85/86 – 5/8 ˝ Square Single-Turn Panel Control with Rotary Switch
Potentiometer Specifications
Standard Resistance Range
Linear Tapers (A, B, E, & H)......................................................................... (B & E) 1 K ohms to 1 megohm ................. (A & H) 100 ohms to 1 megohm
Audio Tapers (C, D, F, G, S, & T) ................................................................ (D, G, S, & T) 1 K ohms to 1 megohm ....... (C & F) 1 K ohms to 1 megohm
Total Resistance Tolerance................................................................................. ±20 % or 10 %............................................ ±10 % or 5 %
Operating Temperature Range ........................................................................... -40 °C to +125 °C ....................................... -40 °C to +125 °C
Storage Temperature Range .............................................................................. -55 °C to +125 °C ....................................... -55 °C to +125 °C
Temperature Coefficient Over Storage Temperature Range .............................. ±1,000 ppm/°C ........................................... ±150 ppm/°C
Vibration (Single Section) ................................................................................... 15 G ........................................................... 15 G
Total Resistance Shift .................................................................................. ±2 % maximum .......................................... ±2 % maximum
Voltage Ratio Shift ....................................................................................... ±5 % maximum .......................................... ±5 % maximum
Shock (Single Section) ....................................................................................... 30 G ........................................................... 30 G
Total Resistance Shift .................................................................................. ±2 % maximum .......................................... ±2 % maximum
Voltage Ratio Shift ....................................................................................... ±5 % maximum .......................................... ±5 % maximum
Load Life ............................................................................................................. 1,000 hours ................................................ 1,000 hours
Total Resistance Shift .................................................................................. ±10 % maximum ........................................ ±5 % maximum
Rotational Life (No Load).................................................................................... 100,000 cycles ........................................... 100,000 cycles
Total Resistance Shift .................................................................................. (Linear taper) 10 ohms or .......................... (All tapers) ±5 % TRS maximum
Moisture Resistance (MIL-STD-202, Method 103, Condition B)
Total Resistance Shift .................................................................................. (B & E tapers) ±10 % maximum ................ ±5 % maximum (all tapers)
Starting and Running Torque (Non-Locking Bushings)
Single Section..................................................................................................................................................................................0.14 to 1.06 N-cm (0.2 to 1.5 oz.-in.)
Dual Section ....................................................................................................................................................................................0.14 to 1.06 N-cm (0.2 to 1.5 oz.-in.)
Triple Section ...................................................................................................................................................................................0.35 to 1.41 N-cm (0.5 to 2.0 oz.-in.)
Quadruple Section ...........................................................................................................................................................................0.35 to 1.41 N-cm (0.5 to 2.0 oz.-in.)
Starting and Running Torque (Locking Bushings) ....................................................................................................................0.14 to 2.82 N-cm (0.2 to 4.0 oz.-in.)
Shaft Locking Torque with Locknut @ 10 in-lb. (B & E Bushings) .......................................................................................................................14 N-cm (20 oz-in.)
Mounting ...................................................................................................................................................................................1.7-2.0 N-m (15-18 lb.-in.) maximum
Weight (Single Section) ............................................................................................................................................................................................. 21 grams maximum
(Each Additional Section)...................................................................................................................................................................................... 6 grams maximum
Terminals ...........................................................................................................................................................................................Printed circuit terminals or J-Hooks
Soldering Condition .................................................................................. Recommended hand soldering using Sn95/Ag5 no clean solder, 0.025 ˝ wire diameter.
Maximum temperature 399 °C (750 °F) for 3 seconds. No wash process to be used with no clean flux.
Marking ...........................................................................................Manufacturer’s trademark, wiring diagram, date code and resistance, manufacturer’s part number
Ganging (multiple section potentiometers) ...................................................................................................................................................................... 4 cup maximum
Hardware ...............One lockwasher and one mounting nut is shipped with each potentiometer; locking bushing versions are shipped with one additional locking nut
For dimensional drawings see pages 3 & 4. For ordering information see page 5.
