The EL5197C is a fixed gain amplifier with a bandwidth of 200MHz,
making these amplifiers ideal for today’s high speed video and moni-
tor applications. The EL5197C features internal gain setting resistors
and can be configured in a gain of +1, -1 or +2. The same bandwidth is
seen in both gain-of-1 and gain-of-2 applications.
With a supply current of just 4mA and the ability to run from a single
supply voltage from 5V to 10V, these amplifiers are also ideal for
hand held, portable or battery powered equipment.
The EL5197C is also available with a disable function. Upon being
disabled, the outputs are tri-stated and the power supply current
reduces to less than 150µA. Allowing the CE pin to float, or applying
a low logic level will enable the amplifier.
For applications where board space is critical, the EL5197C is offered
in both the SOT23-5 and SOT23-6 packages, as well as an 8-pin
SOIC. The EL5197C operates over the industrial temperature range of
-40°C to +85°C.
Applications
•
•
•
•
•
•
•
•
Battery Powered Equipment
Hand Held, Portable Devices
Video Amplifier
Cable Drivers
RGB Amplifier
Test Equipment
Instrumentation
Current to Voltage Converters
Pin Configurations
SOT23-5
OUT 1
5 VS+
+
-
SOIC-8
4 IN-
NC 1
EL5197CW5
IN- 2
IN+ 3
SOT23-6
VS- 4
OUT 1
VS- 2
IN+ 3
EL5197CW6
+
-
6 VS+
EL5197CS
5 CE
4 IN-
5 NC
-
+
7 VS+
6 OUT
8 CE
Ordering Information
VS- 2
Part No
EL5197CW5-T7
EL5197CW5-T13
EL5197CW6-T7
EL5197CW6-T13
EL5197CS
EL5197CS-T7
EL5197CS-T13
Package
SOT23-5
SOT23-5
SOT23-6
SOT23-6
8-Pin SOIC
8-Pin SOIC
8-Pin SOIC
Tape &
Reel
7”
13”
7”
13”
-
7”
13”
Outline #
MDP0038
MDP0038
MDP0038
MDP0038
MDP0027
MDP0027
MDP0027
IN+ 3
February 12, 2001
Note:
All information contained in this data sheet has been carefully checked and is believed to be accurate as of the date of publication; however, this data sheet cannot be a “controlled document”. Current revisions, if any, to these
specifications are maintained at the factory and are available upon your request. We recommend checking the revision level before finalization of your design documentation.
Values beyond absolute maximum ratings can cause the device to be pre-
maturely damaged. Absolute maximum ratings are stress ratings only and
functional device operation is not implied.
11V
Supply Voltage between V
S
+ and V
S
-
Maximum Continuous Output Current
50mA
Operating Junction Temperature
125°C
Power Dissipation
Pin Voltages
Storage Temperature
Operating Temperature
Lead Temperature
See Curves
V
S
- - 0.5V to V
S
+ +0.5V
-65°C to +150°C
-40°C to +85°C
260°C
Important Note:
All parameters having Min/Max specifications are guaranteed. Typ values are for information purposes only. Unless otherwise noted, all tests are at the
specified temperature and are pulsed tests, therefore: T
J
= T
C
= T
A
.
Electrical Characteristics
V
S
+ = +5V, V
S
- = -5V, R
L
= 150Ω, T
A
= 25°C unless otherwise specified.
Parameter
AC Performance
BW
-3dB Bandwidth
A
V
= +1
A
V
= -1
A
V
= +2
BW1
SR
ts
e
n
i
n
-
i
n
+
dG
dP
V
OS
T
C
V
OS
A
E
R
F
, R
G
CMIR
+I
IN
-I
IN
R
IN
C
IN
V
O
I
OUT
t
EN
t
DIS
I
IHCE
I
ILCE
V
IHCE
0.1dB Bandwidth
Slew Rate
0.1% Settling Time
Input Voltage Noise
IN- input current noise
IN+ input current noise
Differential Gain Error
Differential Phase Error
Offset Voltage
Input Offset Voltage Temperature Coefficient
Gain Error
Internal R
F
and R
G
Common Mode Input Range
+ Input Current
- Input Current
Input Resistance
Input Capacitance
Output Voltage Swing
Output Current
Enable Time
Disable Time
CE pin Input High Current
CE pin Input Low Current
CE pin Input High Voltage for Power Down
CE = V
S
+
CE = V
S
-
V
S
+ - 0.5
0.8
0
6
-0.1
R
L
= 150Ω to GND
R
L
= 1KΩ to GND
R
L
= 10Ω to GND
Enable (selected packages only)
40
ns
ns
µA
µA
V
±3.4V
±3.8V
95
at I
N
+
Measured from T
MIN
to T
MAX
V
O
= -3V to +3V
-2
320
±3V
-60
-30
[1]
[1]
Description
Conditions
Min
Typ
200
200
200
20
Max
Unit
MHz
MHz
MHz
MHz
V/µs
ns
nV/√Hz
pA/√Hz
pA/√Hz
%
°
V
O
= -2.5V to +2.5V, A
V
= +2
V
OUT
= -2.5V to +2.5V, A
V
= -1
TBD
-2500
12
4.4
17
50
A
V
= +2
A
V
= +2
-10
0.03
0.04
1
5
1.3
400
±3.3V
1
1
45
0.5
±3.7V
±4.0V
120
60
30
2
480
10
DC Performance
mV
µV/°C
%
Ω
V
µA
µA
kΩ
pF
V
V
mA
Input Characteristics
Output Characteristics
2
EL5197C - Preliminary
EL5197C - Preliminary
Single 200MHz Fixed Gain Amplifier
Electrical Characteristics
V
S
+ = +5V, V
S
- = -5V, R
L
= 150Ω, T
A
= 25°C unless otherwise specified.
