U831MD2AGE datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > Mechanical and electronic products> switch> U831MD2AGE

U831MD2AGE: DescriptionPushbutton Switch, 3PDT, On-(on), Vertical, 1A, 28VDC, 11 PCB Hole Cnt, Solder Terminal, Through Hole-right Angle; CategoryMechanical and electronic products switch; File Size1017KB，16 Pages; ManufacturerITT; Websitehttp://www.ittcannon.com/

Download Datasheet Parametric View All

U831MD2AGE Overview

Pushbutton Switch, 3PDT, On-(on), Vertical, 1A, 28VDC, 11 PCB Hole Cnt, Solder Terminal, Through Hole-right Angle

U831MD2AGE Parametric

Parameter Name	Attribute value
Objectid	1166026875
Reach Compliance Code	unknown
ECCN code	EAR99
Actuator angle
Actuator length	0.273 inch
Actuator material	GLASS FILLED NYLON
Actuator type	PUSHBUTTON
body width	12.7 mm
body height	36.8554 mm
Body length or diameter	16.51 mm
Casing diameter	0.25 inch
Nozzle length	0.288 inch
Casing type	1/4-40
Center contact plating	GOLD OVER NICKEL
Contact (AC) maximum rated R load	1A@120VAC
Maximum contact current (AC)	1 A
Maximum contact current (DC)	1 A
Contact (DC) maximum rated power R load	0.4VA@20VDC
Contact (DC) maximum rated R load	1A@28VDC
Contact function	ON-(ON)
Contact resistance	0.05 mΩ
Maximum contact voltage (AC)	120 V
Maximum contact voltage (DC)	28 V
Dielectric withstand voltage	1000VAC V
Electrical life	60000 Cycle(s)
End contact material	SILVER
End contact plating	GOLD OVER NICKEL
Shell material	STAINLESS STEEL
Insulation resistance	1000000000 Ω
insulator material	GLASS FILLED NYLON
Manufacturer's serial number	8020
Installation features	THROUGH HOLE-RIGHT ANGLE
Maximum operating temperature	65 °C
Minimum operating temperature	-30 °C
PCB hole count	11
seal	EPOXY
Solderability	MIL-STD
surface mount	NO
Switch action	VERTICAL
switch function	3PDT
Switch type	PUSHBUTTON SWITCH
Terminal surface	GOLD/NICKEL
Terminal length	0.125 inch
Terminal material	COPPER ALLOY
Termination type	SOLDER
Washability	PARTIAL

Preview

Download Datasheet

View All

Printed from www.freetradezone.com, a service of Partminer, Inc.

This Material Copyrighted By Its Respective Manufacturer

Recommended Resources

LED cycle lighting circuit controlled by 12C508A

Integrated OCL power amplifier circuit composed of TDA2040

Used for LOGO! Mud scraper control circuit b

Sound-activated bistable electronic switch circuit

820e computer motherboard circuit diagram_76

555 automobile multi-purpose alarm circuit

Application of SMS modem in low voltage power distribution monitoring: Application of SMS cat in low-voltage power distribution monitoring With the gradual deepening of power grid transformation and the rapid development of power distribution network technology, the scie...; ljh1024 Embedded System

KEIL: The compilation fails and the prompt is TOOL. INI does not contain a tool path...; Kaituozhe1 Embedded System

[TI's first low-power design competition] The first version of the expansion board is back: The board finally came back yesterday, and I worked overtime to solder it.1 Communication module CC2540 This board doesn't seem to be well made. The vias in the design file should be very small, with ...; lonerzf Microcontroller MCU

430F5438 Chinese information: ...; yygyfjkihag Microcontroller MCU

EM78 command system: EM78 command system...; lorant Embedded System

Please help with NRF24L01 chip power consumption issue: Hello everyone! I'm working on a wireless thing, an active electronic tag, using a 2401 chip, but the power consumption is a bit high in the receiving mode. I want to put it in standby mode, so that t...; goldenguy2011 RF/Wirelessly