NOTE: Model 81/82 performance specifications do not apply to units subjected to printed circuit board cleaning procedures.
1
Electrical specifications tested at 250 RPM, at room ambient: +25 °C nominal.
Initial Electrical Characteristics
1
Conductive Plastic Element
Cermet Element
Environmental Characteristics
1
Mechanical Characteristics
WARNING
Cancer and Reproductive Harm
www.P65Warnings.ca.gov
*RoHS Directive 2015/863, Mar 31, 2015 and Annex.
Specifications are subject to change without notice. Users should verify actual device performance in their specific
applications. The products described herein and this document are subject to specific legal disclaimers as set forth on the
last page of this document, and at www.bourns.com/docs/legal/disclaimer.pdf.
81/82 – 5/8 ˝ Square Single-Turn Panel Control
85/86 – 5/8 ˝ Square Single-Turn Panel Control with Rotary Switch
Rotary Switch Specifications
Initial Electrical Characteristics
1
Contacts:
DPST ............................................................................................................................................................................. N.O/N.O.,N.C./N.C. or N.O./N.C.
Power Rating (Resistive Load):
DPST ..........................................................................................................2 A @ 125 volts RMS-60 Hz or 2 A @ 28 VDC, 1 A @ 250 volts RMS-60 Hz
Operating Temperature Range ...................................................................................................................................................................... -40 °C to +70 °C
Storage Temperature Range ....................................................................................................................................................................... -65 °C to +125 °C
Vibration (Dual Section)......................................................................................................................................................................................................8 G
(Triple Section) ..................................................................................................................................................................................................5 G
(Quadruple Section) ..........................................................................................................................................................................................3 G
Contact Resistance .......................................................................................................................................................................10 milliohms maximum
Contact Bounce ......................................................................................................................................................................... 0.1 millisecond maximum
Shock (Dual Section) ........................................................................................................................................................................................................20 G
(Triple Section) ....................................................................................................................................................................................................15 G
(Quadruple Section) ............................................................................................................................................................................................10 G
Contact Resistance .......................................................................................................................................................................10 milliohms maximum
Contact Bounce ......................................................................................................................................................................... 0.1 millisecond maximum
Switch Actuating Torque (50% Duty cycle @ Rated Power Load) .................................................................................1.41 to 4.94 N-cm (2 to 7 oz.-in.)
Contact Resistance .....................................................................................................................................................................100 milliohms maximum
Moisture Resistance (MIL-STD-202, Method 106, Condition B)
Contact Resistance (0.1 VDC-10 mA) ..........................................................................................................................................10 milliohms maximum
Switch Housing Material ................................................................................................................. High temperature, flame retardant, thermosetting plastic
Mechanical Characteristics
1
Actuating Torque (Each Section, Switch Module Only) ......................................................................................................3.53 to 10.6 N-cm (5 to 15 oz.-in.)
Running Torque (Out of Detent, 2-4 Module Assembly) ....................................................................................................0.21 to 1.41 N-cm (0.3 to 2 oz.-in.)
Detent ....................................................................................................................................................................................................CW or CCW standard
Contact Materials......................................................................................................................................................................... Fine silver with gold overlay
Terminal Styles .................................................................................................................................................................................................Solder lug only
Standard Orientation .............................................................................................................................................................In-line with control terminals
Optional .........................................................................................................................................................................Rotated 90 ° CCW from standard
Terminal Strength (Before and After Soldering Heat Exposure) ........................................................................................................ 0.9 Kg (2 lbs.) minimum
1
NOTE: Model 81/82 performance specifications do not apply to units subjected to printed circuit board cleaning procedures.
Electrical specifications tested at 250 RPM, at room ambient: +25 °C nominal.
Specifications are subject to change without notice.
Users should verify actual device performance in their specific applications.
