REVISION Z
"A"
DO NOT
SCALE FROM
THIS PRINT
"A"
XX.XX
C
1/8 3.18
IDSX-XX-X-XX.XX-XXX-XXX
ROW SPECIFICATION
-S: SINGLE ROW
-D: DOUBLE ROW
"A"
NO. OF CONDUCTORS
(-02
THRU -36 PER ROW)
USE CABLE: CB-XX-28-7/36-050-C (IDSD)
USE CABLE: CB-XX-28-7/36-100-C (IDSS)
IDSD FULL STRIP: "A"=3.650 .005[92.71 0.13] REF
+.015 [0.38]
CUT STRIP: "A"
-.005 [0.13]
= ("XX" x .100[2.54])+.059[1.50]
IDSS FULL STRIP: "A"=3.610 .005[91.69 0.13] REF
+.015 [0.38]
CUT STRIP: "A"
-.005 [0.13]
= ("XX" x .100[2.54])+.019[0.48]
*NOTE: STANDARD COLOR-CODED CABLE N/A
FOR DOUBLE ROW 31 THRU 36 POSITION -
SEE -G OPTION.
BROWN WIRE INDICATES PIN #1
.010 0.25 MAX (TYP)
C
-S: (SINGLE) ONE IDC ASSEMBLY
-D: (DOUBLE) TWO IDC ASSEMBLYS
MEASURED IN INCHES
END ASSEMBLY SPECIFICATION
-DXX: DAISY CHAIN -DOUBLE (SEE FIG 2, STH 2)
(NOT AVAILABLE WITH -IDSS)
-PXX: POLARIZED MATING (SEE FIG 3, STH 2)
-ST"X": STRIPPED & TINNED (SEE FIG 4, STH 2)
-R: REVERSED CONECTOR (SEE FIG 5, STH 2)
(NOT AVAILABLE WITH -M & -O)
-M: MIDDLE REVERSED (SEE FIG 7, STH 3)
(NOT AVAILABLE WITH -R & -O)
(REQUIRES -SXX, -WXX OR -DXX)
-O: OUTSIDE REVERSED (SEE FIG 8, STH 3)
(NOT AVAILABLE WITH -R & -M)
(REQUIRES -SXX, -WXX OR -DXX)
-RW: REVERSED WIRING (SEE FIG 9, STH 3)
-BXX: BREAKOUT (SEE FIG 6, STH 2)
-SXX: DAISY CHAIN -SINGLE (SEE FIG 10, STH 3)
-WXX: WIRING REVERSED (SEE FIG 11, STH 3)
OPTION SPECIFICATION
LENGTH OF CABLE
"D"
-T: TIN BOTH ENDS
(USE C-10-T)
-G: GRAY CABLE (SEE FIG 1)
SUBSTITUTE GRAY CABLE FOR STANDARD
COLOR CODED CABLE. USE:
IDSD: CB-XX-28-7/36-050-G
IDSS: CB-XX-28-7/36-100-G
(NOTE: USE GRAY CABLE FOR DOUBLE
ROW -31 THRU -36 POSITION)
OPTION SPECIFICATION
ISC-36-D
RIBS OF GRAY CABLE
GO TO CAP SIDE
C
"B"
.093 2.36
"A"
XX.XX
1/8 3.18
"C"
"C"
"B"
C-10-X(G OR T)
IDSD-05-D-XX.XX-XXX-XXX SHOWN
(SEE NOTE 9)
FIG 1
ISB-36-D
SECTION "A"-"A"
IDSS-05-S-XX.XX-XXX-XXX SHOWN
(DIFFERENT AS SHOWN, OTHERWISE SAME AS FIG 1)
ISC-36-S
CONTACT IS ALWAYS ASSEMBLIED TO
INSIDE OF SINGLE ROW CONNECTORS
FIG 2
BROWN WIRE INDICATES PIN #1
NOTES:
1.
C
REPRESENTS A CRITICAL DIMENSION.