Development of automotive CAN bus data recorder

1. Introduction Since the 1980s, with the continuous development of automotive electronic technology, there are more and more electronic control units in automobiles, such as electronic fuel i...[Details]
Low-power LED general lighting applications below 30 W

In recent years, lighting has become an important area that countries around the world are targeting to promote energy conservation and environmental protection. According to statistics, about 20% ...[Details]
Measuring the leakage resistance of a capacitor using the Model 6487 Picoammeter Source or the Model 6517A Electrometer

Capacitors are basic components in various electronic devices and are widely used for bypassing, coupling, filtering , tuning, etc. in electronic circuits. However, to use capacitors,...[Details]
Design of Adaptive Digital Sensor Based on FPGA

Abstract: The output of high-range acceleration sensor is less than 10 mV under the excitation of small signal. The noise of traditional test system may cover such small voltage signal, so that hig...[Details]
Design of sensor experimental platform based on wireless sensor network technology

0 Introduction There are many types of sensors, and the working principles, measurement targets and measurement environments of different types of sensors vary greatly. The corresponding detection s...[Details]
The present and future of automotive LEDs

1 Introduction to LED With the development of science and technology, people have higher and higher requirements on automobile light sources. LED (Light Emitting Diode) has gradually attracted...[Details]
LED Floodlights and Floodlights

1 What is an LED floodlight? LED downlights are also called spotlights, projection lamps, and spotlights. They are mainly used for architectural decorative lighting and commercial space lighti...[Details]
Introduction to Clock Distribution System Design in Medical Imaging

The demand for improved healthcare environments is endless, so medical imaging equipment with higher resolution is needed to better observe the human body. High resolution brings problems with sign...[Details]
Battery clamp quick release method

Battery clamps, commonly known as battery connectors, come in two sizes depending on the thickness of the battery terminals. One is the battery clamp used on thick terminals, with a positive termin...[Details]
How to reduce electrostatic interference? Electrostatic shielding can help

Electrostatic coupling and interference occur when a charged object is close to the input of the circuit being measured. At low impedance, the effects of interference are not noticeable because th...[Details]
Methods to reduce power consumption of switching power supply

The power consumption of a switching power supply includes fixed losses caused by parasitic resistances such as semiconductor switches, magnetic components, and wiring, as well as switching losses ...[Details]
Embedded System Design of Mobile Phone Vending Machine

introduction The core features of mobile value-added service products are mobility, immediacy and personalization. Mobile value-added services are a new service mode that is rapidly developing...[Details]
Stepper motor control driver for PLC

Traditionally, when using PLC to control stepper motors, a dedicated stepper motor control intelligent module is usually added to the PLC, and then connected to the drive power supply to realize th...[Details]
Design of motion estimation based on FPGA

Abstract: A motion estimation design for video images is implemented using a powerful FPGA. The search method used is a three-step search method. When designing the scheme, this paper uses the rela...[Details]
PGI releases PGI Accelerator compiler with OpenACC support

The Portland Group, a leading provider of graphics processing units (GPUs) and graphics accelerators, has announced the availability of its PGI Accelerator™ Fortran and C compilers that support the...[Details]

Shortcut: A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 AA AB AC AD AE AF AG AH AI AJ AK AL AM AN AO AP AQ AR AS AT AU AV AW AX AY AZ B0 B1 B2 B3 B4 B5 B6 B7 B8 B9 BA BB BC BD BE BF BG BH BI BJ BK BL BM BN BO BP BQ BR BS BT BU BV BW BX BY BZ C0 C1 C2 C3 C4 C5 C6 C7 C8 C9 CA CB CC CD CE CF CG CH CI CJ CK CL CM CN CO CP CQ CR CS CT CU CV CW CX CY CZ D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 DA DB DC DD DE DF DG DH DI DJ DK DL DM DN DO DP DQ DR DS DT DU DV DW DX DZ

Popular Components