The products described herein and this document are subject to specific legal disclaimers as set forth on the last page of this document, and at www.bourns.com/docs/legal/disclaimer.pdf.
Specifications are subject to change without notice.
Users should verify actual device performance in their specific applications.
The products described herein and this document are subject to specific legal disclaimers as set forth on the last page of this document, and at www.bourns.com/docs/legal/disclaimer.pdf.
Terminal outlines shown as solid lines represent PC Pins, available
on Model 81. Dashed line terminal outline represents "J" Hook,
available on Model 82.
5.97 ± .38
(.235 ± .015)
5.08 ± .38
(.200 ± .015)
12.7
(.50)
5.33 ± .76
(.210 ± .03)
10.16 ± .13
(.400 ± .005)
Note: For units with dual concentric shaft styles, a
2.54 (.100) spacer is added between the module(s) driven
by the outer shaft and those driven by the inner shaft.
For G, K, or V shafts, add the spacer between
modules 1 and 2. For L or M shafts, add the spacer
between modules 2 and 3. For N or P shafts, add the
spacer between modules 3 and 4.
SLOTTED SHAFT
*EXCLUDES MODELS 83 AND 84
DIMENSIONS:
MM
(INCHES)
Suggested Panel Layout
B
C
BUSHING
A, B & J
E
DIM A
9.91
(.39)
ANTI-ROTATION LUG
A
B
C
E
F
J
K
DIM B
7.75
(.305)
7.75
(.305)
N/A
13.49
(.531)
N/A
9.53
(.375)
9.53
(.375)
DIM C
N/A
7.75
(.305)
7.75
(.305)
N/A
N/A
N/A
9.53
(.375)
DIM D
N/A
N/A
N/A
N/A
7.75
(.305)
N/A
N/A
DIM E
2.49
(.098)
2.49
(.098)
2.49
(.098)
3.45
(.136)
2.54
(.100)
2.54
(.100)
2.54
(.100)
D
A
C, E & N
R&S
U
6.73
(.265)
10.5
(.413)
7.5
(.295)
DIMENSIONS:
MM
(INCHES)
Specifications are subject to change without notice.
Users should verify actual device performance in their specific applications.
The products described herein and this document are subject to specific legal disclaimers as set forth on the last page of this document, and at www.bourns.com/docs/legal/disclaimer.pdf.
85/86 – 5/8 ˝ Square Single-Turn Panel Control with Rotary Switch
Product Dimensions
Primary Potentiometer Module
Model 85/86
14.53
(.572)
9.58 ± .38
(.377 ± .015)
Secondary Potentiometer Module
Model 85/86
10.16
(.400)
15.88
(.625)
15.88
(.625)
Shaft Flat Orientation*
120 ° ± 5 ° CCW END
30 ° ± 5 °
12.7
(.50)
5.97
(.235)
8.56
(.337)
1.60
(.063)
FLATTED SHAFT
5.08
(.200)
SLOTTED SHAFT
*EXCLUDES MODELS 83 AND 84
5.08
(.200) 8.56
(.337)
5.08
(.200)
Switch Module
Model 85/86
REAR
PLATE
COVER
2.77
(.109)
1.35
(.053)
2.29
(.090)
TYP.
6 PLACES
Assembly Sequence
Model 85/86
Secondary Potentiometer Module
Switch Module Terminal Orientation
3
1
4
2
3
1
18.42
(.725)
2.41
1.14
(.095)L X (.045)W
SLOT TYP. 6 PLACES
4
2
HORIZONTAL ORIENTATION
(Types R56, R57, R58 & R59)
VERTICAL ORIENTATION
(Types R50, R51, R52 & R53)
2.92
(.115)
9.53
(.375)
REAR
COVER
PLATE
SWITCH
MODULE
PRIMARY
POTENTIOMETER
MODULE
4
2
3
1
3
1
4
2
DPST (NO/NC)
(TYPES 50, 51, 56, 57)
DPST (NO/NO)
(TYPES 52, 53, 58, 59)
Switch contacts shown in detent position.
