Above ratings are based on the thermal resistances using a multi-layer circuit board (EIA/JESD51). For mounting on a mono-layer board, power derating shall be
needed. Please inquire of us about conditions.
※1 素子毎の負荷電力の合計が、パッケージ定格電力を超えない条件で御½用ください。
※1 Total power consumption of all elements should not exceed the package power rating.
The resistor of this product is formed by narrow patterning a thin metal film. Thus, application of excessive voltage causes burn and destruction of the resistive film, abnormality
in resistance or open resistance and loss of proper function. The properly and electrostatically measured taping materials are used for the components, but attention should be paid
to the fact that there is some danger the parts may be destructed by static electricity(equivalent to 500V or over at 100pF, 1.5kΩ) to cause a change in resistance in the conditions
of an excessive dryness when mounting on the boards. Similarly, care should be given not to apply the excessive static electricity at the time of mounting on the boards. When
designing, consideration can be taken into withstanding ESD for customized KPC products. Please consult with us about the details.
●
Hand soldering by iron soldering or repairment are not recommended because KPC is a multi-pin product.
●
Avoid storing components under direct sun rays, high temperature/humidity. Direct sun rays will cause quality change of taping and difficulty of keeping appropriate peeling
strength. In the case of 5〜35℃/35〜75%RH, there is no deterioration of solderability for 12 months, but take special care for storing, because condensation, dust, and toxic gas
like hydrogen sulfide, sulfurous acid gas, hydrogen chloride, etc. may drop solderability.
Wearable devices are becoming more and more popular nowadays. How can we apply the knowledge we have learned to them? If we want to develop wearable devices in the future, what preparations should we ...
Please look at the following two functions. When the program executes to (1), if an RTC interrupt occurs suddenly, will it cause dyjc not to be equal to 1190 after the close function is executed?The r...
Single chip control system requirements: 1 input, 3 outputs (2 of which control solenoid valve outputs, 1 control relay output) Function: count the input points, input and output once, solenoid valve ...
Physical display:[b]Circuit Function and Advantages[/b] The circuit shown in the figure is a fully isolated low-power pH sensor signal conditioner and digitizer with automatic temperature compensation...
PWM signal is a digital signal with a fixed period and variable duty cycle.
If the counter of Timer_A works in up-counting mode, the output adopts output mode 7 (reset/set mode)
Use register TAxCCR0 t...
When Amazon launched its first
cloud computing
service, the outside world was not optimistic about this direction, as it had high investment, low profits and many uncertainties. Let's follo...[Details]
This is my first time writing an STM32 program. I have many questions to ask. I want to convert the data of the SO of MAX6675 into the actual temperature and read it out using the serial port tool. I...[Details]
ZTE was punished, and Hou Weigui, who had already retired, had to come out of retirement again and run around to mediate. Let's follow the embedded editor to learn about the relevant content.
...[Details]
Site conditions: 1. AD acquisition, DMA transmission; AD is set to single-channel continuous mode, DMA is set to single-shot mode. The upper threshold of the AD analog watchdog setting is less than t...[Details]
According to the description provided in the official manual of ST, it is not difficult to see that the ADC analog watchdog is actually that the user can set an upper and lower limit of the AD value...[Details]
How to convert the pin voltage value into V using the built-in ADC of STM32? V(ADC) = Value(ADC) * V(ref)/4096 (The ADC of STM32 is 12 bits, so the maximum value of the AD word is 4096)
Where V(ADC...[Details]
1. Analysis of the main causes of AVR damage: The AVR circuit consists of three parts: the rectifier main circuit, the voltage detection circuit, and the comparison control circuit. Excluding the...[Details]
"Now I can't even afford a
memory
stick
to equip my computer
." The price of
memory
sticks has risen rapidly recently. Take 8GB Kingston
memory sticks
as an example. Compared...[Details]
Starting this month, 39 electric vehicle charging stations in Urumqi have begun to be upgraded to the new national standard, and it is planned to be completed by the end of the year.
On the 21...[Details]
MSP430 MCU 1602 LCD 60-second timing program //************************************************************** // P3BIT5 connects to RS)-- (BIT7 connects to NE)-- (BIT6 connects to RW) //P4 port sends...[Details]
China Energy Storage Network News:
The Global Energy Internet Seminar, jointly organized by the Global Energy Internet Development Cooperation Organization and the Royal Academy of Engineerin...[Details]
Embedded System
京公网安备 11010802033920号
EEWORLD
