302075-711K300BB datasheet, PDF

Datasheet> All Categories > Passive components> The resistor> 302075-711K300BB

302075-711K300BB: DescriptionFixed Resistor, Metal Foil, 1.75W, 11300ohm, 600V, 0.1% +/-Tol, -2,2ppm/Cel,; CategoryPassive components The resistor; File Size451KB，6 Pages; ManufacturerVishay; Websitehttp://www.vishay.com

Download Datasheet Parametric View All

302075-711K300BB Overview

Fixed Resistor, Metal Foil, 1.75W, 11300ohm, 600V, 0.1% +/-Tol, -2,2ppm/Cel,

302075-711K300BB Parametric

Parameter Name	Attribute value
Is it Rohs certified?	incompatible
Objectid	851120249
Reach Compliance Code	compliant
ECCN code	EAR99
structure	Hermetically Sealed
JESD-609 code	e0
Lead diameter	0.64 mm
Lead length	25.4 mm
Number of terminals	4
Maximum operating temperature	125 °C
Minimum operating temperature	-55 °C
Package diameter	12.7 mm
Package length	38.1 mm
Package form	4 Terminals
method of packing	Bulk
Rated power dissipation(P)	1.75 W
resistance	11300 Ω
Resistor type	FIXED RESISTOR
series	H(OTHER)
technology	METAL FOIL
Temperature Coefficient	-2,2 ppm/°C
Terminal surface	Tin/Lead (Sn/Pb)
Tolerance	0.1%
Operating Voltage	600 V

Preview

Download Datasheet

View All

H Series

Vishay Foil Resistors

New Generation of Secondary Standards Hermetically Sealed High Precision Bulk

Metal

Foil Technology Resistors with TCR of ± 2 ppm/°C, Tolerance of ± 0.001 % and

Load Life Stability of ± 0.005 % (Metrology, Laboratory, Instrumentation, Industrial)

FEATURES

•

Temperature coefficient of resistance (TCR):

± 2 ppm/°C typical (- 55 °C to + 125 °C, + 25 °C

ref.).

For

ultra

high

performances

(instrumentation and metrology) please refer to

the last page

•

Resistance range: 5

to 1.84 MΩ (higher or

lower values of resistance available)

•

Vishay Foil resistors are not restricted to standard values;

specific “as required” values can be supplied at no extra

cost or delivery (e.g. 1K2345 vs. 1K)

•

Power rating: 0.3 W to 2.5 W at + 25 °C (depending on

model - see table 2)

•

Tolerance: to ± 0.001 % (10 ppm)

•

Load life stability to ± 0.002 % (20 ppm) at 25 °C, 2000 h

at rated power

•

Load life stability can be considerably improved

through in-house stabilization

•

Shelf life stability: ± 2 ppm for at least 6 years

(unaffected by humidity)

•

Electrostatic discharge (ESD) up to 25 000 V

•

Rise time: 1 ns effectively no ringing

•

Thermal stabilization time < 1 s (nominal value achieved

within 10 ppm of steady state value)

•

Current noise: 0.010 µV

RMS

/V of applied voltage (< - 40 dB)

•

Thermal EMF: 0.05 µV/°C typical

•

Voltage coefficient: < 0.1 ppm/V

•

Non-inductive: < 0.08 µH

•

Non-inductive, non-capacitive design

•

Non hot spot design

•

Terminal finish available: lead (Pb)-free or tin/lead alloy

•

Impervious to harmful environments - oil-filled

•

Compliant to RoHS directive 2002/95/EC

•

Prototype quantities available in just 5 working days

or sooner. For more information, please contact

foil@vishaypg.com

•

For better performances (values, TCR, tolerance, stability),

please see the HZ series

INTRODUCTION

The H series resistors are oil-filled, hermetically sealed ultra

precision resistors and are used as secondary standards for

metrology applications.

The hermetic sealing eliminates the ingress of moisture and

oxygen, while the oil acts as a thermal conductor, thus

eliminating the long-term degradation elements of unsealed

resistors, while at the same time allowing the device to

accept short periods of overload without degradation.

Vishay’s Bulk Metal

Foil outperforms all other resistor

technologies available today for applications that require

precision and stability. When combined with the hermetic

sealing and oil filling, the H series resistors become

the most

precise and stable resistors available.

With accuracies of 0.001 %, a resistance range from 5

to 1.84 MΩ, and long term shelf life of less than 2 ppm,

these devices are virtually secondary standards that can be

carried in sets for daily or periodic calibration of factory

measurement equipment.

