/4 ˝ Diameter Panel Control
Product Dimensions
9.53
(.38)
.38
(.015)
12.7, 22.23
STD.
(1/2, 7/8)
3/8-32 UNEF
.25
45
°
X
(.010)
CHAMFER
6.35+.03/-.05
DIA.
(.250+.001/-.002)
SHAFT SLOT
1.19
.047 WIDE X
1.60+.38/.00
DEEP
(.063+.015/-.000)
6.35
±
.76
(.25
±
.03)
12.7
(.50)
.38
(.015)
15.88
STD.
(5/8)
3/8-32 UNEF
.25
45
°
X
(.010)
CHAMFER
6.35+.03/-.05
DIA.
(.250+.001/-.002)
SHAFT SLOT
1.19 WIDE X
(.047)
1.60+.38/-.00
(.063+.015/-.000)DEEP
6.35
±
.76
(.25
±
.03)
19.05
(.75)
DIA.
12.19
DIA.
(.480)
19.05
(.75)
DIA.
12.19
DIA.
(.48)
SOLDER LUG TERMINAL
6.35
2.79
(.25)
TYP.
(.110)
3 PLCS.
12.7
(.50)
EACH TERMINAL LUG
2
3
2 PLCS.
1
WILL ACCOMMODATE
.72
THREE
(.028)
DIAMETER
14.02
±
.25
(.724 DIA. AWG
(.552
±
.010)
STRANDED) WIRES.
STANDARD
PRINTED CIRCUIT TERMINAL
1.02
6.35
TYP.
TYP.
(.040)
(.25)
15.88
±
.38
(.625
±
.015)
16.00
5.49
OPTIONAL FLAT
(.63)
(.216)
1.52
28.58
LONG OR
FRONT BUSHING FOR SHAFTS UNDER
(.06)
(1-1/8)
1
2
3
6.35
(.25)
6.35
(.25)
9.53, 22.23
STD.
(3/8, 7/8)
.38
(.015)
2.36
(.094)
1/4-32 UNEF
.25
45
°
X (.010)
CHAMFER
6.35
±
.76
(.25
±
.03)
9.53
(.38)
.38
(.015)
12.7
STD.
(1/2)
1/4-32 UNEF
.25
45
°
X (.010)
CHAMFER
6.35
±
.76
(.25
±
.03)
SUGGESTED BOARD LAYOUT
6.35
6.35
(.25)
(.25)
1.40
DIA.
(.055)
19.05
(.75)
DIA.
12.19
DIA.
(.480)
19.05
(.75)
DIA.
3.18
±
0.25
DIA.
(.125
±
.001)
3.18
±
.025
DIA.
(.125
±
.001)
SHAFT SLOT
.79 WIDE X .76 DEEP
(.031)
(.03)
.25
OPTIONAL FLAT
LONG OR
(.010)
1.52
15.88
FRONT BUSHING FOR SHAFTS UNDER
(.06)
(5/8)
SHAFT SLOT
.79 WIDE X .76 DEEP
(.03)
(.031)
12.19
DIA.
(.480)
A, B & H BUSHINGS
9.53
(.375)
C & E BUSHINGS
9.53
(.375)
9.91
DIA.
(.390)
3.18
DIA.
(.125)
3.18
6.73
DIA.
(.125)DIA.
(.265)
9.53
(.38)
6.35
±
.76
(.25
±
.03)
12.7
(.50)
.38
(.015)
6.35+.03/-.05
DIA.
(.250+.001/-.002)
3/8-32 UNEF
1.19
(.047)
9.53
(.38)
6.35
±
.76
(.25
±
.03)
.38
(.015)
12.7
(.50)
6.35+.03/-.05
DIA.
(.250
±
.03)
3/8-32 UNEF.
.79
(.031)
SHAFT SLOT
ALIGNMENT
AT CCW
FLAT
ALIGNMENT
AT CCW
50
° ±
10
°
50
° ±
10
°
19.05
(.75)
DIA.
12.19
DIA.
(.480)
1.60+3.81/-.000
(.063+.015/-.000)
DIA.
22.23
STD.
(7/8)
19.05
(.75)
DIA.
12.19
DIA.
(.480)
.79
±
.25
(.031
±
.010)
22.23
STD.
(7/8)
3.18
±
.03
(.125
±
.003)
DIA.
.25
45
°
X (.010)
CHAMFER
2.67
±
.381
(.105
±
.015)
ANTI-ROTATION LUG
PROJECTS 1/16 INCH
ABOVE MOUNTING FACE.
TOLERANCES EXCEPT AS NOTED:
.127
.XX
±
.38
DECIMALS: .XXX
±
(.005),
(.015)
FRACTIONS:
±
1/64
ANGLE:
±
3 %
.25
45
°
X (.010)
CHAMFER
DIMENSIONS:
MM
(INCHES)
CCW
1
3
Specifications are subject to change without notice.