2. OPTION -SXX WHEN MATING DOUBLE ROW CONNECTOR WITH 2 SINGLE
ROW CONNECTORS, THE OUTER MOST SINGLE WILL BE CONNECTED TO
CONDUCTOR #1 AND THE INSIDE SINGLE TO CONDUCTOR #2.
3. USING A #32 MICRO FINISHED .025 .0005 [.64 .013] SQ POST,
INSERTION / WITHDRAWAL FORCES TO BE:
INSERTION: 4.0 OZ [114 GRAMS] AVG / 6.0 OZ [170 GRAMS] MAX
WITHDRAWAL: 2.75 OZ [78.0 GRAMS] AVG / 2.0 OZ [57 GRAMS] MIN.
4. MAX ALLOWABLE BOW AFTER ASSEMBLY TO BE .006 INCH/INCH [MM/MM].
5. A CHAMFER ON THE END OF THE CAP IS GUARANTEED ON FINAL ASSEMBLIES
THAT ARE AT LEAST 18 POSITIONS FOR MALE AND FEMALE TERMINATION.
6. ALL ASSEMBLIES TO BE 100% ELECTRICALLY TESTED FOR SHORTS AND OPENS.
7. ALL ASSEMBLIES TO BE 100% HI-POT TESTED AT 1000V.
8. WIRE: 28 AWG, 7/36, TINNED, STRANDED WITH PVC INSULATOR
9. FOR IDSX WITH R OR RW OPTION, CABLE RIB ORIENTATION CAN
BE EITHER TOWARDS OR AWAY FROM THE CAP.
10. WHEN CUTTING CABLE TO LENGTH, CONDUCTORS SHOULD NOT EXTEND
PAST THE CABLE INSULATION, EXTENDING LESS THAN 25% OF CABLE
THICKNESS ON CONSECUTIVE AND LESS THAN 50% OF CABLE THICKNESS
ON NON-CONSECUTIVE STRANDS IS CONSIDERED A PROCESS INDICATOR.
.093 2.36
ISB-36-S
C-10-X(G OR T)
SECTION "B"-"B"
UNLESS OTHERWISE SPECIFIED,
DIMENSIONS ARE IN INCHES.
TOLERANCES ARE:
DECIMALS
THIS DOCUMENT CONTAINS CONFIDENTIAL AND
PROPRIETARY INFORMATION AND ALL DESIGN,
MANUFACTURING, REPRODUCTION, USE, PATENT RIGHTS
AND SALES RIGHTS ARE EXPRESSLY RESERVED BY SAMTEC,
INC. THIS DOCUMENT SHALL NOT BE DISCLOSED, IN WHOLE
OR PART, TO ANY UNAUTHORIZED PERSON OR ENTITY NOR
REPRODUCED, TRANSFERRED OR INCORPORATED IN ANY
OTHER PROJECT IN ANY MANNER WITHOUT THE EXPRESS
WRITTEN CONSENT OF SAMTEC, INC.
SECTION "C"-"C"
*
*
PROPRIETARY NOTE
.XX: .01 [0.3]
2
.XXX: .005 [0.13]
.XXXX: .0020 [0.051]
ANGLES
520 PARK EAST BLVD, NEW ALBANY, IN 47150
PHONE: 812-944-6733
FAX: 812-948-5047
e-Mail info@SAMTEC.com
code 55322
DESCRIPTION:
MATERIAL:
DO NOT SCALE DRAWING
SHEET SCALE: 2:1
INSULATOR: PBT UL94V-0, COLOR: BLACK
CONTACT: BeCu
WIRE: 28 AWG, 7/28, TINNED, STRANDED WITH
COLOR-CODED OR GRAY PVC INSULATOR
C:\EnterpriseVault\DWG\MISC\MKTG\IDSX-XX-X-XX.XX-XXX-XXX-MKT.SLDDRW
ASSEMBLY INSULATION DISPLACEMENT SOCKET CONNECTOR
DWG. NO.