Parameter
V
ILCE
Supply
Is
ON
Is
OFF
PSRR
-IPSR
Supply Current - Enabled
Supply Current - Disabled
Power Supply Rejection Ratio
- Input Current Power Supply Rejection
No Load, V
IN
= 0V, CE = -5V
No Load, V
IN
= 0V, CE = +4.5V
DC, V
S
= ±4.75V to ±5.25V
DC, V
S
= ±4.75V to ±5.25V
55
-2
3
4
95
75
2
5
150
mA
µA
dB
µA/V
Description
CE pin Input Low Voltage for Power Up
Conditions
Min
Typ
Max
V
S
+ -3
Unit
V
1. Standard NTSC test, AC signal amplitude = 286mV
The WM signal is a digital signal with a fixed period and an indefinite duty cycle.If the counter of Timer_A works in the up-counting mode, the output adopts the output mode 7 (reset/set mode)to contr...
How to detect the rising and falling edges during AD conversion? I want the light to be on when the voltage rises and off when it falls. The voltage range is 1.2V~2.0V. Do I compare the data collected...
Because the op amp is powered by a single power supply, a bias voltage VCM1 of tens of mV must be added (why?). I see that the classic differential amplifier circuits are all grounded? Also, I used a ...
LM4907 is an audio power amplifier designed for mobile phones and other portable communication devices. It can continuously transmit 1 W of average power to an 80 ohm load , powered by a 5VDC power su...
[i=s]This post was last edited by youyou_123 on 2015-10-28 08:20[/i] I spent an entire night yesterday to successfully program the timer. I successfully put the AD sampling into the timer interrupt, l...
introduction
Since the beginning of the 21st century, the world of information has changed rapidly. Maybe a high-tech product will be released today and a better similar product will be releas...[Details]
When choosing a laptop battery, you should consider several factors, such as power, appearance, and quality.
Regarding power, we often see that a manufacturer uses values such as the number ...[Details]
In recent years, lighting has become an important area that countries around the world are targeting to promote energy conservation and environmental protection. According to statistics, about 20% ...[Details]
1 Introduction
As an emerging microfabrication technology, micro-electromechanical system (MEMS) technology has begun to be applied in various fields. It can integrate functions such as inform...[Details]
Aromatic gases are widely present in food, medicine, cosmetics and various daily chemical products, such as snacks, liquor, spices, Chinese herbal medicines, plasters, perfumes, soaps, shampoos, et...[Details]
Flooded Batteries
This battery developed in Germany can be used to power flashlights, strobe lights and toys as long as it is filled with water. This battery can be stored for 50 years and can...[Details]
Introduction
Liquid crystal, as a display device, is widely used in low-power products such as instruments, meters, and electronic equipment with its unique advantages. In the past, the displ...[Details]
Abstract: Aiming at the needs of coal-rock acoustic emission signal monitoring system, a data acquisition circuit with 24-bit resolution and 16-channel synchronous data acquisition function is desi...[Details]
Abstract: The output of high-range acceleration sensor is less than 10 mV under the excitation of small signal. The noise of traditional test system may cover such small voltage signal, so that hig...[Details]
Liquid crystal display (LCD) panels have a wide range of applications, from small portable electronic devices to large fixed devices, including digital cameras, laptops, personal data assistants, d...[Details]
Temperature compensated quartz crystal oscillator (TCXO) is widely used as a high-precision frequency source in communication systems, radar navigation systems, precision measurement and control sy...[Details]
0 Introduction
In order to improve the automation control of shortwave transmitters, so that they can automatically process from far to near, the technicians here use the ICS system to complete the ...[Details]
When the so-called "copycat phones" that flood the domestic mobile phone market move towards large screens, stereo amplifiers, touch controls, and even GPS navigation and mobile TV, the homogeneity...[Details]
introduction
LEDs continue to gain popularity in automotive applications, thanks to their long lifespan and the flexibility they offer for body styling and interior design. Some may be surpris...[Details]
1 Introduction
With the rapid economic development, my country's electricity demand has been growing at a rate of more than 20% per year. According to the current economic development trend an...[Details]
Microcontroller MCU
京公网安备 11010802033920号
EEWORLD