Users should verify actual device performance in their specific applications.
The products described herein and this document are subject to specific legal disclaimers as set forth on the last page of this document, and at www.bourns.com/docs/legal/disclaimer.pdf.
POTENTIOMETER
2
3851/3852/3856 – 3/4 ˝ Diameter Panel Control
Hardware
LOCKWASHER H-37-1
6.6
(.26)
NUT H-38-1
9.53 +0/-0.38
(.375 +0/-.015)
2.36 ± 0.25
(.093 ± .01)
LOCKNUT H-38-3
4.57 ± 0.05
(.180 ± .002)
7.75
(.305)
11 +0/-0.43
(.433 +0/-.017)
NUT H-38-2
2.36 ± 0.25
(.093 ± .01)
30 ° ± 5 °
1.02
(.040)
30 ° ± 5 °
TYP.
0.64
(.025)
15 ° ± 1 °
1/4-32 UNEF
1/4-32
NEF-20
12.07 ± 0.25
(.475 ± .01)
LOCKWASHER H-37-2
9.58 ± 0.36
(.377 ± .014)
0.64 ± 0.05
(.025 ± .002)
7.92
(.312)
3/8-32 NEF-2B
3.96
(.156)
12.52 ± 0.36
(.493 ± .014)
0.56 ± 0.05
(.022 ± .002)
14.66 +0/-0.43
(.577 +0/-.017)
30 ° ± 5 °
Date Code Description
YYWWM
M = COUNTRY OF MANUFACTURE
(MEXICO)
WW = WEEK NUMBER
YY = LAST TWO DIGITS OF YEAR
MANUFACTURED
DIMENSIONS:
MM
(INCHES)
LOCKNUT H-38-4
8.51 ± 0.05
(.335 ± .002)
1.91
MIN.
(.075)
18 ° ± 2 °
3/8-32
NEF-2B
1.02
(.040)
12.7
(.5)
1.14 ± 0.38
(.045 ± .015)
30 ° ± 5 ° TYP.
4.83
(.19)
Specifications are subject to change without notice.
Users should verify actual device performance in their specific applications.
The products described herein and this document are subject to specific legal disclaimers as set forth on the last page of this document, and at www.bourns.com/docs/legal/disclaimer.pdf.
3851/3852/3856 – 3/4 ˝ Diameter Panel Control
How To Order
3852
A
-
28
2
-
103
A
L
12
16
16
20
28
28
SHAFT TYPE
(FMS) & DIAMETER
3/8 ” (9.53 mm) L X 1/8 ” (3.18 mm) D
1/2 ” (12.7 mm) L x 1/4 ” (6.35 mm) D
1/2 ” (12.7 mm) L x 1/8 ” (3.18 mm) D
5/8 ” (15.88 mm) L X 1/4 ” (6.35 mm) D
7/8 ” (22.20 mm) L X 1/4 ” (6.35 mm) D
7/8 ” (22.20 mm) L X 1/8 ” (3.18 mm) D
AVAILABLE ONLY IN
MODELS
3851, 3852
3851, 3852
3851, 3852
3851, 3852
3851, 3852
3856
3851, 3852
3856
BUSHINGS
C
A
C, E
A, B
A, B
A
C, E
H
Consult factory for lengths not shown.
A
B
C
E
H
BUSHING
Plain 3/8 ” (9.53 mm) D x 3/8 ” (9.53 mm) L
Locking 3/8 ” (9.53 mm) D x 1/2 ” (12.7 mm) L
Plain 1/4 ” (6.35 mm) D x 1/4 ” (6.35 mm) L
Locking 1/4 ” (6.35 mm) D x 1/2 ” (12.7 mm) L
Plain 3/8 ” (9.53 mm) D x 3/8 ” (9.53 mm) L
APPLICABLE MODELS
3851, 3852, 3856
3851, 3852
3851, 3852
3851, 3852
3856 (3.18 mm D Shaft)
RESISTANCE
CODE/VALUE
(IN OHMS)
Model 3851
(102)
1K
(252)
2.5 K
(502)
5K
(103)
10 K
(253)
25 K
(503)
50 K
(104)
100 K
(254)
250 K
(504)
500 K
(105)
1M
Models 3852/3856
(101)
100
(251)
250
(501)
500
(102)
1K
(252)
2.5 K
(502)
5K
(103)
10 K
(253)
25 K
(503)
50 K
(104)
100 K
(254)
250 K
(504)
500 K
(105)
1M
ELEMENT
TAPER/TOLERANCE
A
Linear ±10 %
B
Linear ±20 %
C
Audio CW ±10 %
D
Audio CW ±20 %
E
Linear ±10 %
F
Audio CCW ±10 %
G
Audio CCW ±20 %
H
Linear ±5 %
RoHS IDENTIFIER
L
Compliant
MODEL
3851 3/4 ” (19.05 mm) D Single-Turn C.P.