BY:
DEAN P
IDSX-XX-X-XX.XX-XXX-XXX
11/02/1988
SHEET
1
OF
3
REVISION Z
IDSD: DOUBLE
2
4
1 3
1
71
72
36
IDSD
BROWN WIRE
XX 1/8 3.18
(2[51] MIN)
FIRST PRESS END
3
1
24
71
72
IDSS
BROWN WIRE
BROWN WIRE
-DXX SHOWN
(NOT AVAILABLE WITH -DSS)
(DIFFERENT AS SHOWN, OTHERWISE SAME AS FIG 1)
NOTES:
1. 2" MINIMUM LENGTH
2. 1" INCREMENTS ONLY
FIG 2
NOTE:
1. POLARIZED POSITION WILL HAVE SAME ELECTRICAL
POSITION FROM BROWN WIRE.
-PXX: POLARIZED MATING SHOWN
(XX = POSION NO.)
(INSERT POLARIZING KEY PART NO.
PK-06 INTO SPECIFIED POSITION -XX)
(DIFFERENT AS SHOWN, OTHERWISE SAME AS FIG 1)
FIG 3
IDSS: SINGLE
IDSD: DOUBLE
3
+2
76
+51
-1
- 25
IDSS
SEE NOTE 2
.030 0.76 MAX
(AFTER STRIPPED & TINNED)
IDSD
"L"
1/16 1.59
XX
BROWN WIRE
-BXX: BREAKOUT SHOWN
(DIFFERENT AS SHOWN, OTHERWISE SAME AS FIG 1)
IDSD-XX-D-XX-BXX
XX INDICATES NO. OF CONDUCTORS
IDSD-XX-S-XX-BXX
XX INDICATES NO. OF CONDUCTORS
IDSS-XX-D-XX-BXX:
XX INDICATES NO. OF POSITIONS
IDSS-XX-S-XX-BXX:
XX INDICATES NO. OF POSITIONS
THIS DOCUMENT CONTAINS CONFIDENTIAL AND
PROPRIETARY INFORMATION AND ALL DESIGN,
MANUFACTURING, REPRODUCTION, USE, PATENT RIGHTS
AND SALES RIGHTS ARE EXPRESSLY RESERVED BY SAMTEC,
INC. THIS DOCUMENT SHALL NOT BE DISCLOSED, IN WHOLE
OR PART, TO ANY UNAUTHORIZED PERSON OR ENTITY NOR
REPRODUCED, TRANSFERRED OR INCORPORATED IN ANY
OTHER PROJECT IN ANY MANNER WITHOUT THE EXPRESS
WRITTEN CONSENT OF SAMTEC, INC.
FIG 6
1/16 1.59 MAX
FLAT WIRE ALLOWED
-ST"X" SHOWN
(DIFFERENT AS SHOWN, OTHERWISE SAME AS FIG 1)
FIG 4
*
PROPRIETARY NOTE
*
NOTES:
1. CONDUCTORS SHALL BE CONSISTENT IN APPEARANCE.
SOLDER MUST MAINTAIN CABLE STRAINS WITHIN THE
MAX DIA. TOLERANCE.
2. USE LEAD FREE SOLDER ONLY.
3. NOT AVAILABLE IN 28 POSITION AND UP IN DOUBLE ROW ONLY.
BOTH SOCKETS REV.
WHEN DAISY CHAINED
520 PARK EAST BLVD, NEW ALBANY, IN 47150
PHONE: 812-944-6733
FAX: 812-948-5047
e-Mail info@SAMTEC.com
code 55322
DESCRIPTION:
DWG. NO.
