EEWORLDEEWORLDEEWORLD

Part Number

Search

381LX562M100A062A

Description
Aluminum Electrolytic Capacitor, Polarized, Aluminum (wet), 100V, 20% +Tol, 20% -Tol, 5600uF,
CategoryPassive components    capacitor   
File Size791KB,13 Pages
ManufacturerCDE [ CORNELL DUBILIER ELECTRONICS ]
Environmental Compliance
Download Datasheet Parametric View All

381LX562M100A062A Overview

Aluminum Electrolytic Capacitor, Polarized, Aluminum (wet), 100V, 20% +Tol, 20% -Tol, 5600uF,

381LX562M100A062A Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
Objectid1352246476
package instruction,
Reach Compliance Codecompliant
ECCN codeEAR99
capacitance5600 µF
Capacitor typeALUMINUM ELECTROLYTIC CAPACITOR
diameter35 mm
dielectric materialsALUMINUM (WET)
ESR33 mΩ
length63 mm
Manufacturer's serial number381LX
negative tolerance20%
Number of terminals2
Maximum operating temperature105 °C
Minimum operating temperature-40 °C
Package formSnap-in
polarityPOLARIZED
positive tolerance20%
Rated (DC) voltage (URdc)100 V
ripple current4700 mA
series381LX
Terminal pitch10 mm
Type 381LX / 383LX 105 °C High Ripple, Snap-In Aluminum
High Ripple, Long Life, 2, 4 and 5 pin styles available
Adding longer-life and more ripple capability to the excellent
value of Type 380L/LX capacitors, the 381L/LX readily handles
tough switching power supply input and output circuits and
motor-drive bus capacitor applications where the high surface
area of multiple units in parallel equals the ripple capability of our
Type 520C inverter-grade capacitor. Type 381LX delivers more
capacitance per can size while Type 381L gives lower ESR for the
same capacitance rating. Type 383L/LX has 4 or 5 leads for stable,
reverse-proof mounting.
Highlights
- Top performance in power supplies and motor drives
- 4 times the life of Type 380L/LX
- 2, 4 and 5 leads available
- Big selection of 42 case sizes
–40 °C to + 105 °C ≤ 315 Vdc
–25 °C to + 105 °C ≥ 350 Vdc
10 Vdc to 450 Vdc
33 µF to 150,000 µF
± 20%
≤3 √CV µA, 4 mA max, 5 minutes
Ambient Temperature
45 °C
381L
383L
381LX,
383 LX
Frequency
50 Hz
10-100 Vdc
160-450 Vdc
Low Temperature Characteristics
0.93
0.75
60 Hz
0.95
0.80
120 Hz
1.00
1.00
500 Hz
1.05
1.20
1 kHz
1.08
1.25
5 kHz
& up
1.15
1.40
2.70
2.35
60 °C
2.60
2.20
70 °C
2.50
2.00
85 °C 105°C
2.10
1.70
1.00
1.00
Specifications
Temperature Range
Rated Voltage Range
Capacitance Range
Capacitance Tolerance
Leakage Current
Ripple Current Multipliers
Impedance ratio: Z
–20⁰C
∕ Z
+25⁰C
≤ 10 (10 Vdc)
≤ 8 (16–50 Vdc)
≤ 4 (63–100 Vdc)
≤ 3 (150–450 Vdc)
3000 h at full load at 105 °C
∆ Capacitance ±20%
ESR 200% of limit
DCL 100% of limit
1000 h at 105 °C
∆ Capacitance ±20%
ESR 200% of limit
DCL 100% of limit
10 to 55 Hz, 0.06” and 10 g max, 2 h each plane
RoHS Compliant
Endurance Life Test
Shelf Life Test
Vibration
CDM Cornell Dubilier • 140 Technology Place • Liberty, SC 29657 • Phone: (864)843-2277 • Fax: (864)843-3800
The actual output voltage of the SEPIC circuit does not match the theoretical value.
As shown in the figure, Vin input is 7~12V; R3=9k ohm, R6=1K ohm;power chip XL6008 (Xinlong), FB pin voltage VFB=1.25. (Measured VFB=1.248V);theoretical output Vo=(1+R3/R6)*1.25=12.5V, but the measure...
xiaxingxing Power technology
Transistor push-pull output circuit
I would like to ask, after adding two diodes to compensate for this push-pull output circuit, a slight phase shift occurs. How can I solve this problem?...
光芒。 Analog electronics
How to use WZC Tool in Wince to configure wireless network
When configuring the wifi wireless network, I found the wireless network configuration tool WZC TOOL provided by wince. However, I compiled WZC TOOL to generate an .exe file, and then loaded it in she...
laoyuyin Embedded System
Questions about infrared chips PT2248 and PT2249
After PT2248 transmits, PT2249 receives. The corresponding pin output level seems to be not latched. It is output only when the key is pressed. How can the level output be continuous after the key is ...
gh131413 MCU
Sharing of national competition experience
I participated in electronic design competitions when I was in school, but I didn't get any results. Later, I led a team to participate in several competitions after I started working. Overall, my exp...
sjl2001 Electronics Design Contest
MCU debugging method: using serial port to realize simple shell function
There are many ways to debug MCU programs, such as software/hardware simulation, adding data printing, etc.Keil MDK, for example, supports software simulation of many microcontrollers. Without getting...
Jacktang Microcontroller MCU

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2820  136  2881  882  1563  57  3  59  18  32 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号