3852 3/4 ” (19.05 mm) D Single-Turn Cermet
3856 3/4 ” (19.05 mm) D 3-3/4-Turn Cermet
TERMINAL STYLE AND
SHAFT TYPE
1
2
3
5
6
7
Solder Lugs, Plain End
Solder Lugs, Slotted End
Solder Lugs, Flatted Shaft
PC Pins, Plain End
PC Pins, Slotted End
PC Pins, Flatted Shaft
Boldface features are Bourns standard options.
All others are available with higher minimum order
quantities.
APPLICABLE
MODELS
3852, 3856
3851
3852, 3856
3851
3851
3852, 3856
3851
3852, 3856
Asia-Pacific:
Tel: +886-2 2562-4117 • Email: asiacus@bourns.com
EMEA:
Tel: +36 88 885 877 • Email: eurocus@bourns.com
The Americas:
Tel: +1-951 781-5500 • Email: americus@bourns.com
www.bourns.com
REV. 10/20
Specifications are subject to change without notice.
Users should verify actual device performance in their specific applications.
The products described herein and this document are subject to specific legal disclaimers as set forth on the last page of this document, and at www.bourns.com/docs/legal/disclaimer.pdf.
As a simulator, it must be playable to pass. So it is not enough to just demonstrate the Demo Mario, but also to make him under my control! On the previous Ti board, I stopped before the handle contro...
[align=center][size=5]How to read circuit diagrams Recommended resources 18. [color=rgb(0, 0, 0)][backcolor=rgb(237, 235, 235)][font=微软雅黑]Teach you to read power circuit diagrams[/font][/backcolor][/c...
When learning something, you must strike while the iron is hot, so that you can make progress faster. So today, I will continue to share with you my experiment of using a host computer to control a sm...
The MSP430 series of microcontrollers are famous for their low power consumption and rich peripheral modules. For capacitive touch applications, the PIN RO capacitive touch detection method of MSP430 ...
Introduction Nowadays, there are more and more portable electronic devices on the market, but the power capacity and power consumption of the devices are far from meeting the market requirements, whic...
If the ultimate form of a car is a silicon-based life form, then in
the field of
intelligent driving
, it has gradually taken on the appearance of a "veteran driver." In
the field of
the ...[Details]
Flip-chip and ball grid array (BGA) are two widely used packaging technologies in the electronics industry. Each has its own advantages and limitations, and in some cases, they can complement each ...[Details]
Limited vocabulary recognition
According to the number of characters, words or short sentences in the vocabulary, it can be roughly divided into: less than 100 is small vocabulary; 100-1000 is...[Details]
According to foreign media reports, BMW has just been granted a patent for a screen that could cover the entire roof. BMW hopes to transform at least a portion of the vehicle's headliner into a dis...[Details]
The MCX E series is the most reliability- and safety-focused series in NXP's extensive MCX product portfolio.
With the launch of this series, NXP has further enriched its 5V-compatible MCU pr...[Details]
The difference between a series inverter and a parallel inverter is that they use different oscillation circuits. A series inverter connects L, R, and C in series, while a parallel inverter connect...[Details]
In the period after the switching power supply achieved the "20 kHz" revolution in the 1970s, although improvements and enhancements were made in circuit technology, the development level of the se...[Details]
Inverter power supplies on the market can generally be divided into two categories: sine wave inverters and square wave inverters. Some engineers also like to categorize pure sine wave inverters as...[Details]
As the range of electric vehicles continues to increase, driving electric vehicles for long-distance travel has become a trend. For high-speed travel, how much impact will high-speed driving of ele...[Details]
As a pioneer in the new smart home concept, robot vacuums have captured a significant market share. Robot vacuums, also known as automatic sweepers, smart vacuums, or robot vacuums, are smart home ...[Details]
On August 18th, China's largest expressway
charging station,
the G25 Changshen Expressway Tonglu Service Area (South Area), officially opened and launched its integrated solar-storage-charg...[Details]
While aberration theory is a vast subject, a basic understanding of some fundamental concepts can make it easier to understand: spherical aberration, astigmatism, field curvature, and chromatic abe...[Details]
Anyone who has driven a pure electric vehicle will find that it starts much faster than a fuel vehicle. So why do pure electric vehicles start so quickly?
We all know that an engine's to...[Details]
Shock absorbers, as the name implies, are responsible for cushioning and absorbing shocks in a car. So how much do you know about shock absorbers and how to replace them in electric cars?
...[Details]
According to a comprehensive report from Electronics Fans Network on August 4th, Lens Technology disclosed its latest progress in the humanoid field during an interview. Lens Technology stated that...[Details]
ARM Technology
京公网安备 11010802033920号
EEWORLD