The H series is available with laboratory and metrology

level precision and long-term stability with additional

in-house oriented processes such as: chip stabilization,

special TCR plotting, additional treatments for ultra

stability and special post manufacturing operations

(PMO). (Please refer to the last page)

TABLE 1 - TCR VS. RESISTANCE VALUE

RESISTANCE

VALUE (Ω)

100 to < 1M84

50 to < 100

5 to < 50

TYPICAL TCR AND MAX. SPREAD

(- 55 °C to + 125 °C, + 25 °C ref.)

(ppm/°C)

± 2 ± 2.5

± 2 ± 3.5

± 2 ± 4.5

FIGURE 1 - SHELF LIFE - VHA518-11

12K9 VS. QHE

0.9

0.8

0.7

0.6

0.5

0.4

0.3

0.2

0.1

- 0.1

100 200 300 400 500 600 700 800 900 1000

Note

• For maximum TCR < 1 ppm/°C, see VHP100 and contact

application engineering

* Pb containing terminations are not RoHS compliant, exemptions may apply

Resistance Change (ppm)

Time (Days)

Document Number: 63006

Revision: 23-Mar-10

For any questions, contact:

foil@vishaypg.com

www.foilresistors.com

Recommended Resources

Incandescent lamp dimming circuit

Quartz oscillator diseases circuit and calculation-series crystal oscillator

One of the phase loss alarm circuits

Isolated sensor bridge system measurement circuit

800Hz Wien Bridge Oscillator Circuit

IGBT application circuit in telephone interface

Why is the square wave voltage generated by the inverter circuit measured using the AC voltage range of a digital multimeter much smaller than the theoretical value?: Using the AC voltage range of a digital multimeter to measure the square wave voltage generated by the inverter circuit shows only 0.3V, but it should actually be around 10V. My instructor gave me a w...; 寒香随彩蝶 Switching Power Supply Study Group

Experts~ Can you help me with the issue of IO simulation UART?: I use IO to judge whether there is data incoming. When doing the receiving and transmitting in timerA, it is normal for me to write the transmitting and receiving separately, but when they are combine...; lavender780510 Microcontroller MCU

Urgent question about microcontroller: I am using E2000/L simulator and 196KC simulator head. I want to program in C language under WAVE6000. How can I do this? I have Tasking C196. How can I install it? What are the specific steps for deb...; wybetter Embedded System

The watchdog timer generates PWM waves: My 430 MCU's TA and TB timers are all used up, so I want to use the watchdog timer to generate PWM waves. I'm looking for a program to use the watchdog timer to generate PWM waves!!!...; cczuzmk Microcontroller MCU

What do the numbers and letters on the CBB capacitor mean?: What do the math and letters on this mean? A(R)49 332J Is this the CBB capacitor for calibration? Please give me some advice. . ....; NJ_Cole Analog electronics

Discussion and Prospect of High Power LED Packaging: [hide]For a long time, when the requirements for LED heat dissipation are not very high, LEDs are mostly packaged using traditional resin substrates. However, with the continuous expansion of market a...; 探路者 LED Zone

Shortcut: L0 L1 L2 L3 L4 L5 L6 L7 L8 L9 LA LB LC LD LE LF LG LH LI LJ LK LL LM LN LO LP LQ LR LS LT LU LV LW LX LY LZ M0 M1 M2 M3 M4 M5 M6 M7 M8 M9 MA MB MC MD ME MF MG MH MI MJ MK ML MM MN MO MP MQ MR MS MT MU MV MW MX MY MZ N0 N1 N2 N3 N4 N5 N6 N7 N8 NA NB NC ND NE NF NG NH NI NJ NK NL NM NN NO NP NQ NR NS NT NU NV NX NZ O0 O1 O2 O3 OA OB OC OD OE OF OG OH OI OJ OK OL OM ON OP OQ OR OS OT OV OX OY OZ P0 P1 P2 P3 P4 P5 P6 P7 P8 P9 PA PB PC PD PE PF PG PH PI PJ PK PL PM PN PO PP PQ PR PS PT PU PV PW PX PY PZ Q1 Q2 Q3 Q4 Q5 Q6 Q8 Q9 QA QB QC QE QF QG QH QK QL QM QP QR QS QT QV QW QX QY R0 R1 R2 R3 R4 R5 R6 R7 R8 R9 RA RB RC RD RE RF RG RH RI RJ RK RL RM RN RO RP RQ RR RS RT RU RV RW RX RY RZ

Popular Components