-R: REVERSED CONNECTOR SHOWN
(NOT AVAILABLE WITH -M & -O)
(DIFFERENT AS SHOWN, OTHERWISE SAME AS FIG 1)
C:\EnterpriseVault\DWG\MISC\MKTG\IDSX-XX-X-XX.XX-XXX-XXX-MKT.SLDDRW
FIG 5
DO NOT SCALE DRAWING
SHEET SCALE: 2:1
ASSEMBLY INSULATION DISPLACEMENT SOCKET CONNECTOR
BY:
DEAN P
IDSX-XX-X-XX.XX-XXX-XXX
11/02/1988
SHEET
2
OF
3
REVISION Z
STANDARD WIRING
BROWN WIRE INDICATES PIN #1
BROWN WIRE
(BROWN WIRE TO
OPPOSITE SIDE OF
FIRST POSITION)
-M: MIDDLE REVERSED SHOWN
(NOT AVAILABLE WITH -R & -O)
(REQUIRES -SXX, -WXX OR -DXX)
(DIFFERENT AS SHOWN, OTHERWISE SAME AS FIG 1)
FIG 7
-O: OUTSIDE REVERSED SHOWN
(NOT AVAILABLE WITH -R & -M)
(REQUIRES -SXX, -WXX OR -DXX)
(DIFFERENT AS SHOWN, OTHERWISE SAME AS FIG 1)
FIG 8
FIRST POSITION
REVERSED WIRING
FIG 9
-RW: REVERSED WIRING SHOWN
(DIFFERENT AS SHOWN, OTHERWISE SAME AS FIG 1)
IDSD: DOUBLE
IDSS: SINGLE
SINGLE
IDSD: DOUBLE
IDSS: SINGLE
SINGLE
OUTER MOST
OUTER MOST
BROWN WIRE
BROWN WIRE
XX 1/8 3.18
(2[51] MIN)
FIRST PRESS END
XX 1/8 3.18
(2[51] MIN)
FIRST PRESS END
-WXX: WIRING REVERSED SHOWN
(DIFFERENT AS SHOWN, OTHERWISE SAME AS FIG 1)
NOTE:
1. OPTION -SXX WHEN MATING DOUBLE ROW CONNECTOR WITH 2 SINGLE ROW CONNECTORS,
THE OUTER MOST SINGLE WILL BE CONNECTED TO CONDUCTOR #1 AND THE INSIDE SINGLE
TO CONDUCTOR #2.
THIS DOCUMENT CONTAINS CONFIDENTIAL AND
PROPRIETARY INFORMATION AND ALL DESIGN,
MANUFACTURING, REPRODUCTION, USE, PATENT RIGHTS
AND SALES RIGHTS ARE EXPRESSLY RESERVED BY SAMTEC,
INC. THIS DOCUMENT SHALL NOT BE DISCLOSED, IN WHOLE
OR PART, TO ANY UNAUTHORIZED PERSON OR ENTITY NOR
REPRODUCED, TRANSFERRED OR INCORPORATED IN ANY
OTHER PROJECT IN ANY MANNER WITHOUT THE EXPRESS
WRITTEN CONSENT OF SAMTEC, INC.
FIG 11
SXX: DAISY CHAIN - SINGLE SHOWN
(DIFFERENT AS SHOWN, OTHERWISE SAME AS FIG 1)
FIG 10
*
PROPRIETARY NOTE
*
NOTE:
1. OPTION -SXX WHEN MATING DOUBLE ROW CONNECTOR WITH 2 SINGLE ROW CONNECTORS,
THE OUTER MOST SINGLE WILL BE CONNECTED TO CONDUCTOR #1 AND THE INSIDE SINGLE
TO CONDUCTOR #2.
520 PARK EAST BLVD, NEW ALBANY, IN 47150
PHONE: 812-944-6733
FAX: 812-948-5047
e-Mail info@SAMTEC.com
code 55322
DESCRIPTION:
DO NOT SCALE DRAWING
SHEET SCALE: 2:1
ASSEMBLY INSULATION DISPLACEMENT SOCKET CONNECTOR
DWG. NO.
C:\EnterpriseVault\DWG\MISC\MKTG\IDSX-XX-X-XX.XX-XXX-XXX-MKT.SLDDRW
BY:
DEAN P
IDSX-XX-X-XX.XX-XXX-XXX
11/02/1988
SHEET
3
OF
3
Special Edition for Assessment Centres
京公网安备 11010802033920号
EEWORLD
