Note: A 0.01 Ohm addition to be added to the performance of all resistors <10 Ohms.
Pulse Performance Data
Lightning Surge
Lightning surge resistors are tested in accordance with IEC 60 115-1 using both 1.2/50µs and 10/700µs pulse shapes. 10 pulses are applied. The limit of
acceptance is a shift in resistance of less than 1% from the initial value.
2512
2010
1206
0805
0603
2512
2010
1206
0805
0603
General Note
TT Electronics reserves the right to make changes in product specification without notice or liability.
All information is subject to TT Electronics’ own data and is considered accurate at time of going to print.
The single impulse graph is the result of 50 impulses of rectangular shape applied at one minute intervals. The limit of acceptance was a shift in
resistance of less than 1% from the initial value.
2512
2010
1206
0805
0603
Continuous Load Due to Repetitive Pulses
The continuous load graph was obtained by applying repetitive rectangular pulses where the pulse period was adjusted so that the average
power dissipated in the resistor was equal to its rated power at 70°C. Again the limit of acceptance was a shift in resistance of less than 1% from the
initial value
2512
2010
1206
0805
0603
General Note
TT Electronics reserves the right to make changes in product specification without notice or liability.
All information is subject to TT Electronics’ own data and is considered accurate at time of going to print.
This course "From System Level to Circuit Level" focuses on the theme of weak signal processing circuits. The content is organized from system level to circuit level. The teaching goal of system level...
I want to make an LCD industrial intelligent liquid crystal circuit controlled by a single-chip microcomputer. I know the interface definition and the serial communication and parallel communication t...
>> >>> If you can see this, please forward it to every friend you care about! >>> Case 1: >>> >>> A woman's handbag was stolen, which contained a mobile phone, bank card, wallet, etc. >>> 20 minutes l...
[i=s] This post was last edited by bqgup on 2021-5-6 17:26 [/i] # HyperLynx High-speed Circuit Design and Simulation (II) Reflection when transmission line impedance and power supply impedance are not...
1. Purpose In actual product release, if the program stored in the MCU Flash is not protected, some illegal companies may read the program in the Flash through an emulator (J-Link, ST-Link, e...[Details]
The trade war between China and the United States has become the focus. The United States has begun to play the ban card against Chinese technology companies. The ZTE incident shows that if the ban...[Details]
0. Preparation First use st-link to connect the stm32 core board and PC for burning St-link Stm32 3.3V 3.3V GND GND SWDIO PART SWCLK DCLK Then connect with USB serial port board to v...[Details]
After we understand the use of libopencm3, we find that libopencm3 is only suitable for small projects. Its biggest feature is the convenience of USB. So when we configure large projects, is there a ...[Details]
Development Background: 1. Main chip - STM32F207VCT6; 2. TCP/IP protocol stack - LWIP, transplanted based on ST routines; 3. Operating system - none (bare metal); Anomalies: 1. Power on the device wi...[Details]
In the Chinese automobile market, the trend of new energy vehicles and driverless cars is leading the transformation of China's automobile industry. As the world's largest automobile market, "Chinese...[Details]
With the implementation of the first version of the NR sub-6GHz draft of 3GPP in December 2017, and the subsequent Phase 2 drafts, semiconductor manufacturers and terminal manufacturers began to ...[Details]
Nowadays, everyone is saying that "technology is people-oriented". The essence of the development of technology is to serve the improvement of the quality of life of human beings. Automated driving...[Details]
STM32 uses FSMC to read and write CPLD programs. CPLD is hung on the address line and data line of STM32. CPLD is regarded as an off-chip RAM for reading and writing. On the board I made, CPLD is hun...[Details]
Temperature, humidity and irradiance are must-measure items in the photovoltaic industry. However, most of the current data collection is done by storing data in USB flash drives for offline analys...[Details]
In recent years, in addition to Huawei Kirin
chips
in the mobile phone industry
, Xiaomi's own processor Pengpai S1, AI
chip
start-ups such as Cambrian, Horizon, and Deephi Technolo...[Details]
The clock system of STM32 can be directly summarized in a diagram (from the STM32F10X reference manual). The following is an analysis of this diagram 1. STM32 input clock source 1.1 Function of cl...[Details]
The key is the configuration of registers. The T1 timer (16 bits) of CC2530 needs to configure three registers: T1CTL, T1STAT, IRCON Here is just a brief introduction. For more details, please refer ...[Details]
MCS-51 single-chip microcomputer timer/counter experiment programming program Programming requirements: 1. Connect a light-emitting diode LED to the P1.0 pin, light up for two seconds, turn off for o...[Details]
Training Edition
京公网安备 11010802033920号
EEWORLD
