EEWORLDEEWORLDEEWORLD

Part Number

Search

BU-63149F3-462Z

Description
Line Driver/Receiver, 2 Driver, Hybrid, CDFP36
CategoryAnalog mixed-signal IC    Drivers and interfaces   
File Size65KB,8 Pages
ManufacturerData Device Corporation
Download Datasheet Parametric View All

BU-63149F3-462Z Overview

Line Driver/Receiver, 2 Driver, Hybrid, CDFP36

BU-63149F3-462Z Parametric

Parameter NameAttribute value
Is it Rohs certified?incompatible
Objectid1156904195
package instructionDFP, FL36,.8,100
Reach Compliance Codecompliant
Differential outputYES
Number of drives2
High level input current maximum value0.0001 A
JESD-30 codeR-XDFP-F36
JESD-609 codee0
Number of terminals36
Maximum operating temperature125 °C
Minimum operating temperature-55 °C
Minimum output swing20 V
Maximum output low current0.0034 A
Package body materialCERAMIC
encapsulated codeDFP
Encapsulate equivalent codeFL36,.8,100
Package shapeRECTANGULAR
Package formFLATPACK
power supply5 V
Maximum receive delay
Maximum slew rate520 mA
Nominal supply voltage5 V
surface mountYES
technologyHYBRID
Temperature levelMILITARY
Terminal surfaceTin/Lead (Sn/Pb)
Terminal formFLAT
Terminal pitch2.54 mm
Terminal locationDUAL
BU-63147 and BU-63149
MIL-STD-1553 DATA BUS
+5V TRANSCEIVER
DESCRIPTION
The BU-63147/49 transceiver is a com-
plete dual transmitter and receiver pair
conforming fully to MIL-STD-1553A
and 1553B. Features include: mono-
lithic design, +5V power supply voltage,
Harris or Smiths type decoder inter-
face, completely independent dual
redundant operation, and small size
(36 pin DIP). The receiver section of
the BU-63147/49 series accepts
phase-modulated bipolar data from a
MIL-STD-1553 Data Bus and pro-
duces TTL Signal data at its output.
RX DATA OUT and
RX DATA OUT
These outputs represent positive and
negative variations of the input data
signals beyond an internally fixed
threshold level. An external STROBE
input enables or disables the receiver’s
outputs.
The transmitter section accepts
bi-phase TTL signal data at its
TX DATA IN and
TX DATA IN
inputs
and produces phase-modulated
bipolar data at the TX DATA OUT and
TX DATA OUT
outputs.
The
transmitter’s output voltage level is
typically about 11Vpp. An external
input, INHIBIT, takes priority over the
transmitter inputs and disables the
transmitter when activated with a logic
“1”.
The small size, +5V power supply volt-
age,
and
compliance
with
MIL-STD-1553 simplify engineering
design, making it an excellent choice
for interfacing with any MIL-STD-1553
system.
FEATURES
+5V Power Supply
Low Power
Conforms Fully To MIL-STD-1553A
AND 1553B
Dual Transceiver
Available with MIL-STD-1760
Compliant Transmitter Voltage
Available with McAir Compatible
Waveform
36-Pin DIP
HARRIS or SMITHS I/O
Compatibility
+5 V
1553
DATA
BUS
RECEIVER STROBE
BI PHASE
TTL DATA
COMPARATOR
RX DATA OUT
RX DATA OUT
DECODER
PHASE MODULATED
BIPOLAR DATA
RX DATA IN
SHORT OR
LONG STUB
COUPLING
ISOLATION
TRANSFORMER
RX DATA IN
RECEIVER SECTION
FILTER
FILTER
COMPARATOR
TRANSMITTER SECTION
TX Data Out
SHAPING
NETWORK
TX DATA IN
TX Data Out
SHAPING
NETWORK
ENCODER
TX DATA IN
CASE/GND
TX INHIBIT
FIGURE 1. BU-63147/49 BLOCK DIAGRAM
(one
channel shown)
©
2000
Data Device Corporation
.Power amplifier circuit
9. Power amplifier circuit1. Compared with Class A power amplifier, the main advantage of Class B complementary push-pull amplifier is.No output transformer High energy efficiency No crossover distort...
fighting Analog electronics
Watch for free: How to solve the 32.0 GT/s PCIe5 test? Two experts reveal the secrets for you
The PCI Express 5.0 PHY specification has been updated, which clearly states that the PCIe Gen5 System transmitter test will no longer use a dual-port method, and it is no longer necessary to connect ...
nmg Test/Measurement
What can you do after graduating from measurement and control? ? PS: I would like to ask you some questions about embedded training
I am a student of measurement and control, and I am about to graduate, but I still don't know what I can do after graduation. I searched on Baidu and found that there are many people who can do this. ...
wubaobao1993 stm32/stm8
Embedded universal driver
Why can't I write a universal camera driver in a WinCE embedded system like I do on a PC?...
kangjianbo Embedded System
Using MSP430G2121 DIP14 TA to output 2-way PWM pins
I don't know why there is output only on P1.2 and P1.6. CCR1 corresponds to P1.2 output and CCR2 corresponds to P1.6. I now want to map the path controlled by CCR2 to P1.1, but no matter how I change ...
topguntoo Microcontroller MCU
The room temperature is 40 degrees, it's hard to fall asleep, and I'm going to upload an IC paper---written when I was getting started
[i=s]This post was last edited by wugx on 2016-8-19 22:43[/i] The xx and xxxx in this article are not garbled characters, they are just nouns----There is not much process design in the paper, mainly p...
wugx Analog electronics

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 33  754  2379  2892  1905  1  16  48  59  39 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号