Locating Lug Options - All Model 80 Series
A
.46
(.018)
7.75
(.305)
E
13.49
(.531)
J
9.53
(.375)
.79 ± .41
(.031 ± .016)
E = 2.36 ± .76
(.093 ± .03)
H & J = 1.98 ± .41
(.078 ± .016)
2.31
(.091)
3.18
(.125)
.46
(.018)
2.36
(.093)
7.75
(.305)
A
C
7.75
(.305)
.46
(.018)
.79 ± .41
(.031 ± .016)
MOUNTING
SURFACE
TOLERANCES EXCEPT AS SHOWN: DECIMAL .XXX ±
RECOMMENDED
PANEL LAYOUT
7.75
#40 DRILL
(.305)
2.49
DIA.
(.098)
9.91
DIA.
(.390)
.127
(.005)
.XX ± .38
(.015)
ANGLE ± 5 %
2.31
(.091)
DIMENSIONS:
MM
(INCHES)
NOTE: "D" OPTION - NO A/R LUG. OTHER LOCATING LUG OPTIONS AVAILABLE. CONSULT FACTORY FOR DETAILS.
Specifications are subject to change without notice.
Users should verify actual device performance in their specific applications.
The products described herein and this document are subject to specific legal disclaimers as set forth on the last page of this document, and at www.bourns.com/docs/legal/disclaimer.pdf.
According to foreign media reports, Ford Motor has applied to the U.S. Patent and Social Security Administration (USPTO) for a patent for a remote vehicle control system that may be used in future ...[Details]
Is electromagnetic radiation from electric vehicles harmful to the human body? Recently, the issue of electromagnetic radiation from electric vehicles has garnered widespread attention. However, pu...[Details]
In mobile technology, sensors are the primary input for measured signals and form a component of a sensor system. They include sensitive and transducer elements connected to carriers and circuits. ...[Details]
With the rapid adoption of smart electric vehicles, automotive chips are evolving from auxiliary control units to the foundation of the entire vehicle's intelligence. Their applications extend from...[Details]
Electric vehicles are now widespread, but they've brought with them a host of problems, the most prominent of which is charging. Small electric vehicles (EVs) are a new form of transportation in a ...[Details]
In the electronics manufacturing industry, surface mount technology (SMT) placement machines are core equipment for production lines. However, with many different models available on the market, ch...[Details]
Linear motor modules have become the "sweet spot" in various fields due to their advantages such as long stroke, fast speed, high precision, smooth operation and long life. Different models of line...[Details]
On August 22, the Wall Street Journal reported on the 21st local time that the new US government does not plan to acquire equity in semiconductor wafer foundry giant TSMC and Micron, one of the thr...[Details]
In the field of intelligent driving, regulations are becoming increasingly stringent, and the technical threshold continues to rise. Especially after the traffic accident in March 2025, the Ministr...[Details]
In daily life, when we purchase a transformer, we are faced with the installation and wiring procedures. Generally speaking, large transformers such as power transformers are equipped with speciali...[Details]
With the gradual popularization of new energy vehicles in recent years, more and more people have been able to access and purchase electric vehicles. The structure of electric vehicles is composed ...[Details]
When American cartoonist Chester Gould sketched the watch on Dick Tracy's wrist, he had no idea that science fiction would become reality 70 years later. As a comic strip artist, Gould imagined fut...[Details]
The mobile computing market is rapidly evolving, and manufacturers are fiercely competing for market share. A key area of competition is battery life, which encompasses two key aspects: how long th...[Details]
Bearing wear is a common equipment problem in the manufacturing industry. In today's world where controlling production costs is advocated, using repair technology to reduce the scrapping and repla...[Details]
Recently, UBTECH announced its patent for "robot self-battery replacement structure, device and method".
The Qichacha patent abstract shows that the robot's self-battery replacement stru...[Details]
京公网安备 11010802033920号
EEWORLD
